DLA MS75009 REV J (3)-2008 BRACKET ASSEMBLY RESISTOR (POWER TYPE)《支架总成 电阻(功率型)》.pdf

《DLA MS75009 REV J (3)-2008 BRACKET ASSEMBLY RESISTOR (POWER TYPE)《支架总成 电阻(功率型)》.pdf》由会员分享，可在线阅读，更多相关《DLA MS75009 REV J (3)-2008 BRACKET ASSEMBLY RESISTOR (POWER TYPE)《支架总成 电阻(功率型)》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5905 INCH-POUND MS75009J w/ AMENDMENT 3 8 August 2008 SUPERSEDING MS75009J w/ AMENDMENT 2 8 February 2007 DETAIL SPECIFICATION SHEET BRACKET ASSEMBLY, RESISTOR (POWER TYPE) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requireme

2、nts for acquiring the product described herein shall consist of this specification sheet and the latest issues of MIL-PRF-26, and MIL-R-19365. FIGURE 1. Bracket assembly. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS75009J w/ AMENDMENT 3 2 Assem

3、bly dash no. 1/ Resistor style Dash number or MS part or identifying number (PIN) Spec MIL-PRF-26 Spec MIL-R-19365 Mica washer Centering washer Flat washer Mounting bracket Pan head machine screw 2/ Part No. 3/ Dash No. Part No. Dash No. -29 RW29 RX29 -1 MS15795 -807 -7 MS51957 4/ -55 -30 RW30 -2 -7

4、 MS51957 4/ -52 -31 RW31 -2 -7 MS51957 4/ -54 -32 RW32 RX32 -2 -7 MS51957 4/ -56 -33 RW33 RX33 -2 -7 MS75009 -18 -34 RW34 -3 -5 -8 MS75009 -18 -35 RW35 RX35 -3 -5 -8 MS75009 -19 -36 RW36 RX36 -4 -6 -9 MS75009 -19 -37 RW37 RX37 -4 -6 -9 MS75009 -20 -38 RW38 RX38 -4 -6 -9 MS75009 -21 -39 RW39 -4 -6 -9

5、 MS75009 -23 -47 RW47 RX47 -4 -6 -9 MS75009 -22 Assembly dash no. 1/ Resistor style Dash number or MS part or identifying number (PIN) Spec MIL-PRF-26 Spec MIL-R-19365 Threaded rod 2/ Hexagonal nut Lock washer 5/ Corrosion resisting steel Phosphor bronze Part No. Dash No. Part No. 6/ Dash No. Part N

6、o. 7/ Dash No. -29 RW29 RX29 MS35649 -284 MS35338 -137 or -156 -16 -30 RW30 MS35338 -16 -31 RW31 MS35338 -16 -32 RW32 RX32 MS35338 -16 -33 RW33 RX33 MS75009 -10 MS35338 -16 -34 RW34 MS75009 -10 MS35338 -138 or -157 -17 -35 RW35 RX35 MS75009 -11 MS35650 -304 MS35338 -17 -36 RW36 RX36 MS75009 -11 MS35

7、338 -17 -37 RW37 RX37 MS75009 -12 MS35338 -17 -38 RW38 RX38 MS75009 -13 MS35338 -17 -39 RW39 MS75009 -15 MS35338 -17 -47 RW47 RX47 MS75009 -14 MS35338 -17 1/ The dash number added to the military-specification number constitutes the MS PIN of the assembly. The dash number is derived from the style n

8、umber of the resistor; for example, MS75009-29 is derived from RW29 and RX29. 2/ Use of either pan head machine screw or threaded rod optional, where applicable. 3/ Specification number is NASM15795 4/ Specification number is MS51957 5/ Use of either corrosion-resisting-steel or phosphor-bronze lock

9、 washer(s) is optional. 6/ Specification numbers are NASM35649 or NASM35650. 7/ Specification number is NASM35338. NOTES: 1. Referenced documents shall be of the issue in effect on date of invitations for bid. 2. For design feature purposes, this specification sheet takes precedence over acquisition

10、 documents referenced herein. FIGURE 1. Bracket assembly - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS75009J w/ AMENDMENT 3 3 Inches mm Inches mm Inches mm Inches mm Inches mm .015 .38 .094 2.39 .469 11.91 .688 17.48 1.000 25.40 .03

11、1 .79 .195 4.95 .500 12.70 .750 19.05 1.375 34.93 Dash No. 1/ Mica washer dimension A +.015 -.000 B +.015 -.000 -1 .469 .195 -2 .750 .195 -3 1.000 .500 -4 1.375 .688 1/ The dash number added to the military specification number constitutes the MS PIN; for example: MS75009-1. NOTES 1. Dimensions are

12、in inches. The washer may consist of several sheets to obtain minimum thickness. 2. Metric equivalents are given for general information only. 3. Referenced documents shall be of the issue in effect on date of invitations for bid. 4. For design feature purposes, this specification sheet takes preced

13、ence over acquisition documents referenced herein. FIGURE 2. Mica washer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS75009J w/ AMENDMENT 3 4 Inches mm Inches mm Inches mm Inches mm Inches mm .010 0.25 .045 1.14 .156 3.96 .463 11.76 .750 19.06

14、.031 0.79 125 3.18 .250 6.35 .684 17.37 1.125 25.58 Dash no. 1/ Type Centering washer dimension A B C -5 Cup .750 .463 +.005 -.000 .156 -6 Eared 1.125 .684 .250 .032 1/ The dash number added to the MS military specification number constitutes the MS part number; for example: MS75009-1. NOTE: 1. Dime

15、nsions are in inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerance is 0.010 (0.25 mm) on decimals. 3. Centering washer shall be steel conforming to QQ-S-698, ASTM-A109/A109M, ASTM A1008/A1008M, or SAE-AMS5040, respectively. 4. Referenced documen

16、ts shall be of the issue in effect on date of invitations for bid. 5. For design feature purposes, this specification sheet takes precedence over acquisition documents referenced herein. FIGURE 3. Centering washer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

17、from IHS-,-,-MS75009J w/ AMENDMENT 3 5 Inch mm Inch mm Inch mm Inch mm Inch mm .031 0.79 .281 7.14 .562 14.27 1.000 25.40 1.500 38.10 .062 1.57 .438 11.13 .750 19.05 1.25 31.75 1.750 44.43 .219 5.56 .500 12.70 .875 22.23 1.375 34.93 2.125 53.98 Dash no. 1/ Mounting bracket dimensions A .062 B .062 C

18、 .062 D .062 E .031 F .062 -7 .500 .750 1.00 .438 .219 1.375 -8 .750 .750 1.250 .438 .219 1.750 -9 1.250 .875 1.500 .562 .281 2.125 1/ The dash number added to the military-specification number constitutes the MS PIN; for example: MS75009-1. NOTES 1. Dimensions are in inches. Metric equivalents are

19、given for general information only. 2. Unless otherwise specified, tolerance is 0.005 (0.13 mm) on decimals. 3. Mounting bracket shall be steel conforming to QQ-S-698, ASTM-A109/A109M, ASTM A1008/A1008M, or SAE-AMS5040, respectively. 4. Referenced documents shall be of the issue in effect on date of

20、 invitations for bid. 5. For design feature purposes, this specification sheet takes precedence over acquisition documents referenced herein. FIGURE 4. Mounting bracket. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS75009J w/ AMENDMENT 3 6 Pan he

21、ad machine screw dash no. 1/ Threaded rod dash no. 1/ Dimensions L 2/ (approx) Screw thread Screw Rod -18 -10 3.750 4.250 .164-32 UNC-2A (number 8) -19 -11 4.760 5.250 .190-32 UNF-2A (number 10) -20 -12 6.750 7.250 -21 -13 8.750 9.250 -22 -14 11.250 11.750 -23 -15 12.750 13.250 1/ The dash number ad

22、ded to the military-specification number constitutes the MS PIN; for example: MS75009-1. 2/ When assembled, not less than 1.5 threads nor more than 0.38 inch of thread shall extend beyond each nut. NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. Unle

23、ss otherwise specified, tolerance is 0.005 (0.13 mm) on decimals. 3. Pan Head machine screws not covered by MS51957 and threaded rods shall be carbon-steel ire or carbon steel conforming to ASTM-A108, ASTM-A575, ASTM-A576, ASTM-A1008/A1008M, or ASTM-A675, respectively. 4. Threaded parts shall be in

24、accordance with FED-STD-H28. 5. Referenced documents shall be of the issue in effect on date of invitations for bid. 6. For design feature purposes, this specification sheet takes precedence over acquisition documents referenced herein. FIGURE 5. Rods. Inch mm .38 9.53 1.75 44.45 3.75 95.25 4.25 107

25、.95 4.75 120.65 5.25 133.35 6.75 171.45 7.25 184.13 8.75 222.23 9.25 234.45 11.25 285.75 11.75 298.45 12.75 323.85 13.25 336.55 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS75009J w/ AMENDMENT 3 7 Inch mm Inch mm Inch mm Inch mm Inch mm .040 1.0

26、2 .055 1.40 .168 4.27 .194 4.93 .337 8.56 .046 1.17 .062 1.57 .178 4.52 .205 5.21 .047 1.19 .164 4.17 .190 4.83 .296 7.52 Dash No. 1/ Nominal size Phosphor-bronze-lockwasher dimensions A B C =T+t 2 W Max Min Max Max Min Min -16 No. 8 .164 .178 .168 .296 .046 .040 .055 -17 No. 10 .190 .205 .194 .337

27、.053 .047 .062 1/ The dash number added to the military-specification number constitutes the MS PIN; for example: MS75009-1. NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerance is 0.005 (0.13 mm) on decimals. 3. Refe

28、renced documents shall be of the issue in effect on date of invitations for bid. 4. For design feature purposes, this specification sheet takes precedence over acquisition documents referenced herein. FIGURE 6. Lockwasher. Provided by IHSNot for ResaleNo reproduction or networking permitted without

29、license from IHS-,-,-MS75009J w/ AMENDMENT 3 8 Environmentally preferable material. Environmentally preferable materials should be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmentally Protection Agency (EPA) i

30、s focusing efforts on reducing 31 priority chemicals. The list of chemicals is available on their website at http:/www.epa.gov/epaoswer/hazwaste/minimize/chemlist.htm. Further information is available at the following EPA site: http:/www.epa.gov/epaoswer/hazwaste/minimize/. Included in the EPA list

31、of 31 priority chemicals are cadmium, lead, and mercury. Use of the materials on the list should be minimized or eliminated unless needed to meet the requirements specified herein. Amendment notations. The margins of this specification are marked with vertical lines to indicate modifications generat

32、ed by this amendment. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations

33、. Reference documents. This document references the following: Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5905-2008-052) DLA - CC Review activities: Army - AR Navy - AS, MC, OS NOTE: The activities listed above were interested in this document as of the date

34、 of this document, since organization and responsibilities can change; you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. MIL-PRF-26 SAE-AMS5040 MIL-R-19365 ASTM-A108 NASM15795 ASTM-A109/A109M MS51957 ASTM A1008/A1008M QQ-S-698 ASTM-A575 FED-STD-H28 ASTM-A576 ASTM-A663/A663M NASM 35338 ASTM-A675/A675M NASM 35649 NASM 35650 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-