EN 13757-6-2015 en Communication systems for meters - Part 6 Local Bus《仪表通信系统 第6部分 局域总线》.pdf

《EN 13757-6-2015 en Communication systems for meters - Part 6 Local Bus《仪表通信系统 第6部分 局域总线》.pdf》由会员分享，可在线阅读，更多相关《EN 13757-6-2015 en Communication systems for meters - Part 6 Local Bus《仪表通信系统 第6部分 局域总线》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationCommunication systems for metersPart 6: Local BusBS EN 13757-6:2015National forewordThis British Standard is the UK implementation of EN 13757-6:2015.It supersedes BS EN 13757-6:2008 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommitt

2、ee PEL/894, Remote Meter Reading.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Instituti

3、on 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 89233 2ICS 33.200; 35.100.10; 35.100.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 December 20

4、15.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 13757-6:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13757-6 December 2015 ICS 33.200; 35.100.10; 35.100.20 Supersedes EN 13757-6:2008English Version Communication systems for meters - Part 6: Local

5、Bus Systmes de communication pour compteurs - Partie 6: Bus local Kommunikationssysteme fr Zhler - Teil 6: Lokales Bussystem This European Standard was approved by CEN on 27 September 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for g

6、iving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three o

7、fficial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies

8、 of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spai

9、n, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide

10、for CEN national Members. Ref. No. EN 13757-6:2015 EBS EN 13757-6:2015EN 13757-6:2015 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Physical Layer Specifications 5 Annex A (informative) Schematic implementation of a meter interface . 7 Bibliography 8 B

11、S EN 13757-6:2015EN 13757-6:2015 (E) 3 European foreword This document (EN 13757-6:2015) has been prepared by Technical Committee CEN/TC 294 “Communication systems for meters”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by

12、 publication of an identical text or by endorsement, at the latest by June 2016, and conflicting national standards shall be withdrawn at the latest by June 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC

13、shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13757-6:2008. The following significant editorial changes compared to the previous edition have been incorporated in this European Standard: a) update of the standards title; and b) update of nor

14、mative references to EN 13757-2. EN 13757 consists of the following parts, under the general title “Communication systems for meters“: Part 1: Data exchange Part 2: Physical and link layer Part 3: Dedicated application layer Part 4: Wireless meter readout (Radio meter reading for operation in SRD ba

15、nds) Part 5: Wireless M-Bus relaying Part 6: Local Bus According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finl

16、and, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 13757-6:2015EN 13757-6:201

17、5 (E) 4 Introduction This European Standard is part of a series of standards which covers communication systems for meters and remote reading of meters. EN 13757-1 contains generic descriptions and a communication protocol, EN 13757-2 contains the description of the physical and link layer of a univ

18、ersal twisted pair bus system (M-Bus), EN 13757-3 contains higher protocol layers like transport or application layer, EN 13757-4 specifies wireless communication and EN 13757-5 specifies a relaying extension of EN 13757-4. This European Standard can be used with various link and application layers.

19、 Frequently, the application layer of EN 13757-3 (M-Bus) or the DLMS based application layer described in EN 13757-1 is used. An overview of communication systems for meters is given in EN 13757-1, which also contains further definitions. BS EN 13757-6:2015EN 13757-6:2015 (E) 5 1 Scope This European

20、 Standard specifies the physical layer parameters of a local meter readout system (“Local Bus”) for the communication with and the readout of a single meter or a small cluster of meters via a single battery powered readout device (“master”) which can be connected temporarily or stationary for the co

21、mmunication directly to a meter (i.e. local readout) or via a fixed wiring or a small bus (i.e. remote readout). For generic descriptions concerning communication systems for meters and remote reading of meters, refer to EN 13757-1. 2 Normative references The following documents, in whole or in part

22、, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13757-2, Communication systems for meters and re

23、mote reading of meters Part 2: Physical and link layer 3 Physical Layer Specifications The Local Bus is an alternative to the M-Bus. It is restricted to small installations (Mini installation according to EN 13757-2:2004, Annex E.6.1 type E) and optimized for special battery-driven masters. Usually

24、the readout frequency is limited by the meter. The total cable length is limited to 50 m. The Local Bus does not support meter power supply from the bus. Note that this meter interface is not compatible with M-Bus masters according to EN 13757-2. To facilitate the meter power management, the master

25、shall switch the bus power on (i.e. enter the master mark send state) not more than 10 s before any meter communication. NOTE Annex A shows a possible circuit diagram for implementing such an interface. A meter equipped with a Local Bus interface shall meet the requirements of Table 1. BS EN 13757-6

26、:2015EN 13757-6:2015 (E) 6 Table 1 Requirements meter Parameter Min. Max. Meter Voltage without damage 50 V Isolation from ground 1 M Meter mark state receive (UAM - 1 V) (IBM + 3 mA) 0,1 s or a step change of UAM 4,8 V IAM + 2 mA Master mark state time before communication 5 s 10 s Max. number of u

27、nit loads (LULs) 6 Max. baud rate 2 400 baud BS EN 13757-6:2015EN 13757-6:2015 (E) 7 Annex A (informative) Schematic implementation of a meter interface Figure A.1 shows an example of a schematic simple implementation of a local bus meter interface. Figure A.1 Schematic implementation of a meter int

28、erface BS EN 13757-6:2015EN 13757-6:2015 (E) 8 Bibliography 1 EN 1434-3, Heat Meters Part 3: Data exchange and interfaces 2 EN 13757-1, Communication systems for meters Part 1: Data exchange 3 EN 13757-3, Communication systems for meters and remote reading of meters Part 3: Dedicated application lay

29、er 4 EN 13757-4, Communication systems for meters and remote reading of meters Part 4: Wireless meter readout (Radio meter reading for operation in SRD bands) 5 EN 13757-5, Communication systems for meters and remote reading of meters Part 5: Wireless relaying BS EN 13757-6:2015This page deliberatel

30、y left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Inst

31、itution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been caref

32、ully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out

33、 more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard cop

34、ies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further infor

35、mation on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standard

36、s developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standa

37、rds when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With u

38、pdates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your busi

39、ness. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person

40、or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in

41、 a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW