DLA MIL-PRF-19500 751-2008 SEMICONDUCTOR DEVICE FIELD EFFECT TRANSISTOR P-CHANNEL SILICON TYPE 2N7508U3 JANTX JANTXV AND JANS.pdf

《DLA MIL-PRF-19500 751-2008 SEMICONDUCTOR DEVICE FIELD EFFECT TRANSISTOR P-CHANNEL SILICON TYPE 2N7508U3 JANTX JANTXV AND JANS.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-19500 751-2008 SEMICONDUCTOR DEVICE FIELD EFFECT TRANSISTOR P-CHANNEL SILICON TYPE 2N7508U3 JANTX JANTXV AND JANS.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-PRF-19500/751 27 October 2008 PERFORMANCE SPECIFICATION SHEET SEMICONDUCTOR DEVICE, FIELD EFFECT TRANSISTOR, P-CHANNEL, SILICON, TYPE 2N7508U3, JANTX, JANTXV, AND JANS This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acqui

2、ring the product described herein shall consist of this specification sheet and MIL-PRF-19500. 1. SCOPE 1.1 Scope. This specification covers the performance requirements for an P-channel, enhancement-mode, MOSFET, power transistor. Three levels of product assurance are provided for each device type

3、as specified in MIL-PRF-19500. 1.2 Physical dimensions. See figure 1, SMD-0.5, TO-276AA (U3). 1.3 Maximum ratings. (Unless otherwise specified, TA= +25C). Type PT(1) TC= +25C PTTA= +25C RJC(2) VDSVDGVGSID1(3) (4)TC= +25CID2TC= +100C ISIDM(5) TJand TSTG2N7508U3 W 75 W 1.56 C/W 1.67 V dc -150 V dc -15

4、0 V dc 20 A dc -11 A dc -7.2 A dc -11 A(pk) -44 C -55 to +150 (1) Derate linearly 0.6 W/C for TC +25C; (2) See figure 2, thermal impedance curves. (3) The following formula derives the maximum theoretical IDlimit. IDis also limited to 22 A by package, internal construction wires and package pin size

5、. (4) See figure 3, maximum drain current graph. (5) IDM= 4 X ID1as calculated in note (3). AMSC N/A FSC 5961 INCH-POUND Comments, suggestions, or questions on this document should be addressed to Defense Supply Center, Columbus, ATTN: DSCC-VAC, P.O. Box 3990, Columbus, OH 43218-3990, or emailed to

6、Semiconductordscc.dla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil/. Tat )on (Rx RT- T= IJMDSJCCJMDProvided by IHSNot for ResaleNo reproduction or networking permitted without

7、license from IHS-,-,-MIL-PRF-19500/751 2 1.4 Maximum ratings. Unless otherwise specified, TC= +25C. Type Min V(BR)DSS VGS= 0 VGS(TH)VDS VGSID = -0.25 Max IDSS1VGS= 0 VDS= 100 Max rDS(ON)(1) VGS= -10 V dc EAS at IASIAS ID= -0.25 mA dc mA dc percent of rated VDSTJ= +25C at ID2TJ= +150C at ID2V dc V dc

8、 A dc ohm ohm mJ A Min Max 2N7508U3 -150 -2.0 -4.0 -25 0.290 0.585 130 -7.2 (1) Pulsed (see 4.5.1). 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of

9、 this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether

10、 or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the soli

11、citation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-19500 - Semiconductor Devices, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-750 - Test Methods for Semiconductor Devices. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/

12、 or http:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references ci

13、ted herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19500/751 3 D

14、imensions Ltr. Inches Millimeters Min Max Min Max BL .395 .405 10.04 10.28 BW .291 .301 7.40 7.64 CH .1085 .123 2.76 3.12 LH .010 .020 0.25 0.51 LW1 .281 .291 7.14 7.39 LW2 .090 .100 2.29 2.54 LL1 .220 .230 5.59 5.84 LL2 .115 .125 2.93 3.17 LS1 .150 BSC 3.81 BSC LS2 .075 BSC 1.91 BSC Q1 .030 0.762 Q

15、2 .030 0.762 TERM 1 Drain TERM 2 Gate TERM 3 Source NOTES: 1. Dimensions are in inches. 2. Millimeters are given for general information only. 3. In accordance with ASME Y14.5M, diameters are equivalent to x symbology. 4. Terminal 1 - Drain, Terminal 2 - Gate, Terminal 3 - Source. FIGURE 1. Physical

16、 dimensions for SMD-0.5 TO-276AA (2N7508U3). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19500/751 4 3. REQUIREMENTS 3.1 General. The individual item requirements shall be as specified in MIL-PRF-19500 and as modified herein. 3.2 Qualific

17、ation. Devices furnished under this specification shall be products that are manufactured by a manufacturer authorized by the qualifying activity for listing on the applicable qualified manufacturers list (QML) before contract award (see 4.2 and 6.3). 3.3 Abbreviations, symbols, and definitions. Abb

18、reviations, symbols, and definitions used herein shall be as specified in MIL-PRF-19500 and as follows. IAS- Rated avalanche current, nonrepetitive. nC - nano coulomb. 3.4 Interface and physical dimensions. Interface and physical dimensions shall be as specified in MIL-PRF-19500, and on figures 1, S

19、MD-0.5 (TO-276AA) herein. 3.4.1 Lead finish. Lead finish shall be solderable in accordance with MIL-PRF-19500, MIL-STD-750, and herein. Where a choice of lead finish is desired, it shall be specified in the acquisition document (see 6.2). 3.5 Marking. Marking shall be in accordance with MIL-PRF-1950

20、0. 3.6 Electrostatic discharge protection. The devices covered by this specification require electrostatic discharge protection. 3.6.1 Handling. MOS devices must be handled with certain precautions to avoid damage due to the accumulation of static charge. However, the following handling practices ar

21、e recommended (see 3.6). a. Devices should be handled on benches with conductive and grounded surface. b. Ground test equipment, tools, and personnel handling devices. c. Do not handle devices by the leads. d. Store devices in conductive foam or carriers. e. Avoid use of plastic, rubber, or silk in

22、MOS areas. f. Maintain relative humidity above 50 percent, if practical. g. Care should be exercised, during test and troubleshooting, to apply not more than maximum rated voltage to any lead. h. Gate must be terminated to source. R 100 k, whenever bias voltage is to be applied drain to source. 3.7

23、Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in 1.3, 1.4, and table I. 3.8 Electrical test requirements. The electrical test requirements shall be as specified in table I. 3.9 Workmanship. Semiconductor devices

24、 shall be processed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19500/751 5 4. VERIFICATION 4.1 Classif

25、ication of inspections. The inspection requirements specified herein are classified as follows: a. Qualification inspection (see 4.2). b. Screening (see 4.3). c. Conformance inspection (see 4.4 and table I). 4.2 Qualification inspection. Qualification inspection shall be in accordance with MIL-PRF-1

26、9500. Alternate flow is allowed for qualification inspection in accordance with MIL-PRF-19500. 4.2.1 Group E qualification. Group E inspection shall be performed for qualification or re-qualification only. In case qualification was awarded to a prior revision of the specification sheet that did not

27、request the performance of table II tests, the tests specified in table II herein that were not performed in the prior revision shall be performed by the first inspection lot of this revision to maintain qualification. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

28、nse from IHS-,-,-MIL-PRF-19500/751 6 4.3 Screening (JANS, JANTX and JANTXV levels only). Screening shall be in accordance with table E-IV of MIL-PRF-19500 and as specified herein. The following measurements shall be made in accordance with table I herein. Devices that exceed the limits of table I he

29、rein shall not be acceptable. Screen (see table E-IV of Measurement MIL-PRF-19500) (1) (2) JANS level JANTX and JANTXV levels (3) Gate stress test (see 4.3.1) Gate stress test (see 4.3.1) (3) (4) Method 3470 of MIL-STD-750 (see 4.3.2) optional Method 3470 of MIL-STD-750 (see 4.3.2) optional (3) 3c M

30、ethod 3161 of MIL-STD-750 (see 4.3.3) Method 3161 of MIL-STD-750 (see 4.3.3) 9 IGSSF1, IGSSR1, IDSS1, subgroup 2 of table I herein Not applicable 10 Method 1042 of MIL-STD-750, test condition B Method 1042 of MIL-STD-750, test condition B 11 Subgroup 2 of table I herein; IGSSF1, IGSSR1, IDSS1, rDS(o

31、n)1,VGS(TH)1, IGSSF1= 20 nA dc or 100 percent of initial value, whichever is greater. IGSSR1= 20 nA dc or 100 percent of initial value, whichever is greater. IDSS1= 25 A dc or 100 percent of initial value, whichever is greater. Subgroup 2 of table I herein, IGSSF1, IGSSR1, IDSS1, rDS(on)1,VGS(TH)112

32、 Method 1042 of MIL-STD-750, test condition A Method 1042 of MIL-STD-750, test condition A 13 Subgroups 2 and 3 of table I herein. IGSSF1= 20 nA dc or 100 percent of initial value, whichever is greater. IGSSR1= 20 nA dc or 100 percent of initial value, whichever is greater. IDSS1= 25 A dc or 100 per

33、cent of initial value, whichever is greater. rDS(on)1= 20 percent of initial value. VGS(TH)1= 20 percent of initial value. Subgroup 2 of table I herein. IGSSF1= 20 nA dc or 100 percent of initial value, whichever is greater. IGSSR1= 20 nA dc or 100 percent of initial value, whichever is greater. IDS

34、S1= 25 A dc or 100 percent of initial value, whichever is greater. rDS(on)1= 20 percent of initial value. VGS(TH)1 = 20 percent of initial value. (1) At the end of the test program, IGSSF1IGSSR1, and IDSS1are measured. (2) An out-of-family program to characterize IGSSF1, IGSSR1, IDSS1, and VGS(th)1s

35、hall be invoked. (3) Shall be performed anytime after temperature cycling, screen 3a; and does not need to be repeated in screening requirements. (4) Method 3470 is optional if performed as a sample in group A, subgroup 5. Provided by IHSNot for ResaleNo reproduction or networking permitted without

36、license from IHS-,-,-MIL-PRF-19500/751 7 4.3.1 Gate stress test. Apply VGS= 24 V minimum for t = 250 s minimum. 4.3.2 Single pulsed unclamped inductive switching. a. Peak current, ID.IAS(max). b. Peak gate voltage, VGS-10 V, up to maximum rated VGS c. Gate to source resistor, RGS.25 Rg 200. d. Initi

37、al case temperature .+25C, +10C, -5C. e. Inductance, L . .minimum mH V)V- V()I(2EBRDDBR2D1AS f. Number of pulses to be applied .1 pulse. g. Supply voltage (VDD) -50 V. 4.3.3 Thermal impedance. The thermal impedance measurements shall be performed in accordance with method 3161 of MIL-STD-750 using t

38、he guidelines in that method for determining IM, IH, tH, tSW, (and VHwhere appropriate). Measurement delay time (tMD) = 70 s max. See table II, group E, subgroup 4 herein. 4.4 Conformance inspection. Conformance inspection shall be in accordance with MIL-PRF-19500. Alternate flow is allowed for conf

39、ormance inspection in accordance with MIL-PRF-19500. 4.4.1 Group A inspection. Group A inspection shall be conducted in accordance with MIL-PRF-19500 and table I herein. Electrical measurements (end-points) shall be in accordance with the inspections of table I, subgroup 2 herein. 4.4.2 Group B insp

40、ection. Group B inspection shall be conducted in accordance with the conditions specified for subgroup testing in table E-VIA (JANS) and table E-VIB (JANTX and JANTXV) of MIL-PRF-19500 and as follows. Electrical measurements (end-points) shall be in accordance with the inspections of table I, subgro

41、up 2 herein. 4.4.2.1 Group B inspection table E-VIA (JANS) of MIL-PRF-19500. Subgroup Method Conditions B3 1051 Test condition G. B4 1042 Test condition D, 2,000 cycles. The heating cycle shall be 1 minute minimum. No heat sink nor forced air cooling on the device shall be permitted during the “on“

42、cycle. B5 1042 A separate sample may be pulled for each test. Accelerated steady-state reverse bias; test condition A, VDS= rated, TA= +175C, t = 120 hours, read and record VBR(DSS)(pre and post) at ID= -1 mA. Read and record IDSS(pre and post). B5 1042 Accelerated steady-state gate stress; test con

43、dition B, VGS= rated, TA= +175C, t = 24 hours. B5 2037 Test condition D. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19500/751 8 4.4.2.2 Group B inspection table E-VIB (JANTX and JANTXV) of MIL-PRF-19500. Subgroup Method Conditions B2 105

44、1 Test condition G. B3 1042 Test condition D, 2,000 cycles. The heating cycle shall be 1 minute minimum. No heat sink nor forced air cooling on the device shall be permitted during the “on“ cycle. 4.4.3 Group C inspection. Group C inspection shall be conducted in accordance with the conditions speci

45、fied for subgroup testing in table E-VII of MIL-PRF-19500 and as follows. Electrical measurements (end-points) shall be in accordance with the inspections of table I, subgroup 2 herein. 4.4.3.1 Group C inspection (table E-VII of MIL-PRF-19500). Subgroup Method Conditions C2 2036 Not applicable. C5 3

46、161 RJC= 1.67 C/W maximum. See 4.5.2. C6 1042 Test condition D, 6,000 cycles. The heating cycle shall be 1 minute minimum. No heat sink nor forced air cooling on the device shall be permitted during the “on“ cycle. 4.4.4 Group E inspection. Group E inspection shall be conducted in accordance with th

47、e conditions specified for subgroup testing in table E-IX of MIL-PRF-19500 and as specified in table II herein. Electrical measurements (end-points) shall be in accordance with table I, subgroup 2 herein. 4.5 Methods of inspection. Methods of inspection shall be as specified in the appropriate table

48、s and as follows. 4.5.1 Pulse measurements. Conditions for pulse measurement shall be as specified in section 4 of MIL-STD-750. 4.5.2 Thermal resistance. The thermal resistance measurements shall be performed in accordance with method 3161 of MIL-STD-750 using the guidelines in that method for determining IM, IH, tH, tSW(and VHwhere appropriate). Measurement delay time (tMD) = 70 s max. See table E-IX of MIL-PRF-19500, group E, subgroup 4. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19500/751 9 TABLE I. G