EN 13356-2001 en Visibility Accessories for Non-Professional Use - Test Methods and Requirements《非专业用高清晰度组件的试验方法和要求》.pdf

《EN 13356-2001 en Visibility Accessories for Non-Professional Use - Test Methods and Requirements《非专业用高清晰度组件的试验方法和要求》.pdf》由会员分享，可在线阅读，更多相关《EN 13356-2001 en Visibility Accessories for Non-Professional Use - Test Methods and Requirements《非专业用高清晰度组件的试验方法和要求》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Visibility accessories for non-professional use - Test methods and requirements The European Standard EN 13356:2001 has the status of a British Standard ICs 13.340.01 BS EN 13356:ZOOl 0 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 13356:2001 Amd. No.

2、National foreword Date Comments This British Standard is the official English language version of EN 13356:2001. The UK participation in its preparation was entrusted by Technical Committee PH/3, Protective clothing, to Subcommittee PH/3/7, High visibility clothing, visual performance, which has the

3、 responsibility to: - - aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A lis

4、t of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “Internat

5、ional Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue . A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a Br

6、itish Standard does not of itself confer immunity from legal obligations. This British Standard, having been prepared under the direction of the Health and Environment Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 September 2001 Summary of

7、 pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 12, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication O BSI 08-2001 ISBN O 580 38

8、101 3 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM O EN 13356 July 2001 English version Visibility accessories for non-professional use - Test methods and requirements Accessoires de visualisation pour usage non-professionnel - Mthodes dessai et exigences Warn-Zubehr fr den nichtprofessionellen

9、 Bereich - Prfvetfahren und Anforderungen This European Standard was approved by CEN on 4 June 2001. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-

10、to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under

11、the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembou

12、rg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FR NORMUNG COMITE EUROPEEN DE NORMALISATION Management Centre: rue de Stassart, 36 8-1050 Brussels 0 2001 CEN All rights of exploitation in any form and by any

13、 means reserved worldwide for CEN national Members. Ref. No. EN 13356:2001 E EN 13356:2001 (E) Contents O 1 2 3 4 4.1 4.2 5 5.1 5.2 5.3 5.4 5.5 5.6 5.7 6 7 Introduction 4 Scope 4 Normative references 4 Terms and definitions 5 Requirements for accessories 5 General requirements 5 Specific requirement

14、s for different types of accessories 6 Testing 7 General 7 Photometric testing . 8 Abrasion test (brushing) . 8 Washing and dry cleaning test . 9 Low temperature test . 9 High temperature test 9 Exposure to water 9 Marking . 10 Manufacture information for use 10 Annex A(normative) Test method for br

15、ushing according to 5.3 . 11 A.l Apparatus 11 Annex ZA(informative) Clauses of this European Standard addressing essential requirements or other provisions of EU Directives . 12 2 EN 13356:2001 (E) Foreword This European Standard has been prepared by Technical Committee CENKC 162, “Protective clothi

16、ng including hand and arm protection and lifejackets“, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2002, and conflicting national standards sha

17、ll be withdrawn at the latest by January 2002. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). Annex A is normative and contains test method for brushing

18、according to 5.3. For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this standard. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Bel

19、gium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 3 EN 13356:2001 (E) O Introduction This European Standard relates to products primarily intended to be worn or carri

20、ed by individuals to make them more conspicuous to other road users under low light levels. The products rely upon retro-reflection for their performance. The products can be regarded as aids to conspicuity that perform best in circumstances of very low ambient lighting. On lit urban roads, products

21、 conforming to EN 471 : 1994 or EN 1150 are necessary to provide conspicuity. In any circumstance in which the failure of a vehicle driver to become aware of another road user could result in the serious injury or death of that road user, only high conspicuity garments can be recommended for use. Pr

22、oducts conforming to this European Standard have a utility when their movement and retro-reflection attract observers attention. 1 Scope This standard specifies the optical performance requirements for accessories which are to be worn, attached to or carried by people and designed for non-profession

