DLA MIL-S-43828 A (1)-1985 STRAP WEBBING CARGO TIE DOWN LIGHTWEIGHT PACK FRAME M-1972《M-1972用绳捆扎织物带系住装运货物》.pdf

《DLA MIL-S-43828 A (1)-1985 STRAP WEBBING CARGO TIE DOWN LIGHTWEIGHT PACK FRAME M-1972《M-1972用绳捆扎织物带系住装运货物》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-S-43828 A (1)-1985 STRAP WEBBING CARGO TIE DOWN LIGHTWEIGHT PACK FRAME M-1972《M-1972用绳捆扎织物带系住装运货物》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-S-43828A AMENDMENT- 1, il February 1985 MILITARY SPECIFICATION STRAP, WEBBING, CARGO TIE DOWN, LIGHTWEIGHTPACK FRAME, M-1972 This amendment forms a part of Military Specification MIL-S-43828A dated 7 January 1983 and is approved for use by all Departments and Agencies of the Department of Defens

2、e. PAGE 1 2.1 , under “SPECIFICATION FEDERAL“ ADD: “TT-E-529 - Enamel Alkyd semigloss“ under tlSPECIFICATION MILITARY“ Delete: “MIL-E-480 - Enamel Baking, Phenol - or Urea Formaldehyde“ PAGE 2 2.1, under “STANDARDS MILITARY“: Delete “MIL-STD-1188 - Commercial Packaging of Supplies and Equipment“. 2.

3、2, after line 5: Add “D 3951 - Standard Practice for Commercial Packaging“. PAGE 3 3.3.3, line 3: After “Part No. 3837,“: Add “Brookside Part No, SP920“. 3.3.3.1: Delete “Type I or II of MIL-E-480“ and substitute “Type II of TT-E-529 I, Add new paragraph: “3.3.3.2 Epoxy coating. As an alternate to t

4、he zinc plate and enamel specified in 3.3.3.1. epoxy coating. accordance with the manufacturers instructions, The coating on all components shall be performed prior to assembly and shall level out to a smooth and uniform film without orange peel, wrinkles, drops, streaks or areas of no film (see 4.4

5、.1.1),“ The fasteners may be coated with general motors 4350-M The color shall be black. The coating shall be applied in . 3.3.4, line 3: Delete “Part No. 3837“ and substitute “Part No. 3838, Brookside Part No. SP950“. 3.3.4.1, after “3.3.3.1: Add “or 3.3.3.2“. FSC 8465 Page 1 of 2 y- Provided by IH

6、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-43828A Amendment-1 PAGE 7 4.4.3, line 4: Delete “with the exception that it need not be closed“. Delete the fourth sentence. PAGE 8 5.1.2: Delete: “MIL-STD-1188“ and substitute !ASTM D 3951“. 5.2.1, line 3, aft

7、er iiPPP-B-636,“ Add “The inside dimensions shall approximate 15-1/4 inches in length, 9 inches in width and 15-1/4 inches in depth. Approximate dimensions are furnished as a guide only.“ PAGE 9 5.2.2, line 3, after “PPP-B-636,“ Add “The inside dimensions shall approximate 15-1/4 inches in length, 9

8、 inches in width and 15-1/4 inches in depth. 5.2.3, line 2: Delete “MIL-STD-1188“ and Substitute “ASTM D 3951“. 5.3: Delete and substitute: “5.3 Palletization. When specified (see 6.2), straps, packed as specified in 5.2, shall be palletized on a 4-way entry pallet in accordance with load type Ia of

9、 MIL-STD-147. secondary straps in accordance with bonding means K and L or film bonding means O or P, appendix of MIL-STD-147. Interlocking of loads shall be effected by reversing the pattern of each course.“ Each prepared load shall be bonded with primary and Pallet patterns shall be pattern number

10、 15 as specified in the 5.4, line 3, after “MIL-STD-129“: Add “or ASTM D 3951 as applicable“. Custodians: Arhy - GL Navy - Nu Review activities: Army - MD Navy - MC DLA - CT User activity: Navy - YD Preparing activity: Army - GL Project No. 8465-0898 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-