EN 4041-2006 en Aerospace series - Bearings airframe rolling - Rigid single row ball bearings in corrosion resisting steel with extended inner ring and flanged alignment bush - Dim.pdf

《EN 4041-2006 en Aerospace series - Bearings airframe rolling - Rigid single row ball bearings in corrosion resisting steel with extended inner ring and flanged alignment bush - Dim.pdf》由会员分享，可在线阅读，更多相关《EN 4041-2006 en Aerospace series - Bearings airframe rolling - Rigid single row ball bearings in corrosion resisting steel with extended inner ring and flanged alignment bush - Dim.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIESBS EN4041:2006Bearings, airframe rolling Rigid single row ball bearings in corrosion resisting steel, with extended inner ring and flanged alignment bush Dimensions and loadsThe European Standard EN 4041:2006 has the status of a British StandardICS 49.035g49g50g3g38g

2、50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 4041:2006This British Standard was published under the authority of the Standards Policy and Strategy Comm

3、ittee on 30 June 2006 BSI 2006ISBN 0 580 48438 6National forewordThis British Standard is the official English language version of EN 4041:2006. The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems, which has the responsibilit

4、y to: A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “Internationa

5、l Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British St

6、andard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European

7、 developments and promulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 10, an inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments

8、 issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 4041June 2006ICS 49.035English VersionAerospace series - Bearings, airframe rolling - Rigid single rowball bearings in corrosion resisting steel, with extended innerring and flanged alignment bush - Dime

9、nsions and loadsSrie arospatiale - Roulements pour structures daronefs- Roulements en acier rsistant la corrosion, rigides, une range de billes, avec bague intrieure jupe et baguedalignement collerette - Dimensions et chargesLuft- und Raumfahrt - Flugwerklager - EinreihigeRillenkugellager aus korros

10、ionsbestndigem Stahl miteinseitig verlngertem Innenring und selbsteinstellendemFlansch - Mae und BelastungenThis European Standard was approved by CEN on 20 April 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanSta

11、ndard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French,

12、German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, De

13、nmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATI

14、ONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 4041:2006: E2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definiti

15、ons .5 4 Symbols and abbreviations 5 5 Required characteristics.5 6 Designation . 10 7 Marking 10 8 Technical specification 10 EN 4041:20063 Foreword This European Standard (EN 4041:2006) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After e

16、nquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a na

17、tional standard, either by publication of an identical text or by endorsement, at the latest by December 2006, and conflicting national standards shall be withdrawn at the latest by December 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of

18、patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, C

19、zech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 4041:20064 1 Scope This standard specif

20、ies the characteristics of rigid single row ball bearings in corrosion resisting steel with an extended inner ring and a solid or lightweight flanged alignment bush, designed to withstand only slow rotations and slight oscillations under load. They are intended for use in airframe fixed and moving e

21、lements and in flight control linkages. The bearings defined in this standard shall be used in the temperature range from 54 C to 150 C. However, as they are lubricated with the following greases (see EN 3727): ester type very high pressure grease (code letter A), operating range from 73 C to 121 C

22、or, synthetic hydrocarbons type very high pressure grease general purpose (code letter B) operating range from 54 C to 177 C. Their field of application when lubricated with code letter A grease is limited to 121 C. 2 Normative references The following referenced documents are indispensable for the

23、application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1132-1, Rolling bearings Tolerances Part 1: Terms and Definitions. ISO 8075, Aerospace Surface treatment o

24、f hardenable stainless steel parts. EN 2030, Steel FE-PM43 Hardened and tempered Bars D 150 mm Aerospace series.1)EN 2226, Steel FE-PM43 Hardened and tempered Hand and die forgings De 150 mm Aerospace series. 1)EN 2424, Aerospace series Marking of aerospace products. EN 2502, Steel FE-PM66 930 Rm 1

25、080 MPa Bars De 150 mm Aerospace series. 1)EN 2503, Steel FE-PM66 930 Rm 1 080 MPa Forgings De 150 mm Aerospace series. 1)EN 25392), Aerospace series Steel FE-PM3801(X5CrNiCu17-4) Air melted Solution treated and precipitation treated - Bar a or D 200 mm Rm 965 MPa.3)EN 3161, Aerospace series Steel F

26、E-PM3801 (X5CrNiCu17-4) Air melted Solution treated and precipitation treated Bar a or D 200 mm Rm 930 MPa. 3)EN 3727, Aerospace series Bearings, airframe rolling rigid with flanged alignment housing Dimensions and mass. 1) Published as AECMA Standard at the date of publication of this standard. 2)

27、Inactive for new design, see EN 3161. 3) Published as AECMA Prestandard at the date of publication of this standard. EN 4041:20065 3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in ISO 1132-1 and the following apply. 3.1 bearing full complement of

28、 balls (without retainer), with filling slot 4 Symbols and abbreviations dmp= single plane mean bore diameter deviation ds= deviation of a single bore diameter Cs= permissible static radial load Famax.= permissible static axial load Ga= axial internal clearance Gr= radial internal clearance Sia= ass

29、embled bearing inner ring face runout with raceway Sea= assembled bearing outer ring face runout with raceway Kia= radial runout of assembled bearing inner ring Kea= radial runout of assembled bearing outer ring 5 Required characteristics 5.1 Configuration, dimensions, tolerances, clearances, torque

30、s and masses Configuration and values: according to Figures 1 to 4 and Table 1; the bearings are fitted either with seals or shields; the flanged alignment bush is either solid or lightweight. The dimensions and tolerances are expressed in millimetres and apply after surface treatment. EN 4041:20066

31、 aIn both positions at 180 from the bearing NOTE Break sharp edges 0,1 to 0,4; the edges of spherical surfaces shall be carefully rounded off. Figure 1 aTransition area at the manufacturers discretion Figure 2 Solid flanged alignment bush, code letter C Figure 3 Lightweight flanged alignment bush, c

32、ode letter D EN 4041:20067 Type with shields code letter P Type with seals code letter E NOTE 1 Installation of seals and shields is at the manufacturers option. NOTE 2 The shields shall not extend beyond width C. Figure 4 Table 1 d Tolerances m A B C D d1E E1J H r Code number nom. dmpdsnom. 0,150 0

33、,12 0,2 0,05 1 1 0 0,1 0,15 n Num-ber of holes min.a 1 32 32 66 77 52 56 55 35 23035 35 69 9 7 80 55 59 58 38 19 22012 40 40 75 86 61 66 64 43 45 45 80 91 66 71 68 48 4 2 50 50 0 12 + 3 15 86 10 8 97 72 77 74 53 20 14015 63 63 0 15 + 4 19 100 11 9 111 86 97 90 67 21 6 0,3to 0,8 130 22 Internal clear

34、ances b m Runout tolerances b max. m Tilting torqueN.m Starting torquebmax. mN.m Masses g/pieces Axial max. Radial Axial Radial d Code number GaGrSiaSeaKiaKeaCode letter P Code letter E Code letter CCode letter D32 2 to 7 21 30 107 91 35 1 to 4 27 35 125 97 40 33 44 143 121 45 1,3 to 4,5 39 53 155 1

35、36 50 1,5 to 5 48 68 175 152 63 120 2 to 9 40 40 25 40 2 to 6 83 113 235 205 aMaximum values for the user. bSee EN 3727. EN 4041:20068 5.2 Loads See Tables 2 and 3. Table 2 Loads for bearings with code letter C alignment bush Permissible static loadsa kN Axial Radial Csfor a displacement of max.: fo

36、r a displacement of max.: d Code number 0,1 mm 0,15 mm 0,2 mm 0,1 mm 0,15 mm 0,2 mm 32 24,5 35 1,32 1,78 2,16 1,8 2,5 3,2 25,5 40 1,3 1,75 2,13 1,78 2,48 3,18 29,5 45 1,27 1,72 2,08 1,75 2,44 3,13 32,4 50 1,2 1,67 2 1,68 2,37 3,03 35,3 63 0,92 1,11 1,29 1,16 1,46 1,78 39,2 aAxial and radial loads ma

37、y be applied simultaneously. For ultimate static loads, see EN 3727. EN 4041:20069 Table 3 Loads for bearings with code letter D alignment bush Permissible static loadsa kN Axial Radial Csfor a displacement of max.: for a displacement of max.: d Code number 0,1 mm 0,15 mm 0,2 mm 0,1 mm 0,15 mm 0,2 m

38、m 32 24,5 35 25,5 40 29,5 45 32,4 50 0,84 1,1 1,06 35,3 63 0,99 1,17 1,3 1,18 1,37 1,57 39,2 aAxial and radial loads may be applied simultaneously. For ultimate static loads, see EN 3727. 5.3 Surface roughness Raceways and balls: Ra= 0,2 m Bore, side faces of bearing and bearing/bush swivelling surf

39、aces: Ra= 0,8 m Embedding diameter and support face of the bush: Ra= 1,6 m General state: Ra= 3,2 m The values apply prior to surface treatment. 5.4 Materials Bush: EN 2502 or EN 2503 or EN 2539, 29 HRC to 37 HRC Inner ring: EN 2030 or EN 2226, on the side with raceway 58 HRC, on the side with fixin

40、g holes 20 HRC to 30 HRC Outer ring: EN 2030 or EN 2226, 58 HRC Balls: EN 2030, 58 HRC Shields: corrosion resisting material Seals: polytetrafluoroethylene (PTFE) or polytetrafluoroethylene (PTFE) reinforced with glass fabric. EN 4041:200610 5.5 Surface treatment Passivation according to ISO 8075: c

41、ode T With no surface treatment: without code 6 Designation EXAMPLE Description block BEARING Identity block EN4041A32PCT Number of this standard Code letter for grease type (see Clause 1) Diameter code number of d (see Table 1) Type code letter (see Figure 4) Alignment bush code letter (see Figures

42、 2 and 3) Surface treatment code (see 5.5) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 7 Marking According to EN 2424, category A The marking position is at the manufacturers option. 8 Technical specification According to EN 3727 EN 4041:20

43、06blankBS EN 4041:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBr

44、itish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity w

45、hile using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscr

46、ibers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI

47、 website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European an

48、d international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: in

49、fobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British