23、al use. Visibility accessories complying with this standard are intended to signal the users presence visually when illuminated by vehicle headlight on dark roads. This standard is not applicable to garments. 2 Normative references This European Standard incorporates by dated or undated reference, p

24、rovisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in

25、it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 471 : 1994 High-visibility warning clothing EN 1150 Protective clothing - Visibility clothing for non-professional use - Test methods and requirements EN IS0 3175

26、: 1995 Textiles - Evaluation of stability to machine dry-cleaning (IS0 31751 995) EN IS0 6330 : 2000 Textiles - Domestic washing and drying procedures for textile testing (IS0 6330:2000) CIE 17.4 :1987 International lighting vocabulary - Chapter 845: Lighting CIE 18.2 : 1983 The basis of physical ph

27、otometry CIE 54 :1982 Retroreflection: Definition and measurement IEC 60068-2-32 Basic environmental testing procedures - Part 2: Tests - Test Ed: Free fall IS0 4675 Rubber- or plastics-coated fabrics - Low-temperature bend test 4 EN 13356:2001 (E) 3 Terms and definitions For the purposes of this st

28、andard the definitions for photometric terms according to CIE 17.4 : 1987, CIE 18.2 : 1983 and CIE 54 : 1982 and the following definitions apply: 3.1 accessory retroreflector to be used as an aid to enhance conspicuity and is a product other than a garment 3.2 type 1 - free hanging accessory an item

29、 suspended from a garment or part of the body which is capable of hanging freely and of being removed by a conscious action NOTE which they are suspended. Type 1 fasteners should be produced CO that if subject to undue force they separate from the garment or body from 3.3 type 2 - removable accessor

30、y an item which is temporarily attached to a garment or on to part of the body and is removable without the aid of tools. Requirements of type 2 reflectors should be specified by Table 2 O 3.4 type 3 - mounted accessory an item manufactured to be permanently aff xed 3.5 flexible accessory accessory

31、capable of being wound around a 25 mm mandrel in all orientations without any visible deformation . _I 3.6 rigid accessory accessory not capable of being wound around a 25 mm mandrel in all orientations without any visible deformation 3.7 orientation sensitive material material having coefficients o

32、f retroreflection that differ by more than 15 % when measured at the two rotation angles E 1 = O“ and = 90“ 4 Requirements for accessories 4.1 General requirements The accessories shall meet requirements of area as well as retroreflection. When mounting the retroreflector on a garment, the area of t

33、he accessory shall be such so that the requirements for the retroreflective value are met. The area of a type 1 - accessory shall be between 15 cm2 and 50 cm2 per side. If the type 1 - accessory is only retroreflec- tive from two sides the thickness shall be maximum 10 mm. Each type 2- and type 3 -

34、accessory shall exceed the area of 15 cm2. 5 EN 13356:2001 (E) 4.2 Specific requirements for different types of accessories Observation angle a 4.2.1 General Depending on the type of accessories, the requirements below supplement the general requirements in 4.1. Entrance angle Bi = O“ , = f 10“ 1 =

35、O“ 4.2.2 Photometric requirements The accessories shall achieve the minimum retroreflective values given either in Table 1 or Table 2. 0,2“ (12) 0,33“ (20) 1,5“( 130) Table 1 - Minimum coefficient of luminous intensity R (CIL) for free hanging type 1- accessories 560 350 280 400 250 200 20 10 10 Ent

36、rance angle (Measurement only + entrance angle pi) 1 = + 20“ Observation angle a 1 = + 5“ 2= O“ 2 = O“ 0,2“ (1 2) 110 80 0,33“ (20) 80 60 - 1,5“( 1 “30) 4 3 ,=f20“ I I32 = O“ I 2= I5“ I 1 in mcd/lx O Table 2 - Minimum coefficients of specific retroreflection value R for type 2 and type 3 - accessori

37、es retrorefelective value R in cdlx m* The minimum area for type 2 and type 3 accessories shall meet the minimum CIL value R = 400 mcdtx in all directions around the person at a = 0,33“, 1 = + 5“. 4.2.3 Abrasion resistance (brushing resistance) After testing in accordance with 5.3, the photometric r

