EN 12816-2010 en LPG equipment and accessories - Transportable refillable LPG cylinders - Disposal《液化石油气(LPG)设备和配件 可运输可再充填钢 铝液化石油气(LPG)瓶》.pdf

《EN 12816-2010 en LPG equipment and accessories - Transportable refillable LPG cylinders - Disposal《液化石油气(LPG)设备和配件 可运输可再充填钢 铝液化石油气(LPG)瓶》.pdf》由会员分享，可在线阅读，更多相关《EN 12816-2010 en LPG equipment and accessories - Transportable refillable LPG cylinders - Disposal《液化石油气(LPG)设备和配件 可运输可再充填钢 铝液化石油气(LPG)瓶》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 12816:2010LPG equipment and accessories Transportable refillable LPGcylinders DisposalBS EN 12816:2010 BRITISH STANDARDNational forewordThis British Standard is the UK impl

2、ementation of EN 12816:2010. Itsupersedes BS EN 12816:2001 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PVE/19, LPG containers and their associated fittings.A list of organizations represented on this committee can beobtained on request to its secret

3、ary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 67235 4ICS 13.030.50; 23.020.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard wa

4、s published under the authority of theStandards Policy and Strategy Committee on 31 January 2011.Amendments issued since publicationDate Text affectedBS EN 12816:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12816 December 2010 ICS 13.030.50; 23.020.30 Supersedes EN 12816:2001English Vers

5、ion LPG equipment and accessories - Transportable refillable LPG cylinders - Disposal quipements et accessoires pour GPL - Bouteilles transportables et rechargeables pour GPL - limination Flssiggas-Gerte und Ausrstungsteile - Ortsbewegliche wiederbefllbare Flaschen fr Flssiggas (LPG) - Entsorgung Th

6、is European Standard was approved by CEN on 20 November 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical refe

7、rences concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CE

8、N member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ic

9、eland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Aven

10、ue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12816:2010: EBS EN 12816:2010EN 12816:2010 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Normative references 53 Terms and definitions .54

11、 Gas freeing of cylinders 65 Disposal of cylinders .6Annex A (informative) Environmental checklist .8Bibliography 9BS EN 12816:2010EN 12816:2010 (E) 3 Foreword This document (EN 12816:2010) has been prepared by Technical Committee CEN/TC 286 “Liquefied petroleum gas equipment and accessories”, the s

12、ecretariat of which is held by NSAI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2011, and conflicting national standards shall be withdrawn at the latest by June 2011. Attention is drawn

13、 to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12816:2001. The main technical changes in this revision are the: inclusion o

14、f cylinders manufactured from composite materials and aluminium; addition of an environmental checklist Annex A. Users of this standard, prepared in the field of application of Article 118A of the EC Treaty, should be aware that standards have no formal legal relationship with Directives that may ha

15、ve been made under Article 118A of the Treaty. In addition, national legislation in the Member states may contain more stringent requirements than the minimum requirements of a Directive based on Article 118A. Information on the relationship between the national legislation implementing Directives b

16、ased on Article 118A and this EN may be given in a national foreword of the national standard implementing this standard EN. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belg

17、ium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 128

18、16:2010EN 12816:2010 (E) 4 Introduction This European Standard specifies a method for safe handling and disposal of refillable LPG cylinders, of water capacity 0,5 litres up to and including 150 litres, that have been received into filling/maintenance/requalification plants from customers, waste col

19、lection depots, etc. This European Standard calls for the use of substances and procedures that may be injurious to health and/or environment if adequate precautions are not taken. It refers only to technical suitability and does not absolve the user from legal obligations relating to health, safety

20、 and environmental protection at any stage. Protection of the environment is a key political issue in Europe and elsewhere. Protection of the environment is taken in a very broad sense. The standard takes into consideration the total lifecycle aspects of the activities involved in complying with the

21、 standard. These activities include all phases such as scrapping, recycling of materials, etc. It has been assumed in the drafting of this European Standard that execution of its provisions is entrusted to appropriately qualified and experienced people. BS EN 12816:2010EN 12816:2010 (E) 5 1 Scope Th

22、is European Standard specifies methods for the safe gas freeing and disposal of refillable LPG cylinders manufactured from steel, composite materials and aluminium, of water capacity 0,5 litres up to and including 150 litres. This European Standard is applicable to the following: welded and brazed s

23、teel LPG cylinders with a specified minimum wall thickness (see EN 1442 and EN 12807 or equivalent standard); welded steel LPG cylinders without specified minimum wall thickness (see EN 14140 or equivalent standard); welded aluminium LPG cylinders (see EN 13110 or equivalent standard); composite LPG

24、 cylinders (see EN 14427 or equivalent standard). This European Standard is intended to be applied to cylinders complying with ADR (including pi marked cylinders) and also to existing non ADR cylinder populations. 2 Normative references The following referenced documents are indispensable for the ap

25、plication of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 14912, LPG equipment and accessories Inspection and maintenance of LPG cylinder valves at time of pe

26、riodic inspection of cylinders 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 liquefied petroleum gas LPG mixture of predominantly butane or propane with traces of other hydrocarbon gases classified in accordance with UN number 1965, hydroca

