DLA SMD-5962-97587 REV A-2007 MICROCIRCUIT DIGITAL BIPOLAR 4-BIT BINARY FULL ADDER WITH FAST CARRY MONOLITHIC SILICON《微型电路 数字型 双极 具有快速进位的 4 位二进制全加器 单块硅》.pdf

《DLA SMD-5962-97587 REV A-2007 MICROCIRCUIT DIGITAL BIPOLAR 4-BIT BINARY FULL ADDER WITH FAST CARRY MONOLITHIC SILICON《微型电路 数字型 双极 具有快速进位的 4 位二进制全加器 单块硅》.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-97587 REV A-2007 MICROCIRCUIT DIGITAL BIPOLAR 4-BIT BINARY FULL ADDER WITH FAST CARRY MONOLITHIC SILICON《微型电路 数字型 双极 具有快速进位的 4 位二进制全加器 单块硅》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing to current requirements. Editorial changes throughout. - gap 07-01-04 Joseph D. Rodenbeck REV SHET REV SHET REV STATUS REV A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Rajesh Pithadia

2、 DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Rajesh Pithadia COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Raymond Monnin MICROCIRCUIT, DIGITAL, BIPOLAR, 4-BIT BINARY FULL ADDER WITH FAST CARRY, AND AGENC

3、IES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 97-05-08 MONOLITHIC SILICON AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-97587 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E624-06 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD M

4、ICROCIRCUIT DRAWING SIZE A 5962-97587 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (d

5、evice class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 97587 01

6、Q E X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels an

7、d are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit functio

8、n as follows: Device type Generic number Circuit function 01 54F283 4-bit binary full adders with fast carry 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-

9、certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline l

10、etter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line F GDFP2-F16 or CDFP3-F16 16 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A

11、for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97587 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings.

12、1/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc Input voltage range (VIN) 2/ . -1.2 V dc to +7.0 V dc Input current range -30 mA to +5 mA Voltage range applied to any output in the high state -0.5 V to VCCCurrent into any output in the low state . 40 mA Storage temperature range -65C to 150C Po

13、wer dissipation . 303 mW Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) 175C 1.4 Recommended operating conditions. Supply voltage range (VCC) 4.5 V dc to 5.5 V dc High-level input voltage (VIH) . 2 V min Low-level input voltage (VIL) 0.8 V max Input clamp curr

14、ent (IIK) . -18 mA max High-level output current (IOH) -1 mA max Low-level output current (IOL) . 20 mA max Case operating temperature range (TC) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form

15、 a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE

16、STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are avail

17、able online at http:/assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited h

18、erein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum l

19、evels may degrade performance and affect reliability. 2/ The input voltage ratings may be exceeded provided the input current ratings are observed. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97587 DEFENS

20、E SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufact

21、urers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.

22、2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance wi

23、th 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.3 Electrical performance characteristics and post

24、irradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requireme

25、nts shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is

26、not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall

27、 be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certifica

28、te of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order t

29、o be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-

30、PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lo

31、t of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review

32、for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment

33、 for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 12 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97587 DEFENSE SUPP

34、LY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TC +125C Group A subgroupsLimits 2/ Unit unless otherwise specified Min Max Input clamp voltage VIKVCC= 4.5 V, II= -18 mA 1, 2,

35、3 -1.2 V High-level output voltage VOHVCC= 4.5 V, IOH= -1 mA 1, 2, 3 2.5 V Low-level output voltage VOLVCC= 4.5 V, IOL= 20 mA 1, 2, 3 0.5 V Input current IIVCC= 5.5 V, VI= 7 V 1, 2, 3 0.1 mA High-level input current IIHVCC= 5.5 V, VI= 2.7 V 1, 2, 3 20 A Low-level input Any A or B IILVCC= 5. 5 V, VI=

36、 0.5 V 1, 2, 3 -1.2 mA current C0 -0.6 Short-circuit output current IOS3/ VCC= 5.5 V, VO= 0 V 1, 2, 3 -60 -150 mA Supply current ICCVCC= 5.5 V, VI= 4.5 V 1, 2, 3 55 mA Functional test 4/ VIN= VIHMin or VILMax Verify output VO, See 4.4.1b 7, 8 Propagation delay time tPLHVCC= 5 V, See figure 4 9 2.7 9

37、.5 ns from C0 to VCC= 4.5 V to 5.5 V See figure 4 10, 11 2.7 14 tPHLVCC= 5 V, See figure 4 9 3.2 9.5 VCC= 4.5 V to 5.5 V See figure 4 10, 11 3.2 14 Propagation delay time tPLHVCC= 5 V, See figure 4 9 3.2 9.5 ns from A or B to VCC= 4.5 V to 5.5 V See figure 4 10, 11 3.2 14 tPHLVCC= 5 V, See figure 4

38、9 2.7 9.5 VCC= 4.5 V to 5.5 V See figure 4 10, 11 2.7 14 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97587 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION

39、LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C Group A subgroups Limits 2/ Unit unless otherwise specified Min Max Propagation delay time tPLHVCC= 5 V, See figure 4 9 2.7 7.5 ns from C0 to C4 VCC= 4.5 V to 5.

40、5 V See figure 4 10, 11 2.7 10.5 tPHLVCC= 5 V, See figure 4 9 2.2 7 VCC= 4.5 V to 5.5 V See figure 4 10, 11 2.2 10 Propagation delay time tPLHVCC= 5 V, See figure 4 9 2.7 7.5 ns from A or B to C4 VCC= 4.5 V to 5.5 V See figure 4 10, 11 2.7 10.5 tPHLVCC= 5 V, See figure 4 9 2.2 7 VCC= 4.5 V to 5.5 V

41、See figure 4 10, 11 2.2 10 1/ Each input/output, as applicable, shall be tested at the specified temperature, for the specified limits, to the tests in table I herein. Output terminals not designated shall be high level logic, low level logic, or open except for all ICCtests, where the output termin

42、als shall be open. When performing these tests, the current meter shall be placed in the circuit such that all current flows through the meter. 2/ For negative and positive voltage and current values, the sign designates the potential difference in reference to GND and the direction of current flow,

43、 respectively, and the absolute value of the magnitude, not the sign, is relative to the minimum and maximum limits, as applicable, listed herein. 3/ Not more than one output should be shorted at a time, and the duration of the short circuit should not exceed one second. 4/ Tests shall be performed

44、in sequence, attributes data only. Functional tests shall include the truth table and other logic patterns used for fault detection. The test vectors used to verify the truth table shall, at a minimum, test all functions of each input and output. All possible input to output logic patterns per funct

45、ion shall be guaranteed, if not tested, to the truth table in figure 2 herein. Functional tests shall be performed in sequence as approved by the qualifying activity on qualified devices. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICRO

46、CIRCUIT DRAWING SIZE A 5962-97587 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 Device type 01 Case outline E and F 2 Terminal number Terminal symbol 1 2 NC 2 B2 2 3 A2 B2 4 1 A2 5 A1 1 6 B1 NC 7 C0 A1 8 GND B1 9 C4 C0 10 4 GND 11 B4 NC 12 A4

47、 C4 13 3 4 14 A3 B4 15 B3 A4 16 VCCNC 17 3 18 A3 19 B3 20 VCCFIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97587 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVI

48、SION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 INPUTS OUTPUTS WHEN C0 = L WHEN C0 = H WHEN C2 = L WHEN C2 = H A1 B1 A2 B2 1 2 C2 1 2 C2 A3 B3 A4 B4 3 4 C4 3 4 C4 L L L L L L L H L L H L L L H L L L H L L H L L H L L L H L H H L L L H L H H L L L H L L H L H H L H L H L H H L L L H L H H L H H L L L H H H H L L L H H L H L L L H L H L H H L H L L H H H L L L H L H L H H H L L L H H H L H L L H H L H L L H H L L H H L H H L H H H L H L H H L H H H H L H L H H H H H H L H H H H H NOTE: Input conditions at A1, B1, A2, B2, and C0 are used