38、equirements given in Table 1 or Table 2 shall be met. O 4.2.4 Washing and dry cleaning requirements After testing in accordance with 5.4.2 or 5.4.3, the photometric requirements given in Table 1 or Table 2 shall be met. 6 EN 13356:2001 (E) Exposure 5.3 Abrasion test (brushing) 5.5.2 Free fall test (

39、according to 5.6 High temperature test 5.7.1 Influence of water (water 5.7.2 Influence of rainfall (Type 3) 5.2 Photometric testing IEC 60068-2-32) immersion) 4.2.5 Durability against heat After testing in accordance with 5.6, the photometric requirements given in Table 1 or Table 2 shall be met. Te

40、st sample 1 2 3 4 X X X X X X X“ X X X X X X 4.2.6 Low temperature requirements (folding) After testing in accordance with 5.5.1, the photometric requirements given in Table 1 or Table 2 shall be met. 4.2.7 Exposure to water After testing in accordance with 5.7.1, the photometric requirements given

41、in Table 1 or Table 2 shall be met and no visible water penetration is allowed. 4.2.8 Influence of rainfall During the test in accordance with 5.7.2, the photometric requirements given in Table 1 or 2 shall be met at the entrance angle Bi= + 5“ and 2= O“ and the observation angle CL is 0,2“. If mate

42、rial is orientation sensitive when dry, measurements shall be made at the rotation angle which gave the lowest measured performance when dry. O 5 Testing 5.1 General The samples tested in accordance with 5.2 shall be exposed as specified in Table 3 and Table 4 depending on the types of accessories.

43、After exposure each test specimen shall fulfil the photometric requirements given in Table 1 for type 1 accessories or Table 2 for type 2 and type 3 accessories (at the entrance angle pi = +5“ and 2 = O“ and observations angle CL = 0,2“). Preconditioning in accordance with EN 471 : 1994. I a for typ

44、e 1 only I 7 EN 13356:2001 (E) Exposure Table 4 - Test exposure for flexible accessories Test sample 5.2 Photometric testing 5.2.1 Principle The performance of the accessories shall be determined by the procedures given in CIE 54 : 1982. 5.2.2 Mounting of sample The sample shall be mounted to a goni

45、ometer table in the position which is intended to be wom by the user. If it is not possible to define this position, the retroreflector shall be tested at the most unfavourable rotation angle determined when measured at a = 0,33“ and pi = + 5“. Type 3 accessory shall be applied in form of a test sam

46、ple of minimum size of 25 cm2. 5.2.3 Conditioning The sample shall be conditioned for at least 24 h at a temperature of (23 * 2)“C and a relative humidity of (50 * 5)%. 5.3 Abrasion test (brushing) The test shall be carried out with a polyamide brush with size according to annex A. The brush is of a

47、 PA 6.6 quality with diameter (0,25 * 0,025) mm, arranged in 56 sections with each (165 * 5) stems. The length of the stems shall be (14 f 1) mm. The total brush shall weigh (450 * 5) g. The brush shall be mounted in a machine which provides a back and forth going movement in one dimension. The test

48、 sample is mounted horizontally. The direction of the movement shall be transverse the length of the brush. The brush shall be moved back and forth (30 * 3) timedmin for 10 min. The change of the direction of the brush shall be outside of the sample area. a i EN 13356:2001 (E) 5.4 Washing and dry cl

49、eaning test 5.4.1 General The accessory shall be mounted as intended on a sample of background fabric 400 mm x 400 mm, per instructions from the manufacturer. In case of tapes with a width of less than 100 mm several are placed next to each Fther. The background fabric shall be of 65 % polyester and 35 % cotton with an area weight of 230 g/m2 to 250 g/m . The test sample shall be washed or dry cleaned 5 times, according to the manufacturers instruction. 5.4.2 Washing The samples shall be washed in accordance with Method 5A of EN IS0 6330 : 2000, and drie