DLA MS25223 REV H-2005 GUARD SWITCH 3 POSITION《3号定位开关防护装置》.pdf

《DLA MS25223 REV H-2005 GUARD SWITCH 3 POSITION《3号定位开关防护装置》.pdf》由会员分享，可在线阅读，更多相关《DLA MS25223 REV H-2005 GUARD SWITCH 3 POSITION《3号定位开关防护装置》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 5930 MS25223H 30 August 2005 SUPERSEDING MS25223G 20 December 1982 DETAIL SPECIFICATION SHEET Guard, Switch, 3 Position This specification is approved for use by all Departments and Agencies of the Department of Defense. The complete requirements for acquiring the switch described here

2、in shall consist of this specification and the latest issue of MIL-DTL-7703. FIGURE 1 Dimensions and configuration. -1 Suitable for use with switches having toggle levers in accordance with detail A. FIGURE 1 Dimensions and configuration INCH-POUNDINACTIVE FOR NEW DESIGN AFTER 30 AUGUST 2005 Provide

3、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25223H 2-2 Suitable for use with switches having toggle lever in accordance with detail B. FIGURE.1: Dimensions and configuration Continued Inches mm Inches mm Inches mm .003 .08 .188 4.77 .750 19.05 .005 .1

4、3 .240 6.10 .825 20.95 .008 .20 .248 6.30 .840 21.34 .016 .41 .276 7.01 .875 22.22 .031 .79 .312 7.92 .906 23.01 .032 .81 .360 9.14 .946 24.03 .050 1.27 .469 11.91 1.062 26.97 .062 1.57 .475 12.06 1.312 33.32 .075 1.90 .516 13.11 1.437 36.50 .081 2.06 .575 14.60 1.575 40.00 .096 2.44 .594 15.09 1.63

5、5 41.53 .156 3.96 .688 17.47 1.812 46.02 .187 4.75 .719 18.26 2.125 53.98 DASH NO. TYPE PANEL THICKNESS (REF) OPERATING FORCE -1 3- HOLE MOUNTING .050 TO .081 -2 1- HOLE MOUNTING .050 TO .248 .1 TO .7 LB Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-

6、,-MS25223H 3NOTES: 1. Dimensions are in inches. 2. Unless otherwise specifies, Tolerances are .016 on decimals. 3. For design feature purposed, this standard takes precedence over procurement documents referenced herein. 4. Referenced documents shall be of the issue in effect on date of invitations

7、for bid. 5. Finish: Zinc plate, ASTM B 633, type III, or cadmium plate, SAE-AMS-QQ-P-416, type III, with optional supplementary treatment per MIL-C-8514 or DOD-P-15328, black enamel, lusterless, color number 37038 or semi-gloss, color number 27038, FED-STD-595 or equivalent. 6. Material: Plastic, mo

8、lded, red color shade 11136, FED-STD- 595. Steel, commercial, shall be smooth and free from burrs. REQUIREMENTS Opening the guard shall not move the switch contacts. Closing the guard shall place the switch lever in the center position from closing the guard shall place the switch lever in the cente

9、r position from either the up or down position. Referenced documents MIL-DTL-7703 MIL-C-8514 ASTMB 633 SAE-AMS-QQ-P-416 DOD-P-15328 FED-STD-595 Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Prepar

10、ing activity Army CR DLA -CC Navy AS (Project 5930-2005-008) Air Force 11 DLA CC Review activities: Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-