EN 1559-5-2017 en Founding - Technical conditions of delivery - Part 5 Additional requirements for magnesium alloy castings《铸造-交货技术条件-第5部分 镁合金铸件的附加要求》.pdf

《EN 1559-5-2017 en Founding - Technical conditions of delivery - Part 5 Additional requirements for magnesium alloy castings《铸造-交货技术条件-第5部分 镁合金铸件的附加要求》.pdf》由会员分享，可在线阅读，更多相关《EN 1559-5-2017 en Founding - Technical conditions of delivery - Part 5 Additional requirements for magnesium alloy castings《铸造-交货技术条件-第5部分 镁合金铸件的附加要求》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 1559-5:2017Founding Technicalconditions of deliveryPart 5: Additional requirements formagnesium alloy castingsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 1559-5:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN

2、 1559-5:2017. It supersedes BS EN 1559-5:1998 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee ISE/111, Steel Castings and Forgings.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does n

3、ot purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 91097 5 ICS 77.150.20 Compliance with a British Standard cannot confer immunity from legal

4、 obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 1559-5:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1559-5 March 2017 ICS 7

5、7.150.20 Supersedes EN 1559-5:1997English Version Founding - Technical conditions of delivery - Part 5: Additional requirements for magnesium alloy castings Fonderie - Conditions techniques de fourniture - Partie 5 : Spcifications complmentaires pour les pices moules en alliages de magnsium Gieereiw

6、esen - Technische Lieferbedingungen - Teil 5: Zustzliche Anforderungen an Gussstcke aus Magnesiumlegierungen This European Standard was approved by CEN on 6 January 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European

7、 Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (E

8、nglish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgiu

9、m, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,

10、Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN na

11、tional Members. Ref. No. EN 1559-5:2017 EBS EN 1559-5:2017EN 1559-5:2017 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Terms and definitions 5 4 Information to be supplied by the purchaser . 6 5 Designations 6 6 Manufacture 7 7 Requirements . 7 8 Inspe

12、ction 8 9 Marking . 9 10 Packaging and surface protection . 9 11 Complaints . 9 Annex A (informative) Significant technical changes between this European standard and the previous edition 10 BS EN 1559-5:2017EN 1559-5:2017 (E) 3 European foreword This document (EN 1559-5:2017) has been prepared by T

13、echnical Committee CEN/TC 190 “Foundry Technology”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2017, and conflicting national standards shal

14、l be withdrawn at the latest by September 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1559-5:1997. Within its p

15、rogramme of work, Technical Committee CEN/TC 190 requested CEN/TC 190/WG 9 “Cast Magnesium” to revise the following standard: EN 1559-5:1997, Founding Technical conditions of delivery Part 5: Additional requirements for magnesium alloy castings Annex A provides details of significant technical chang

16、es between this European Standard and the previous edition. This standard is one of a series of European Standards for technical delivery conditions for castings. The other standards in this series are: EN 1559-1, Founding Technical conditions of delivery Part 1: General EN 1559-2, Founding Technica

17、l conditions of delivery Part 2: Additional requirements for steel castings EN 1559-3, Founding Technical conditions of delivery Part 3: Additional requirements for iron castings EN 1559-4, Founding Technical conditions of delivery Part 4: Additional requirements for aluminium alloy castings EN 1559

18、-6, Founding Technical conditions of delivery Part 6: Additional requirements for zinc alloy castings According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,

19、 Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey a

20、nd the United Kingdom. BS EN 1559-5:2017EN 1559-5:2017 (E) 4 Introduction CEN/TC 190 “Foundry Technology” has prepared material standards covering magnesium alloy castings. In order to assist manufacturers and purchasers to prepare proper contractual arrangements and prevent misunderstanding, CEN/TC

21、 190 approved the preparation of a series of standards covering technical delivery conditions. These have been prepared as separate parts. This part of EN 1559 covers the additional technical delivery conditions for magnesium alloy castings, e.g. optional information, manufacturing process, addition

