EN 12613-2009 en Plastics warning devices for underground cables and pipelines with visual characteristics《具有可视特性的地下电缆和管线用塑料报警装置》.pdf

《EN 12613-2009 en Plastics warning devices for underground cables and pipelines with visual characteristics《具有可视特性的地下电缆和管线用塑料报警装置》.pdf》由会员分享，可在线阅读，更多相关《EN 12613-2009 en Plastics warning devices for underground cables and pipelines with visual characteristics《具有可视特性的地下电缆和管线用塑料报警装置》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 12613:2009Incorporating Corrigendum September 2009ICS 13.320; 83.140.99NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDPlastics warning devices for underground cables and pipelines with visual characteristicsThis British Standard was published under the au

2、thority of the Standards Policy and Strategy Committee on 31 August 2009 BSI 2009ISBN 978 0 580 68998 7Amendments/corrigenda issued since publicationDate CommentsBS EN 12613:2009National forewordThis British Standard is the UK implementation of EN 12613:2009. Itsupersedes BS EN 12613:2001 which is w

3、ithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/88, Plastics piping systems.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract

4、. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunityfrom legal obligations.30 September 2009 Correction to CEN supersession BS EN 12613:2009EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORMEN 12613June 2009ICS 13.320; 83.140.99 Supersedes EN

5、12613:2001 English VersionPlastics warning devices for underground cables and pipelines with visual characteristicsDispositifs avertisseurs caractristiques visuelles, en matire plastique, pour cbles et canalisations enterrsWarneinrichtungen aus Kunststoff mit visuellen Eigenschaften fr erdverlegte K

6、abel und RohrleitungenThis European Standard was approved by CEN on 20 May 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bi

7、bliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibilit

8、y of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ir

9、eland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 1

10、7, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Ref. No. EN 12613:2009: EBS EN 12613:2009EN 12613:2009 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Normative references 53 Terms and definitions .54 Material .6

11、5 Requirements .65.1 Colour .65.2 Appearance and colour fastness .65.3 Dimensional characteristics .65.4 Laying characteristics .75.4.1 General 75.4.2 Tensile withstand strength .75.4.3 Transversal rigidity 75.4.4 Flatness 75.5 Visual warning characteristics .75.6 Resistance against micro-organisms

12、75.7 Resistance to UV-light .75.8 Temperature stability 85.9 Resistance of printing .85.10 Marking .86 Test methods 86.1 Test pieces and test conditions .86.2 Colour fastness 86.3 Tensile withstand strength .86.3.1 Test pieces .86.3.2 Apparatus .96.3.3 Procedure .96.4 Transversal rigidity 96.5 Flatn

13、ess . 107 Factory production control tests 108 Test report . 11Annex A (normative) Determination of visual warning characteristics by simulation of trench opening 12A.1 Principle . 12A.2 Apparatus 12A.3 Test pieces 16A.4 Conditioning and test temperature . 16A.5 Procedure 16A.6 Test conditions for w

14、arning devices wider than 500 mm . 16Annex B (normative) Chemical resistance to ammonium sulphide . 17B.1 Apparatus 17B.2 Preparation of test pieces 17B.3 Procedure 17BS EN 12613:2009EN 12613:2009 (E) 3 Foreword This document (EN 12613:2009) has been prepared by Technical Committee CEN/TC 249 “Plast

15、ics”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2009, and conflicting national standards shall be withdrawn at the latest by December 2009.

16、Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12613:2001. This document is a revision of EN 12613:2001 w

17、ith the following modifications: review of the test method for assessing the visual characteristics of the warning devices (Annex A) while keeping the principle and the functional features specified in EN 12613:2001; addition of test conditions for assessing the visual characteristics of the warning

18、 devices wider than 500 mm; updating of the normative references; improvement of the subclauses for the laying characteristics; improvement of the subclauses for the resistance against micro-organisms, to UV-light and temperature stability. According to the CEN/CENELEC Internal Regulations, the nati

19、onal standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

20、Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 12613:2009EN 12613:2009 (E) 4 Introduction Visual warning devices are used for the manual or mechanized laying of cables and piping buried in ground such as electrical power cables, communication

21、cables, pressure and non-pressure piping systems. The purpose of warning devices is to warn of the presence of a pipe or a cable, when opening a trench, to indicate its orientation and to identify the equipment protected. The warning devices are expected to last at least the lifetime of the equipmen

22、ts with which they are associated. BS EN 12613:2009EN 12613:2009 (E) 5 1 Scope This European Standard specifies the material, mechanical and functional (fitness for purpose) requirements for warning devices with visual characteristics manufactured from plastics, intended to indicate the presence of

23、cables and piping systems buried in ground when opening trenches and more generally during digging work. This European Standard also specifies the test methods referred to in this document. This European Standard is applicable to two types of visual warning devices: tapes (type 1) and meshes (type 2

24、). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 60898-1:2003, Electr

25、ical accessories Circuit breakers for overcurrent protection for household and similar installations Part 1: Circuit-breakers for a.c. operation (IEC 60898-1:2002, modified) EN ISO 175, Plastics Method of test for determination of the effects of immersion in liquid chemicals (ISO 175:1999) EN ISO 84

26、6, Plastics Evaluation of the action of microorganisms (ISO 846:1997) EN ISO 4892-1, Plastics Methods of exposure to laboratory light sources Part 1: General guidance (ISO 4892-1:1999) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 type 1 wa

27、rning device strip manufactured from plastics to warn of the presence of underground cables or pipes during excavation 3.2 type 2 warning device mesh/net manufactured from plastics to warn of the presence of underground cables or pipes during excavation 3.3 nominal width of a warning device (W0) ove

28、rall width of the warning device, as declared by the manufacturer, in millimetres 3.4 longitudinal direction direction corresponding to the extrusion direction, parallel to the length of the reel 3.5 transversal direction direction parallel to the width (at right angle to the length) BS EN 12613:200

29、9EN 12613:2009 (E) 6 4 Material The material shall be made of any thermoplastic material, e.g. polyethylene (PE) or polypropylene (PP), to which are added those additives necessary for the manufacture of warning devices conforming to the requirements of this standard. The use of own or external repr

30、ocessable materials or recyclable materials shall be permitted for the manufacture of warning devices conforming to the requirements of this standard. The material, additives, colour masterbatches and inks for printing, if added, shall have no detrimental effect on the environment. 5 Requirements 5.

31、1 Colour The colour of the warning device shall be as agreed between the manufacturer and the purchaser. 5.2 Appearance and colour fastness The appearance, colouring and marking of the warning device shall not exhibit any change when tested in accordance with 6.2. No discoloration or change of the i

32、nitial colour shall be permitted. Only a change in surface appearance (e.g. gloss/matt) shall be permitted. For a given type of warning device (design, width), the colour fastness shall be tested for each colour.5.3 Dimensional characteristics The nominal width, W0, of the warning device shall be as

33、 agreed between the manufacturer and the purchaser. For type 1 warning devices, each individual value of the width shall be equal or greater than 50 mm and the outside edges of the warning device shall be straight and parallel. The deviation of each outside edge, towards outside or inside relatively

34、 to the mean line, shall be less or equal to 2 mm. For type 2 warning devices, the dimensional characteristics shall conform to Table 1 and it is recommended that the minimum reel length is equal or greater than 100 m or as agreed between the manufacturer and the purchaser. Table 1 Dimensional chara

35、cteristics Characteristics Unit Requirements Width (W) mm (W0 0,1W0 W W0+ 0,1W0) and W 50 (W0 10 W W0+ 10) W0 100 W0 100 Internal perimeter of an opening mm 360 Strand width mm 1 for an internal perimeter 160 2 for an Internal perimeter 160 BS EN 12613:2009EN 12613:2009 (E) 7 5.4 Laying characterist

36、ics 5.4.1 General For ease of use, the warning devices need sufficient rigidity, flatness and longitudinal mechanical strength to maintain their shape. 5.4.2 Tensile withstand strength When tested in accordance with 6.3, the type 1 warning device shall withstand a load of 200 N during 5 min in the l

37、ongitudinal direction, without starting of the separation of the weak points, if any, and shall not exhibit a reduction of more than 20 % of its width after removal of the load. When tested in accordance with 6.3, the type 2 warning device shall withstand a load of 300 N during 5 min in longitudinal

38、 direction, without starting of the separation of the weak points, if any, and shall not exhibit a reduction of more than 20 % of its width after removal of the load. 5.4.3 Transversal rigidity When tested in accordance with 6.4, the deflection of outsides edges of the warning device shall be less o

39、r equal to W0 /4. If the nominal width of the warning device is greater than 500 mm, this requirement shall not apply. 5.4.4 Flatness When tested in accordance with 6.5, the warning device shall not exhibit at any point a separation with respect to the reference surface greater than W0 /4. 5.5 Visua

40、l warning characteristics The visual characteristics of the warning devices are assessed by means of a test which simulates the opening of a trench with the bucket of an excavator. See A.1. When tested in accordance with Annex A, the warning device shall exhibit at least one single part of a minimum

41、 length of 200 mm outside of the movable plate (which simulates the bucket) and at least one single part of a minimum length of 200 mm in the frame (which simulate the trench). The width of the visible parts of warning device shall be greater or equal to 2 mm. 5.6 Resistance against micro-organisms

42、The resistance against micro-organisms shall be determined only for the warning devices made from materials other than polyethylene (PE) or polypropylene (PP). When tested in accordance with EN ISO 846 and the test conditions as specified by the purchaser, the warning device shall not exhibit any ch

43、ange. 5.7 Resistance to UV-light If required, the warning device shall be resistant to UV-light. When tested in accordance with the guidance provided by EN ISO 4892-1 and its subsequent parts, and the test method and conditions as specified by the purchaser, the warning device shall conform to the r

44、equirement as specified by the purchaser. If the warning device is not resistant to UV-light, it shall be protected by suitable packaging, as agreed between manufacturer and purchaser. BS EN 12613:2009EN 12613:2009 (E) 8 5.8 Temperature stability If required, the temperature stability of the warning

45、 device shall conform to the requirement, as agreed between the manufacturer and the purchaser. 5.9 Resistance of printing If required, the permanence of print (or printing) on the warning device shall be determined in accordance with 9.3 of EN 60898-1:2003 and shall fulfil the requirements specifie

46、d in 9.3 of EN 60898-1:2003. 5.10 Marking The visual warning devices shall be marked at intervals not exceeding 1 m. The marking shall be legible when viewed without magnification, durable and shall include at least the following information: a) name or trademark of the manufacturer; b) year of manu

47、facture in figure or in code; c) reference to this European Standard: EN 12613. Information other than the above shall be in accordance with the purchasers specification. 6 Test methods 6.1 Test pieces and test conditions For each test, the number of warning device test pieces shall be four. When on

48、e of the test pieces does not conform to the test requirement, that test shall be repeated on further four test pieces. In this case, the four test pieces shall be conform to the requirement, to declare the test successful. Unless otherwise specified, testing shall be performed at (23 2) C. 6.2 Colo

49、ur fastness Three separate tests shall be carried out in accordance with: a) Annex B, by immersion in a aqueous solution with 20 % by mass of ammonium sulphide; b) EN ISO 175, by immersion in nitric acid with a concentration of 10 % by mass; c) EN ISO 175, by immersion in a sodium carbonate solution with a concentration of 20 % by mass. 6.3 Tensile wi