DLA MIL-PRF-19207 10 F-2013 FUSEHOLDERS EXTRACTOR POST TYPE NONINDICATING TYPES FHN19G AND FHN19W.pdf

《DLA MIL-PRF-19207 10 F-2013 FUSEHOLDERS EXTRACTOR POST TYPE NONINDICATING TYPES FHN19G AND FHN19W.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-19207 10 F-2013 FUSEHOLDERS EXTRACTOR POST TYPE NONINDICATING TYPES FHN19G AND FHN19W.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5920 MIL-PRF-19207/10F 12 December 2013 SUPERSEDING MIL-PRF-19207/10E 24 April 2007 PERFORMANCE SPECIFICATION SHEET FUSEHOLDERS, EXTRACTOR POST TYPE, NONINDICATING, TYPES FHN19G AND FHN19W This specification is approved for use by all Departments and Agencies of the Department of Defens

2、e. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-19207. Ltr Inches mm Ltr Inches mm Min Max Min Max Min Max Min Max A .730 .770 18.54 19.56 F - 2.500 - 63.50 B .670 .710 17.02 18.03 G .560 .569 14.22 14.45 C .710 .750 18.03 19.05 H

3、.790 .830 20.07 21.08 D .480 .520 12.19 13.21 J .570 .575 14.47 14.61 E .100 - 2.54 - K .625 .635 15.88 16.13 See notes on page 2. FIGURE 1. Type FHN19G. Inactive for new design after 10 May 1974 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

4、-,-,-MIL-PRF-19207/10F 2 Ltr Inches mm Ltr Inches mm Min Max Min Max Min Max Min Max A .932 .957 23.67 24.31 F .558 .567 14.17 14.40 B .100 .140 2.54 3.56 G .920 .960 23.37 24.38 C .790 .830 20.07 21.08 H .570 .575 14.48 14.61 D .420 .460 11.08 11.68 J .625 .635 15.88 16.13 E 2.140 2.180 54.36 55.37

5、 NOTES: 1. Dimensions are in inches. 2. Metric equivalents (to the nearest .01 mm) are given for general information only and are based on 1 inch = 25.4 mm. 3. Unless otherwise specified, tolerances are .02 for two-place decimals and .005 for three-place decimals. 4. It is suggested that type MAI-60

6、, GDI-30F or SDG-F of American Society for Testing and Materials ASTM-D5948 be considered for meeting the cap and body molding material requirements of this specification. ASTM-D3935 is also suggested as guidance for cap material. 5. Gaskets and O-rings: It is suggested that gaskets and o-rings that

7、 meet class 3 of A-A-59588 be considered for use. FIGURE 2. Type FHN19W. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19207/10F 3 REQUIREMENTS: Interface and physical dimensions: See figures 1 and 2. Cap and body molding material: Cap and

8、body molding materials shall be selected to enable the fuseholder to meet the performance requirements of this specification. Additional information and guidance on body molding material are specified in the notes. Fuse accommodation: Ferrule type: Size: .281 inch diameter, 1.250 inch length. Style:

9、 F06: MIL-PRF-15160/6. (or equivalent size and style) Poles: One. Rating: 15 amperes, 250 volts maximum. Panel thickness: .187 inch maximum. Gaskets and o-rings shall be used that enable the fuseholder to meet the performance requirements of this specification. Additional information and guidance on

10、 gaskets and o-rings are specified in the notes. Nonindicating: Lamp series resistor: None. Terminals: Solder lug type. Enclosure: FHN19G: Dripproof. FHN19W: Watertight. Test fuses: Temperature rise: F06A250V15A of MIL-PRF-15160/6. Short circuit: F06A250V15A of MIL-PRF-15160/6. Short circuit test sh

11、all be made at 10,000 amperes,125 volts, 60 Hz and 200 amperes, 250 volts, 60 Hz. Mechanical shock: Method II of MIL-PRF-19207. Terminal strength: 5 pounds. Torque: Mounting - 30 inch-pounds. Cap insert (FHN19W only) - 15 inch-pounds. Salt spray (corrosion): Test condition B. Part or Identifying Num

12、ber (PIN): FHN19G or FHN19W depending on type.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19207/10F 4 Referenced documents. In addition to MIL-PRF-19207, this document references the following: MIL-PRF-15160/6 A-A-59588 ASTM-D3935 ASTM-D5

13、948 The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to e

14、valuate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing Activity: Army - CR DLA - CC Navy - SH Air force - 85 (Project 5920-2013-031) DLA - CC Review activities: Army - AR, CE, MI

15、Navy - AS, EC, MC Air Force - 19 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-