EN 204-2016 en Classification of thermoplastic wood adhesives for non-structural applications《非结构性应用热塑性木材胶粘剂的分类》.pdf

《EN 204-2016 en Classification of thermoplastic wood adhesives for non-structural applications《非结构性应用热塑性木材胶粘剂的分类》.pdf》由会员分享，可在线阅读，更多相关《EN 204-2016 en Classification of thermoplastic wood adhesives for non-structural applications《非结构性应用热塑性木材胶粘剂的分类》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 204:2016Classification of thermoplasticwood adhesives for non-structural applicationsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 204:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 204:2016. Itsupersedes BS E

2、N 204:2001 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/52, Adhesives.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a c

3、ontract. Users are responsible for its correctapplication. The British Standards Institution 2016. Published by BSI StandardsLimited 2016ISBN 978 0 580 89029 1ICS 83.180Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the autho

4、rity of theStandards Policy and Strategy Committee on 31 August 2016.Amendments issued since publicationDate Text affectedBS EN 204:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 204 August 2016 ICS 83.180 Supersedes EN 204:2001English Version Classification of thermoplastic wood adhesives

5、 for non-structural applications Classification des colles thermoplastiques pour bois usages non structuraux Klassifizierung von thermoplastischen Holzklebstoffen fr nichttragende Anwendungen This European Standard was approved by CEN on 8 July 2016. CEN members are bound to comply with the CEN/CENE

6、LEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre o

7、r to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the off

8、icial versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands

9、, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of

10、 exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 204:2016 EBS EN 204:2016EN 204:2016 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 5 4 Classification . 5 5 Test method 6 6 Requi

11、rements . 6 Bibliography 8 BS EN 204:2016EN 204:2016 (E) 3 European foreword This document (EN 204:2016) has been prepared by Technical Committee CEN/TC 193 “Adhesives”, the secretariat of which is held by AENOR. This European Standard shall be given the status of a national standard, either by publ

12、ication of an identical text or by endorsement, at the latest by February 2017, and conflicting national standards shall be withdrawn at the latest by February 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be

13、 held responsible for identifying any or all such patent rights. This document supersedes EN 204:2001. Compared to EN 204:2001 the following modifications have been made: a) references to tests with thick bond lines have been removed; b) assessment is based on 20 test pieces; c) additional informati

14、on on conditioning sequences added in Table 2. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, For

15、mer Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 204:2016EN 204:2016 (E) 4 Introduc

16、tion European Standards giving a common classification with respect to durability classes for wood adhesives will allow considerable improvement in consumer protection in any future product liability system with regard to properties guaranteed by the adhesive manufacturer. BS EN 204:2016EN 204:2016

17、(E) 5 1 Scope This European Standard classifies thermoplastic resin based wood adhesives for non-structural applications into durability classes D1 to D4 based on the dry and wet strengths of bond-lines measured under specified conditions after various conditioning treatments. For special applicatio

18、ns, further tests that do not fall within the scope of this European standard can be applicable. The adhesives specified in this European standard are suitable for the bonding of furniture and interior structures, panelling, doors, windows, stairs etc. made of wood or derived timber products. This E

19、uropean Standard does not specify the temperature resistance of bond-lines. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated re

20、ferences, the latest edition of the referenced document (including any amendments) applies. EN 205:2016, Adhesives Wood adhesives for non-structural applications Determination of tensile shear strength of lap joints EN 923, Adhesives - Terms and definitions 3 Terms and definitions For the purposes o

21、f this document, the terms and definitions given in EN 923 and the following apply. 3.1 thermoplastic resin thermoplast polymer or copolymer capable of being softened by heating and hardened by cooling SOURCE: EN 923:2015, modified NOTE 1 to entry has been removed 3.2 thermoplastic wood adhesive adh

22、esive whose main constituent is a thermoplastic resin and which has been formulated for bonding wood 4 Classification An adhesive shall be classified in accordance with Table 1, which gives examples of climatic conditions and fields of application in which the bonded member is to be used. The classi

23、fication shall be based on tests on thin bond-lines as defined in EN 205:2016. BS EN 204:2016EN 204:2016 (E) 6 Table 1 Description of durability classes Durability class Examples of climatic conditions and fields of application D1 Interior, in which the moisture content of the wood does not exceed 1

24、5 % D2 Interior with occasional short-term exposure to running or condensed water and/or to occasional high humidity provided the moisture content of the wood does not exceed 18 % D3 Interior with frequent short-term exposure to running or condensed water and/or to heavy exposure to high humidity. E

25、xterior not exposed to weather D4 Interior with frequent long-term exposure to running or condensed water. Exterior exposed to weather but with protection by an adequate surface coating 5 Test method The adhesive shall be tested in accordance with EN 205:2016 and as follows: a) bond-lines shall be t

26、ested according to their assigned durability class (see Table 1); b) the tests shall be performed using the appropriate conditioning sequence given in Table 2; c) the individual strength values in N/mm2rounded to 0,1 N/mm2and the mean value of the 20 test pieces for each conditioning sequence shall

27、be recorded. Results from tests in which failure occurred in the wood at values below the specified minimum are invalid. Test pieces that are twisted, bended or showing other irregularities in form are valid if they reach the requirements; otherwise, or if visual examination shows that the adhesive

28、was not correctly applied, the results are invalid. All results, valid or invalid, shall be reported. Explanation of the invalid values shall be reported. The standard atmosphere used as a control climate is either (20 2) C and (65 5) % relative humidity (RH), (20/65), or (23 2) C and (50 5) % relat

29、ive humidity (RH), (23/50). 6 Requirements When tested in accordance with EN 205:2016 the mean strength of an adhesive shall conform to the values shown in Table 2. BS EN 204:2016EN 204:2016 (E) 7 Table 2 Minimum values of adhesives strength for thin bond-lines Conditioning sequences Adhesive streng

30、th in N/mm2Durability classes Sequence number Duration and condition D1cD2cD3cD4c1 7 daysain standard atmosphereb 10 10 10 10 2 7 days in standard atmosphere 3 h in water at (20 5) C 7 days in standard atmosphere 8 3 7 days in standard atmosphere 4 days in water at (20 5) C 2 4 4 7 days in standard

31、atmosphere 4 days in water at (20 5) C 7 days in standard atmosphere 8 5 7 days in standard atmosphere 6 h in boiling water 2 h in water at (20 5) C 4 In each conditioning sequence, specimens shall change from one step to another immediately (not gradually). For the conditioning sequences 3 and 5 th

32、e specimens shall be tested in wet state after removing them from water. NOTE 1 The seven days in standard atmosphere are included in the conditioning time mentioned EN 205:2016, 6.2. NOTE 2 A longer conditioning time between gluing and testing might be necessary as advised by the adhesive manufactu

33、rer. NOTE 3 The number used in the designation does not indicate ranking order. A given adhesive can be assigned to more than one durability class. a1 day = 24 h. b(20 2) C and (65 5) % relative humidity or (23 2) C and (50 5) % relative humidity. cAll minimum values indicated in the columns of dura

34、bility classes D1 to D4 shall be reached as mean values for the classification of an adhesive (for example for D4, the conditioning sequences are 1, 3 and 5). = No test required. BS EN 204:2016EN 204:2016 (E) 8 Bibliography 1 EN 12765, Classification of thermosetting wood adhesives for non-structura

35、l applications This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Stan

36、dards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a depen

37、dable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Stand

38、ards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased

39、. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or som

40、e person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard

41、 to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy

42、 format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or interna

43、l company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy

44、of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of s

45、ubscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/

46、7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to

47、BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards pu

48、blications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or rev

49、ision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): Subscripti