DLA MIL-PRF-22885 105 C-2010 SWITCH PUSHBUTTON ILLUMINATED PLUG-IN SWITCH MODULE FOR 2PDT 4PDT.pdf

《DLA MIL-PRF-22885 105 C-2010 SWITCH PUSHBUTTON ILLUMINATED PLUG-IN SWITCH MODULE FOR 2PDT 4PDT.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-22885 105 C-2010 SWITCH PUSHBUTTON ILLUMINATED PLUG-IN SWITCH MODULE FOR 2PDT 4PDT.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5930 INCH-POUND MIL-PRF-22885/105C 4 June 2010 SUPERSEDING MIL-PRF-22885/105B 2 April 2004 PERFORMANCE SPECIFICATION SHEET SWITCH, PUSHBUTTON, ILLUMINATED, PLUG-IN, SWITCH MODULE FOR, 2PDT, 4PDT This specification is approved for use by all Departments and Agencies of the Department of

2、Defense. The requirements for acquiring the switches described herein shall consist of this specification sheet and MIL-PRF-22885. FIGURE 1. Dimensions and configurations. INSTALLATION JACKSCREW LATCH LEVER PUSHBUTTON RELEASE POSITIVE INDEX POST FOR PUSHBUTTON COMBINATION TERMINAL SOLDER OR SPADE LU

3、G STYLE S STYLE C STYLE I .25 (6.4) 1.44 (36.6) 2.25 (57.2) 2.23 (36.6) .20 (5.1) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/105C 2 FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction o

4、r networking permitted without license from IHS-,-,-MIL-PRF-22885/105C 3 NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .015 (.38 mm) for three place decimals and .03 (.8 mm) for two place decimals. 3. Inde

5、x post provided prevents incorrect insertion of pushbutton into switch housing. 4. The installation torque for switch mounting jackscrew to be 8 ounce-inches maximum 5. Delete Terminals 8 thru 13 for 2PDT configuration. 6. Delete Terminals 5 thru 16 for indicator configuration. 7. Delete Terminal B

6、for common lamp ground lamp circuit. 8. On momentary operation switches, Terminals 6, 9, 12 and 15 are normally closed. 9. Unit is built with only the required terminals. 10. Metric equivalents are in parentheses. FIGURE 1. Dimensions and configuration - Continued. Provided by IHSNot for ResaleNo re

7、production or networking permitted without license from IHS-,-,-MIL-PRF-22885/105C 4 REQUIREMENTS: Design and construction: See figure 1. Intended use: Mates with sunlight readable pushbutton in accordance with MIL-PRF-22885/104. Styles S and C mate with individual or multistation switch housings in

8、 accordance with MIL-PRF-22885/103 and MIL-S-24317/12. Style I modules mount in MIL-S-24317/12 multistation housings only. Styles S and C are designed to be replaced from front of panel without disconnecting behind the panel wiring. Style I requires access to behind the panel mounting screw and remo

9、val of wiring. Style C terminals mate with M39029/1-101 connector contacts. Classification: Enclosure design: 1 (Unsealed). Temperature characteristic: 1(-55C to +85C). Vibration grade: 3(10 - 2,000 Hz, 15 g peak). Operation: A (Momentary action). B (Alternate action). H (Indicator only). Material:

10、Common termination system (applicable to style C): Weight (10%): Style I: .0176 pound. Styles C and S: .032 pound. Operating characteristics: In accordance with MIL-PRF-22885/103 and MIL-S-24317/12. Electrical endurance: 25,000 cycles. See table I for test loads. TABLE I. Electrical ratings. Load Se

11、a level and 70,000 ft. 28 V dc 115 V ac Resistive Inductive Lamp 2 Amperes 1 Ampere .75 Ampere 2 Amperes 1 Ampere .75 Ampere Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-22885/105C 5 Dielectric withstanding voltage: Sea level: 1,056 V rms.

12、 70,000 ft: 450 V rms. Logic level life: Applicable. Terminal identification: Circuit schematic shall be marked. Identification of terminals on style C modules not required. Part number: See table II. Qualification and periodic inspection: Required as a part of MIL-PRF-22885/103 or MIL-S-24317/12 sw

13、itch assemblies. TABLE III. Part numbers. Part number M22885/105- Style Termination 1/ Operation Switch circuit Lamp CKT 2/ 001 I Solder Indicator N/A CLG 002 I Solder Indicator N/A SLG 003 S Solder or wire wrap Indicator N/A CLG 004 S Solder or wire wrap Indicator N/A SLG 005 C Crimp pin Indicator

14、N/A CLG 006 C Crimp pin Indicator N/A SLG 007 S Solder or wire wrap Momentary 4PDT CLG 008 S Solder or wire wrap Momentary 4PDT SLG 009 S Solder or wire wrap Momentary 2PDT CLG 010 S Solder or wire wrap Momentary 2PDT SLG 011 S Solder or wire wrap Alternate 4PDT CLG 012 S Solder or wire wrap Alterna

15、te 4PDT SLG 013 S Solder or wire wrap Alternate 2PDT CLG 014 S Solder or wire wrap Alternate 2PDT SLG 015 C Crimp pin Momentary 4PDT CLG 016 C Crimp pin Momentary 4PDT SLG 017 C Crimp pin Momentary 2PDT CLG 018 C Crimp pin Momentary 2PDT SLG 019 C Crimp pin Alternate 4PDT CLG 020 C Crimp pin Alterna

16、te 4PDT SLG 021 C Crimp pin Alternate 2PDT CLG 022 C Crimp pin Alternate 2PDT SLG 1/ Style I modules mount in style I multistation housings in accordance with MIL-24317/12. Style S modules mate with styles S, W or L individual or multistation housings in accordance with MIL-PRF-22885/103 and MIL-S-2

17、4317/12. Style C modules mate with style C individual or multistation housings in accordance with MIL-PRF-22885/103 and MIL-S-24317/12. 2/ CLG = Common lamp ground. SLG = Split lamp ground. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-2288

18、5/105C 6 The margins of this specification are marked with vertical lines to indicate where modifications from this revision were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautione

19、d to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. Reference Documents: MIL-PRF-22885 MIL-PRF-22885/103 MIL-PRF-22885/104 MIL-S-24317/12 Custodian: Preparing activity: Navy - EC DLA - CC Air Force - 85 DLA-CC (Project 5930-2009-017) Re

20、view activities: Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/ . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-