22、al requirements regarding the condition of the casting and test methods. This part of EN 1559 cannot be used alone for compiling a specification for ordering and supplying magnesium alloy castings, but as a complement to EN 1559-1. The clauses marked with a single dot indicate that the requirements

23、of the same clauses of EN 1559-1 have to be met. BS EN 1559-5:2017EN 1559-5:2017 (E) 5 1 Scope This part of EN 1559 specifies the additional technical delivery conditions for castings (see EN 1753) and cast anodes (see EN 12438) made from magnesium alloys. This part of EN 1559 applies to magnesium a

24、lloy castings produced in sand or permanent moulds or by pressure die casting, centrifugal casting, continuous casting or investment casting. This part of EN 1559 does not apply to ingots, bars, billets (or other shapes) for further reprocessing, such as re-melting or extrusion. 2 Normative referenc

25、es The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1

26、370, Founding - Examination of surface condition EN 1371-1, Founding - Liquid penetrant testing- Part 1: Sand, gravity die and low pressure die castings EN 1371-2, Founding - Liquid penetrant testing - Part 2: Investment castings EN 1559-1:2011, Founding - Technical conditions of delivery - Part 1:

27、General EN 1753, Magnesium and magnesium alloys - Magnesium alloy ingots and castings EN 1754, Magnesium and magnesium alloys - Designation system for anodes, ingots and castings - Material symbols and material numbers EN 12438, Magnesium and magnesium alloys - Magnesium alloys for cast anodes prEN

28、12681-1, Founding - Radiographic testing - Part 1: Film techniques1prEN 12681-2, Founding - Radiographic testing - Part 2: Techniques with digital detectors2EN ISO 3452-1, Non-destructive testing - Penetrant testing - Part 1: General principles (ISO 3452-1) EN ISO 5579, Non-destructive testing - Rad

29、iographic testing of metallic materials using film and X- or gamma rays - Basic rules (ISO 5579) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 1559-1 and in the applicable material standard apply. 1) In development. 2) In development. BS EN 1559-5:2

30、017EN 1559-5:2017 (E) 6 4 Information to be supplied by the purchaser 4.1 Mandatory information 4.2 Optional information Where applicable, the enquiry and order shall include other details, such as requirements for: a) an as-cast condition; b) special or subsequent heat treatment if required (togeth

31、er with the heat-treatment conditions); c) formation of test units (unless already defined by material specifications, it shall be in accordance with 8.3.1). 4.3 Drawings, patterns and tools 4.4 Information on the mass 4.5 Preliminary sample 4.6 Initial sample 5 Designations The designation of cast

32、magnesium alloys by material number or material symbol shall be in accordance with EN 1754. Both designations describe the magnesium alloys according to their chemical composition. The designation shall be used on the drawings and in the order. To identify the temper (heat treatment condition) and/o

33、r the casting process, the designation shall be supplemented with symbols preceded and separated from each other by a hyphen (-): for tempers as given in EN 1753; for casting processes as given in EN 1753 and EN 12438. For examples of the use of these symbols in conjunction with either the material

34、symbol or material number see Table 1. Table 1 Examples for the designation Designation by Explanation for the supplement number symbol 3.5316 EN-MCMgAl9Zn1(A) without supplement 3.5316-T4 EN-MCMgAl9Zn1(A)-T4 “-T4” specifies the temper (heat treatment condition) 3.5316-F-D EN-MCMgAl9Zn1(A)-F-D “-F-D

35、” specifies the temper and the casting process 3.5130 EN-MAMgMn1 without supplement 3.5130-S EN-MAMgMn1-S “-S” specifies the casting process BS EN 1559-5:2017EN 1559-5:2017 (E) 7 6 Manufacture 6.1 Manufacturing process 7 Requirements 7.1 General 7.2 Material 7.2.1 Chemical composition EN 1559-1 shal

