DLA MIL-PRF-39006 25 E-2012 CAPACITORS FIXED ELECTROLYTIC (NONSOLID ELECTROLYTE) TANTALUM (POLARIZED SINTERED SLUG) (EXTENDED RANGE) 85癈 (VOLTAGE DERATED TO 125癈) ESTABLISHED RELI.pdf
《DLA MIL-PRF-39006 25 E-2012 CAPACITORS FIXED ELECTROLYTIC (NONSOLID ELECTROLYTE) TANTALUM (POLARIZED SINTERED SLUG) (EXTENDED RANGE) 85癈 (VOLTAGE DERATED TO 125癈) ESTABLISHED RELI.pdf》由会员分享,可在线阅读,更多相关《DLA MIL-PRF-39006 25 E-2012 CAPACITORS FIXED ELECTROLYTIC (NONSOLID ELECTROLYTE) TANTALUM (POLARIZED SINTERED SLUG) (EXTENDED RANGE) 85癈 (VOLTAGE DERATED TO 125癈) ESTABLISHED RELI.pdf(11页珍藏版)》请在麦多课文档分享上搜索。
1、 INCH-POUND MIL-PRF-39006/25E 7 December 2012 SUPERSEDING MIL-PRF-39006/25D 24 October 2006 PERFORMANCE SPECIFICATION SHEET CAPACITORS, FIXED, ELECTROLYTIC (NONSOLID ELECTROLYTE), TANTALUM, (POLARIZED, SINTERED SLUG), (EXTENDED RANGE) 85C (VOLTAGE DERATED TO 125C), ESTABLISHED RELIABILITY, STYLE CLR
2、81 This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-39006. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in pare
3、ntheses. 3. Metric equivalents are given for general information only. 4. The weld shall not be enclosed in the end seal. 5. CLR81 capacitors are replacements for the inactive CLR69s (MIL-PRF-39006/21), silver cased wet slug capacitors. 6. CLR81 capacitors have higher capacitance values than CLR79s
4、(MIL-PRF-39006/22) of the same case size and voltage rating. 7. Low ESR versions of CLR81s may be found in MIL-PRF-39006/31 (CLR91). FIGURE 1. Style CLR81 capacitors. AMSC N/A FSC 5910 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39006/25E
5、 2 Case size Dimensions Basic case Insulated case E .250 (6.35) L 1/ +.031 (0.79) -.016 (0.41) D .016 (0.41) D max T1 .453 (11.51) .188 (4.78) .219 ( 5.56) 1.500 (38.10) T2 .641 (16.28) .281 (7.14) .312 ( 7.92) 2.250 (57.15) T3 .766 (19.46) .375 (9.52) .406 (10.31) 2.250 (57.15) T4 1.062 (26.97) .37
6、5 (9.52) .406 (10.31) 2.250 (57.15) 1/ Length of basic case sleeving shall be as specified in MIL-PRF-39006. FIGURE 1. Style CLR81 capacitors - Continued. REQUIREMENTS: Design and construction: Dimensions and configuration: See figure 1. Case type: Tantalum, tubular, insulated. Seal type: Hermetic (
7、glass-to-tantalum anode). Terminals: Axial-wire lead: Cathode and anode (type N32, N51, or N52 of MIL-STD-1276). Rated temperature: -55C to +85C, voltage derated to +125C (see figure 2). FIGURE 2. Voltage derating with temperature. Provided by IHSNot for ResaleNo reproduction or networking permitted
8、 without license from IHS-,-,-MIL-PRF-39006/25E 3 Rated voltage: See table I. Capacitance (Cap.) nominal (nom): See table I. Cap. tolerance: 10 percent or 20 percent (see table I). FR level: M, P, R, and S (see table I). DC leakage (DCL) (max) (at +25C): See table I. Cap. (nominal): Method 305 of MI
9、L-STD-202. Dissipation factor (DF) (max): See table I. Seal: Method 112 of MIL-STD-202, conditions A or D, and C. Shock (specified pulse): Method 213 of MIL-STD-202, condition I (100 gs) or condition D (500 gs), as applicable. Vibration, high frequency: Method 204 of MIL-STD-202, condition D (20 gs)
10、 or condition H (80 gs), as applicable. Random vibration (as applicable): Method 214 of MIL-STD-202, test condition II-K (51 gs). Thermal shock: Method 107 of MIL-STD-202, condition A (with step 3 at +125C). Number of cycles: In accordance with MIL-PRF-39006, the following shall apply. DCL: 200 perc
11、ent (max) of +25C value of table I for qualification and group C. DCL: 125 percent (max) of +25C value of table I for group B. Cap: Within 5 percent of initial measurement. DF: 115 percent (max) of initial requirement. Salt atmosphere (corrosion): Method 101 of MIL-STD-202, condition B (48 hours). S
12、olderability: Method 208 of MIL-STD-202. Terminal strength: Pull: Method 211 of MIL-STD-202, condition A. Wire-lead bend: In accordance with MIL-PRF-39006. Surge voltage: See table I. Moisture resistance: Method 106 of MIL-STD-202. DCL: 125 percent (max) of +25C value of table I. Cap: Within 8 perce
13、nt of initial measurement. DF: 115 percent (maximum) of initial requirement. Dielectric withstanding voltage (DWV): Method 301 of MIL-STD-202. 2,000 V dc, minimum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Capacitor characteristics. Ra
14、ted voltage (+85C) 1/ Cap. Cap. toler-ance DC leakage (max) Dissi-pation factor (max) ESR at +25C (max) 2/ Derated voltage (+125C) 1/ Surge voltage (+85C) Imped- ance (max) Capacitance change at Max 85C 40 kHz ripple current 3/ Case size PIN M39006/25- 4/ Failure rate level (%/1,000 hour) +25C +85C,
15、 +125C -55C +85C +125C M(1.0) P(0.1) R(0.01) S(0.001) V dc F percent A A percent Ohms V dc V dc Ohms percent percent percent mA rms 6 220 20 2 9 50 3.02 4 6.9 36 -64 +13 +16 1,000 T1 0001- 0089- 0177- 0265- 6 220 10 2 9 50 3.02 4 6.9 36 -64 +13 +16 1,000 T1 0002- 0090- 0178- 0266- 6 820 20 3 14 155
16、2.51 4 6.9 18 -88 +16 +20 1,500 T2 0003- 0091- 0179- 0267- 6 820 10 3 14 155 2.51 4 6.9 18 -88 +16 +20 1,500 T2 0004- 0092- 0180- 0268- 6 1,500 20 5 20 172 1.52 4 6.9 18 -90 +20 +25 1,900 T3 0005- 0093- 0181- 0269- 6 1,500 10 5 20 172 1.52 4 6.9 18 -90 +20 +25 1,900 T3 0006- 0094- 0182- 0270- 6 2,20
17、0 20 6 24 170 1.03 4 6.9 13 -90 +25 +30 2,300 T4 0007- 0095- 0183- 0271- 6 2,200 10 6 24 170 1.03 4 6.9 13 -90 +25 +30 2,300 T4 0008- 0096- 0184- 0272- 8 180 20 2 9 41 3.02 5 9.2 45 -60 +13 +16 1,000 T1 0009- 0097- 0185- 0273- 8 180 10 2 9 41 3.02 5 9.2 45 -60 +13 +16 1,000 T1 0010- 0098- 0186- 0274
18、- 8 680 20 3 14 130 2.54 5 9.2 22 -83 +16 +20 1,500 T2 0011- 0099- 0187- 0275- 8 680 10 3 14 130 2.54 5 9.2 22 -83 +16 +20 1,500 T2 0012- 0100- 0188- 0276- 8 1,500 20 5 20 170 1.50 5 9.2 18 -90 +20 +25 1,900 T3 0013- 0101- 0189- 0277- 8 1,500 10 5 20 170 1.50 5 9.2 18 -90 +20 +25 1,900 T3 0014- 0102
19、- 0190- 0278- 8 1,800 20 7 25 138 1.02 5 9.2 14 -90 +25 +30 2,300 T4 0015- 0103- 0191- 0279- 8 1,800 10 7 25 138 1.02 5 9.2 14 -90 +25 +30 2,300 T4 0016- 0104- 0192- 0280- 10 150 20 2 9 34 3.01 7 11.5 54 -55 +13 +16 900 T1 0017- 0105- 0193- 0281- 10 150 10 2 9 34 3.01 7 11.5 54 -55 +13 +16 900 T1 00
20、18- 0106- 0194- 0282- 10 560 20 3 16 106 2.51 7 11.5 27 -77 +16 +20 1,450 T2 0019- 0107- 0195- -0283- 10 560 10 3 16 106 2.51 7 11.5 27 -77 +16 +20 1,450 T2 0020- 0108- 0196- 0284- 10 1,200 20 5 20 137 1.51 7 11.5 18 -88 +20 +25 1,850 T3 0021- 0109- 0197- 0285- 10 1,200 10 5 20 137 1.51 7 11.5 18 -8
21、8 +20 +25 1,850 T3 0022- 0110- 0198- 0286- 10 1,500 20 7 25 114 1.01 7 11.5 15 -88 +25 +30 2,300 T4 0023- 0111- 0199- 0287- 10 1,500 10 7 25 114 1.01 7 11.5 15 -88 +25 +30 2,300 T4 0024- 0112- 0200- 0288- 15 100 20 2 9 30 3.98 10 17.2 72 -44 +13 +16 900 T1 0025- 0113- 0201- 0289- 15 100 10 2 9 30 3.
22、98 10 17.2 72 -44 +13 +16 900 T1 0026- 0114- 0202- 0290- 15 390 20 3 16 74 2.52 10 17.2 31 -66 +16 +20 1,450 T2 0027- 0115- 0203- 0291- 15 390 10 3 16 74 2.52 10 17.2 31 -66 +16 +20 1,450 T2 0028- 0116- 0204- 0292- 15 820 20 6 24 111 1.80 10 17.2 22 -77 +20 +25 1,800 T3 0029- 0117- 0205- 0293- 15 82
23、0 10 6 24 111 1.80 10 17.2 22 -77 +20 +25 1,800 T3 0030- 0118- 0206- 0294- 15 1,000 20 8 32 92 1.22 10 17.2 17 -77 +25 +30 2,300 T4 0031- 0119- 0207- 0295- 15 1,000 10 8 32 92 1.22 10 17.2 17 -77 +25 +30 2,300 T4 0032- 0120- 0208- 0296- 25 68 20 2 9 22 4.29 15 28.8 90 -40 +12 +15 850 T1 0033- 0121-
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMILPRF3900625E2012CAPACITORSFIXEDELECTROLYTICNONSOLIDELECTROLYTETANTALUMPOLARIZEDSINTEREDSLUGEXTENDEDRANGE85

链接地址:http://www.mydoc123.com/p-692855.html