DLA MS75020 REV F-2013 CONNECTOR PLUG ELECTRICAL - 12 CONTACT INTERVEHICULAR 28 VOLT WATERPROOF.pdf

《DLA MS75020 REV F-2013 CONNECTOR PLUG ELECTRICAL - 12 CONTACT INTERVEHICULAR 28 VOLT WATERPROOF.pdf》由会员分享，可在线阅读，更多相关《DLA MS75020 REV F-2013 CONNECTOR PLUG ELECTRICAL - 12 CONTACT INTERVEHICULAR 28 VOLT WATERPROOF.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 5935 MS75020F 5 September 2013 SUPERSEDING MS75020E 12 December 1979 DETAIL SPECIFICATION SHEET CONNECTOR, PLUG, ELECTRICAL, - 12 CONTACT, INTERVEHICULAR, 28 VOLT, WATERPROOF This specification is approved for use by all Departments and Agencies of the Department of Defense. The requir

2、ements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-38159. FIGURE 1. Connector, plug, electrical, intervehicular. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS75020F 2 Inches mm .960

3、 24.38 2.338 59.39 2.625 66.68 4.9 124.46 5.875 149.23 NOTES: 1. Dimension are in inches, metric equivalents are given for information only. 2. Details of this assembly shall be in accordance with drawings referenced herein and may be obtained online from www.tacom.army.mil or from US Army Tank Auto

4、motive Command, 6501 E. 11 Mile Rd. Warren, MI 48397-5000. 3. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements and promotes economically advantageous lif

5、e cycle. 4. International standardization agreement implementation. This specification implements QSTAG 327 and STANAG 4007. When amendment, revision, or cancellation of this specification is proposed, the preparing activity must coordinate the action with the U.S. National Point of Contact for the

6、international standardization agreement, as identified in the ASSIST database at http:/assist.dla.mil/. FIGURE 1. Connector, plug, electrical, intervehicular Continued. Requirements: Mating receptacle: These plugs mate with receptacles specified in MS75021. This drawing illustrates final assembly. T

7、he parts to be shipped unassembled in bag. Electrical requirements shall be in accordance with Army drawing 10911317. Marking shall consist of the MS PIN and manufacturer identification in accordance with MIL-STD-130. Part or Identifying Number (PIN): See table I. TABLE I. PIN information. PIN Type

8、Body assembly Army PIN Insert Army PIN Contact Army PIN MS75020-1 Pin 8724316 8701274 7716521 MS75020-2 Socket 8701275 7716520 Changes from previous issues. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Provi

9、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS75020F 3 Referenced documents. In addition to MIL-DTL-38159 this document references the following: MS75021 MIL-STD-130 Army drawing 10911317 Army drawing 7769045 QSTAG 327 STANAG 4007 CONCLUDING MATERIAL

10、Custodians: Preparing activity: Army AT DLA - CC Navy - YD Air Force - 85 (Project 5935-2012-241) DLA - CC Review activities: Army - MI Navy MC, SH Air force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-