36、l apply with the following addition: Determination of elements not specified in the applicable material standard shall be carried out when agreed between the manufacturer and the purchaser by the time of acceptance of the order. 7.2.2 Mechanical properties 7.2.3 Other properties 7.3 Casting 7.3.1 Ch

37、emical composition 7.3.2 Mechanical properties 7.3.3 Outer and inner conditions (non-destructive testing) 7.3.3.1 The testing shall be performed according to the applicable European Standards as listed in Table 2. Other methods may be agreed between purchaser and manufacturer. Table 2 Test methods T

38、est method Symbol General principles Test conditions Liquid penetrant PT EN ISO 3452-1 EN 13711 EN 13712 Radiographic RT EN ISO 5579 prEN 126811 prEN 126812 7.3.3.2 7.3.3.3 The selection of a non-destructive testing method is dependent on the thickness and material of the casting and the position, o

39、rientation and size of possible discontinuities in the areas to be tested. Different acceptance criteria can be specified for different areas of the same casting. Moreover, for the same area of the casting different acceptance criteria can be specified according to the non-destructive test methods s

40、elected. For all non-destructive testing methods, the acceptance criteria (discontinuity levels) can be graded with increasing number and/or extent of indications. Unless specifically agreed, discontinuities revealed on cast surfaces which are to be machined, are not to be regarded as discontinuitie

41、s, when these discontinuities are totally removed by machining. BS EN 1559-5:2017EN 1559-5:2017 (E) 8 7.3.3.4 If applicable, the roughness of the cast or grinded surface shall be specified in accordance with EN 1370 and shall be subject of an agreement between the manufacturer and the purchaser by t

42、he time of acceptance of the order. 7.3.4 Condition of the casting 7.3.5 Mass of the casting 7.3.6 Additional requirements regarding the condition of the casting 7.3.6.1 In order to eliminate leaks in castings, impregnation procedures may be used after the approval of the purchaser. The impregnation

43、 medium and method, maximum permitted size of discontinuities and retest procedures shall be agreed between the manufacturer and the purchaser. 7.3.6.2 Where appropriate, a macroscopic examination of a suitably prepared section shall be carried out to assess the grain structure and/or structural ina

44、dequacy of a casting to agreed criteria. NOTE Assessment is usually carried out with naked eyes or with an agreed magnification. 7.3.6.3 Where appropriate, a microscopic examination of a suitably prepared section shall be carried out to determine the metallurgical structure of a casting to agreed cr

45、iteria. NOTE 1 Assessment is usually carried out with an agreed magnification and can include the nature, shape and distribution of the structural constituents. NOTE 2 A cooling curve/thermal analysis carried out on a sample of liquid alloy before casting can help to predict the metallurgical struct

46、ure of the casting. 7.3.6.4 If applicable, density evaluation by weighting in air and water to agreed criteria shall be used to estimate the soundness of the casting. 8 Inspection 8.1 General 8.2 Type of inspection documents and type of inspection The requirements given in the applicable material st

47、andard shall also apply. 8.3 Test unit 8.3.1 Formation of test units 8.3.2 Size of test units The requirements given in the applicable material standard shall also apply. 8.3.3 Inspection frequency When tests are required, unless otherwise agreed, one test per unit shall be carried out. For hardness

48、 testing, the frequency of testing shall be subject to an agreement between the manufacturer and the purchaser. 8.4 Samples The requirements given in the applicable material standard shall also apply. BS EN 1559-5:2017EN 1559-5:2017 (E) 9 8.5 Test procedures The requirements given in the applicable

49、material standard shall also apply. 8.6 Invalidation of test results 8.7 Retests 8.7.1 General 8.7.2 Non-sequential tests (individual values) EN 1559-1 shall apply with the following addition: If there is disagreement between the manufacturer and the purchaser on the chemical composition of a test unit, the manufacturer shall re-check the chemical composition on the original test piece, whenever possible. If disagreement persists a referee analysis shall be car