27、rbon gases mixture, liquefied, NOS or UN number 1075, petroleum gases, liquefied NOTE In some countries, UN numbers 1011 and 1978 may also be designated LPG. 3.2 gas free with an LPG concentration in air less than 20 % of the lower explosive limit 3.3 disposal discarding of LPG cylinders in the form

28、 of scrap material after gas freeing 3.4 cylinder disposer organisation responsible for disposal of an LPG cylinder BS EN 12816:2010EN 12816:2010 (E) 6 3.5 purging displacing LPG with a non-flammable gas, steam or water 3.6 evacuation removal of the LPG from the cylinder by the use of a vacuum 4 Gas

29、 freeing of cylinders 4.1 Cylinder disposers shall remove LPG from cylinders by: returning to an LPG storage tank via a suitably designed pump/compressor system, or flaring through a purpose designed flare stack fitted with a flame arrestor as required, or venting through a purpose designed high lev

30、el vent, in a controlled manner, that ensures that the vented gas is diluted to less than 20 % of the lower explosive limit before it reaches ground level, or any potential source of ignition, or a combination of any of these options. For safety and environmental protection reasons the first option

31、is preferable. However it is recommended that, at a minimum, the liquid contents of cylinders should always be returned to an LPG storage tank. 4.2 Equipment used for removal of LPG shall be capable of removing liquid LPG from any cylinder however full. It should also be capable of removing LPG vapo

32、ur so that the internal pressure is reduced to atmospheric. 4.3 Cylinders shall be made gas free by a safe means, for example: evacuation, or purging. NOTE 1 Where water is the purging fluid, waste water should be recycled where possible for further purging applications. NOTE 2 Where possible, the r

33、ecovery of the gas should be maximised in a closed loop system and stored for re-use. 4.4 Any flammable liquids remaining in the cylinder (e.g. oily residues) shall be removed and disposed of in a suitable manner before the cylinder can be considered gas free. 4.5 Cylinders shall be checked to ensur

34、e that they are depressurised and gas free prior to disposal. 4.6 Valves and other fittings shall be: scrapped and recycled, or inspected/reconditioned in accordance with EN 14912 for re-use. 5 Disposal of cylinders 5.1 Disposal shall only take place after a cylinder is made gas free and the cylinde

35、r valve has been removed. 5.2 Cylinders shall be made unserviceable for storing LPG by any of the following methods: BS EN 12816:2010EN 12816:2010 (E) 7 mechanical crushing; mechanical shredding; piercing holes of 50 mm diameter or more, in at least two places; irregular cutting of the neck of the c

36、ylinder; irregular cutting of the body of the cylinder, into two or more pieces. NOTE Noise levels from the above methods should be evaluated and measures put in place to minimise the impact upon the external environment. 5.3 Cylinders made unserviceable in accordance with 5.2 shall be considered as

37、 scrap material for disposal and recycled in order to maximise the re-use of scrap material and minimise the total energy life cycle of the cylinders. The cylinder disposer shall endeavour to minimise wastage of material by selecting the most appropriate scrapping method. NOTE Any coatings on cylind

38、ers may affect recycling methods and should be taken into account. 5.4 Composite cylinders shall be disposed of in accordance with the manufacturers instructions, e.g. the recycling of thermoplastic parts and metallic liners, the grinding of thermoset parts. BS EN 12816:2010EN 12816:2010 (E) 8 Annex

39、 A (informative) Environmental checklist Environmental Aspect Stages of the life cycle All stages Acquisition Production Use End-of-Life Raw materials and energy Pre-manufactured materialsandcomponentsProductionPackagingUse MaintenanceandrepairUse of additionalproductsReuse /Materialand Energy Recov

40、ery Incinerationwithoutenergy recovery DepositionTransportationInputs Materials 4.6 5.3 5.4 Water 4.3 Energy 4.1 4.3 5.3 5.4 Land Outputs Emissions to air 4.1 4.2 4.5 4.1 Discharges to water Discharges to soil Waste 4.1 4.4 4.6 5.2 5.3 5.4 Noise, vibration, radiation, heat losses 5.2 Other relevant

41、aspects Risk to the environment from accidents or unintended use Intro Customer information 5.4 Comments: BS EN 12816:2010EN 12816:2010 (E) 9 Bibliography 1 EN 1442, LPG equipment and accessories Transportable refillable welded steel cylinders for LPG Design and construction 2 EN 12807, LPG equipmen

42、t and accessories Transportable refillable brazed steel cylinders for liquefied petroleum gas (LPG) Design and construction 3 EN 13110, Transportable refillable welded aluminium cylinders for liquefied petroleum gas (LPG) Design and construction 4 EN 14140, LPG equipment and accessories Transportabl

43、e refillable welded steel cylinders for LPG Alternative design and construction 5 EN 14427, Transportable refillable fully wrapped composite cylinders for Liquefied Petroleum Gases (LPG) Design and Construction 6 ADR, European Agreement concerning the International Carriage of Dangerous Goods by Roa

44、d This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is

45、 incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they

46、possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the ide

47、ntity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Em

48、ail: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7

49、001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge