EN 12566-4-2016 en Small wastewater treatment systems for up to 50 PT - Part 4 Septic tanks assembled in situ from prefabricated kits《小型废水处理系统可容纳50PT-第4部分 由预制袋就地组装化粪池》.pdf

《EN 12566-4-2016 en Small wastewater treatment systems for up to 50 PT - Part 4 Septic tanks assembled in situ from prefabricated kits《小型废水处理系统可容纳50PT-第4部分 由预制袋就地组装化粪池》.pdf》由会员分享，可在线阅读，更多相关《EN 12566-4-2016 en Small wastewater treatment systems for up to 50 PT - Part 4 Septic tanks assembled in situ from prefabricated kits《小型废水处理系统可容纳50PT-第4部分 由预制袋就地组装化粪池》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 12566-4:2016Small wastewater treatmentsystems for up to 50 PTPart 4: Septic tanks assembled in situ fromprefabricated kitsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 12566-4:2016 BRITISH STANDARDNational forewordThis British Standard is the UK impleme

2、ntation of EN 12566-4:2016.It supersedes BS EN 12566-4:2007 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/505, Wastewater engineering.A list of organizations represented on this committee can beobtained on request to its secretary.This publication d

3、oes not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016. Published by BSI StandardsLimited 2016ISBN 978 0 580 91478 2ICS 13.060.30Compliance with a British Standard cannot confer immunity fromlegal

4、 obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 September 2016.Amendments issued since publicationDate Text affectedBS EN 12566-4:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12566-4 August 2016 ICS 13.060.30 Supers

5、edes EN 12566-4:2007English Version Small wastewater treatment systems for up to 50 PT - Part 4: Septic tanks assembled in situ from prefabricated kits Petites installations de traitement des eaux uses jusqu 50 PTE - Partie 4: Fosses septiques assembles sur site en kit dlments prfabriques Kleinklran

6、lagen fr bis zu 50 EW - Teil 4: Baustze fr vor Ort einzubauende Faulgruben This European Standard was approved by CEN on 25 June 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national s

7、tandard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version i

8、n any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech

9、Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EURO

10、PEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12566-4:2016 EBS

11、 EN 12566-4:2016EN 12566-4:2016 (E) 2 Contents Page European foreword . 4 1 Scope 6 2 Normative references 6 3 Terms and definitions . 6 4 Product characteristics . 7 5 Testing, assessment and sampling methods . 7 6 Assessment and verification of constancy of performance AVCP. 7 6.1 General 7 6.2 Ty

12、pe testing . 7 6.2.1 General 7 6.2.2 Test samples, testing and compliance criteria . 8 6.2.3 Test reports 10 6.2.4 Shared other party results 10 6.2.5 Cascading determination of the product type results 10 6.3 Factory production control 11 6.3.1 General . 11 6.3.2 Requirements 12 6.3.3 Product speci

13、fic requirements 15 6.3.4 Initial inspection of factory and of FPC 15 6.3.5 Continuous surveillance of FPC . 16 6.3.6 Procedure for modifications 16 6.3.7 One-off products, pre-production products (e.g. prototypes) and products produced in very low quantity 16 7 Classification and designation . 17 8

14、 Marking, labelling and packaging 17 8.1 Marking 17 8.2 Installation instructions 17 8.3 Operating and maintenance instructions 18 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation 19 ZA.1 Scope and relevant characteristics

15、19 ZA.2 Procedure of attestation of conformity of prefabricated septic plants 20 ZA.2.1 System(s) of AVCP 20 ZA.2.2 Declaration of performance (DoP) 23 ZA.2.2.1 General. 23 ZA.2.2.2 Content. 23 ZA.2.2.3 Example of DoP . 24 ZA.3 CE marking and labelling 26 BS EN 12566-4:2016EN 12566-4:2016 (E) 3 Bibl

16、iography . 29 BS EN 12566-4:2016EN 12566-4:2016 (E) 4 European foreword This document (EN 12566-4:2016) has been prepared by Technical Committee CEN/TC 165 “Wastewater engineering”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, eith

17、er by publication of an identical text or by endorsement, at the latest by February 2017, and conflicting national standards shall be withdrawn at the latest by May 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or

18、CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12566-4:2007. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Di

19、rective(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. The differences between this version and EN 12566-4:2007 are mainly editorial changes according to the Construction Product Regulation (CPR). The standard series EN 12566 “Small w

20、astewater treatment systems for up to 50 PT” contains the following parts (see Figure 1): Part 1: Prefabricated septic tanks; Part 3: Packaged and/or site assembled domestic wastewater treatment plants; Part 4: Septic tanks assembled in situ from prefabricated kits (this document); Part 6: Prefabric

21、ated treatment unit used for septic tank effluent; Part 7: Prefabricated tertiary treatment unit. For filtration systems, CEN/TC 165 decided to publish the following CEN Technical reports, which are considered as Code of practices and do not specify treatment requirements: Part 2: Soil infiltration

22、systems; Part 5: Pre-treated Effluent Filtration systems. BS EN 12566-4:2016EN 12566-4:2016 (E) 5 Key A domestic wastewater 1 prefabricated septic tank B septic tank effluent 2 soil infiltration system C treated infiltrated effluent 3 packaged and/or site assembled domestic wastewater treatment plan

23、t D treated wastewater 4 septic tank assembled in situ from prefabricated kit E tertiary treated wastewater 5 pre-treated effluent filtration system 6 prefabricated treatment unit used for septic tank effluent 7 prefabricated tertiary treatment unit National regulations may specify different arrange

24、ments between the products described in the standard series EN 12566. Figure 1 Scheme related to the arrangement of the parts of EN 12566 According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard:

25、Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, S

26、weden, Switzerland, Turkey and the United Kingdom. BS EN 12566-4:2016EN 12566-4:2016 (E) 6 1 Scope This European Standard specifies the requirements for septic tanks assembled in situ from prefabricated kits and ancillary equipment where applicable, used outside buildings for the partial treatment o

27、f domestic wastewater for a population up to 50 PT. Pipe sizes, loads, watertightness, marking and evaluation of conformity are specified. This European Standard does not apply to septic tanks receiving grey water only. 2 Normative references The following documents, in whole or in part, are normati

28、vely referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 681-1, Elastomeric seals Materials requirements for pipe join

29、t seals used in water and drainage applications Part 1: Vulcanized rubber EN 12566-1:2016, Small wastewater treatment systems for up to 50 PT Part 1: Prefabricated septic tanks EN 16323:2014, Glossary of wastewater engineering terms 3 Terms and definitions For the purposes of this document, the term

30、s and definitions given in EN 12566-1:2016, EN 16323:2014 and the following apply. 3.1 kit complete set of components provided by a single manufacturer and assembled on its permanent site from a kit in order to form a septic tank 3.2 ancillary equipment pipe connections and internal components that

31、are part of the septic tank kit 3.3 product family group of products in which, for the purpose of evaluation, the selected property(s) is/are similar for all products within the group Note 1 to entry: The definition of family takes into account at least similar shape, equipment, materials and condit

32、ions of end use and ensures the minimum hydraulic efficiency and minimum structural behaviour for all the products in the range. Note 2 to entry: The minimum level of performance (hydraulic efficiency and structural behaviour) are given by the test carried out on one model of the family. BS EN 12566

33、-4:2016EN 12566-4:2016 (E) 7 4 Product characteristics Products according to this standard shall meet the requirements of EN 12566-1:2016, Clause 4. In addition to the specifications of EN 12566-1, elastomeric seals for joints shall conform to EN 681-1, where applicable. Where the product consists o

34、f more than one tank, the evaluation of the structural behaviour of the product family shall be carried out according to EN 12566-1 for each different sized tank. Where the product consists of more than one tank, the hydraulic efficiency test shall be done according to EN 12566-1 after assembling th

35、e tanks. Pipe connections and ancillary equipment shall be in accordance with the relevant standards. Durability is ensured by the product passing the relevant requirements for each essential characteristic, if they represent the state of the art. 5 Testing, assessment and sampling methods Products

36、according to this standard shall be tested according to EN 12566-1:2016, Clause 5 as relevant. 6 Assessment and verification of constancy of performance AVCP 6.1 General The compliance of the septic tank with the requirements of this standard and with the performances declared by the manufacturer in

37、 the DoP shall be demonstrated by: determination of the product type; factory production control by the manufacturer, including product assessment. The manufacturer shall always retain the overall control and shall have the necessary means to take responsibility for the conformity of the product wit

38、h its declared performance(s). 6.2 Type testing 6.2.1 General All performances related to characteristics included in this standard shall be determined when the manufacturer intends to declare the respective performances unless the standard gives provisions for declaring them without performing test

39、s. (e.g. use of previously existing data, CWFT and conventionally accepted performance). Assessment previously performed in accordance with the provisions of this standard, may be taken into account provided that they were made to the same or a more rigorous test method, under the same AVCP system o

40、n the same product or products of similar design, construction and functionality, such that the results are applicable to the product in question. NOTE 1 Same AVCP system means testing by an independent third party, and for reaction to fire under the responsibility of a notified product certificatio

41、n body (only for products covered by system 1+ and 1). For the purposes of assessment, the manufacturers products may be grouped into families, where it is considered that the results for one or more characteristics from any one product within the product family are representative for that same char

42、acteristics for all products within that same family BS EN 12566-4:2016EN 12566-4:2016 (E) 8 NOTE 2 Products may be grouped in different families for different characteristics. Reference to the assessment method standards should be made to allow the selection of a suitable representative sample. In

43、addition, the determination of the product type shall be performed for all characteristics included in the standard for which the manufacturer declares the performance: at the beginning of the production of a new or modified septic tank (unless a member of the same product family); or at the beginni

44、ng of a new or modified method of production (where this may affect the declared properties); or they shall be repeated for the appropriate characteristic(s), whenever a change occurs in the septic tank design, in the raw material or in the supplier of the components, or in the method of production

45、(subject to the definition of a product family), which would affect significantly one or more of the characteristics. Where components are used whose characteristics have already been determined, by the component manufacturer, on the basis of assessment methods of other product standards, these char

46、acteristics need not be re-assessed. The specifications of these components shall be documented. Products bearing regulatory marking in accordance with appropriate harmonized European specifications may be presumed to have the performances declared in the DoP, although this does not replace the resp

47、onsibility on the septic tank manufacturer to ensure that the septic tank as a whole is correctly manufactured and its component products have the declared performance values. 6.2.2 Test samples, testing and compliance criteria The number of samples of septic tank to be tested/assessed shall be in a

48、ccordance with Table 1. BS EN 12566-4:2016EN 12566-4:2016 (E) 9 Table 1 Number of samples to be tested and compliance criteria Characteristic Requirement Assessment method Number of tests/ samples Compliance criteria Inlets, outlets, internal pipework and connections See EN 125661:2016, 4.1.1 Accord

49、ing to EN 125661:2016, 4.1.1 Each unit in the product family Characteristic dimensions Overall dimensions See EN 125661:2016, 4.1.2 and 4.1.3 According to EN 125661:2016, 4.1.2 and 4.1.3 Each unit in the product family Characteristic overall dimensions Structural behaviour See EN 125661:2016, 4.2 According to EN 125661 One unit of the product family backfill load; hydrostatic loads; dynamic loads. Watertightness See EN 125661:2016, 4.3 According to EN 125661:2016, Annex A Each unit in the product family “Pass” or “F