DLA MIL-DTL-83796 B-2008 HOSE ASSEMBLY RUBBER LIGHTWEIGHT MEDIUM PRESSURE GENERAL SPECIFICATION FOR《中等压力轻量橡胶软管组件的一般规范》.pdf
《DLA MIL-DTL-83796 B-2008 HOSE ASSEMBLY RUBBER LIGHTWEIGHT MEDIUM PRESSURE GENERAL SPECIFICATION FOR《中等压力轻量橡胶软管组件的一般规范》.pdf》由会员分享,可在线阅读,更多相关《DLA MIL-DTL-83796 B-2008 HOSE ASSEMBLY RUBBER LIGHTWEIGHT MEDIUM PRESSURE GENERAL SPECIFICATION FOR《中等压力轻量橡胶软管组件的一般规范》.pdf(15页珍藏版)》请在麦多课文档分享上搜索。
1、MIL-DTL-83796B 11 August 2008 SUPERSEDING MIL-DTL-83796A 18 September 2000 DETAIL SPECIFICATION HOSE ASSEMBLY, RUBBER, LIGHTWEIGHT, MEDIUM PRESSURE, GENERAL SPECIFICATION FOR This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This
2、 specification covers the requirements for hose assembly, rubber, lightweight, medium pressure. For use in fuel and lubricating oil systems operating at 200 to 1000 psi and at a temperature range -65F to 250F. 1.2 Part or Identifying Number (PIN). The PIN consists of the letter M, the basic specific
3、ation number, a letter for fitting size, a two digit number for hose assembly length, a number for length in eighths of an inch, letter for style, a two digit number for angle between elbows, and a letter for material/finish. M83796 /1 H 0308 2 F 06 TComments, suggestions, or questions on this docum
4、ent should be addressed to: Defense Supply Center, Columbus, Attn: DSCC-VAI, P.O. Box 3990, Columbus, OH 43218-3990, or emailed to FluidFlowdla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.
5、daps.dla.mil. Material/finish Angle between elbows to be specified in 5 increments, 30 / 5 = 06 Specification number Specification sheet number Size code (see table I) Length in inches (see 1.2.1) Length in eighths of an inch (see 1.2.1) Style (see 1.2.2) INCH-POUNDAMSC N/A FSC 4720 Provided by IHSN
6、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83796B 2 TABLE I. Size code. 1/ 2/ Dash number -03 -04 -05 -06 -08 -10 -12 -16 Size code B E F G H J K M Inches fraction 3/16 1/4 5/16 3/8 1/2 5/8 3/4 1 Inches decimal .188 .250 .313 .375 .500 .625 .750 1.000 H
7、ose OD reference mm 4.78 6.35 7.95 9.53 12.70 15.88 19.05 25.40 Dash number -20 -24 -32 Size code N P R Inches fraction 1 1/4 1 1/2 2 Inches decimal 1.250 1.500 2.000 Hose OD reference mm 31.75 38.10 50.80 1/ Dimensions are in inches. 2/ Metric equivalents are given for information only. 1.2.1 Lengt
8、hs of hose. Lengths of hose are represented by inches (00 through 99) and fractions in 1/8 inch increments (0 thru 7). 1.2.2 Styles. Styles are shown in the individual specification sheets. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4 or 5
9、of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specif
10、ied requirements documents cited in sections 3, 4 or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein.
11、Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-5606 - Hydraulic Fluid, Petroleum Base, Aircraft, Missile and Ordinance MIL-PRF-7808 - Lubricating Oil, Aircraft Turbine Engine, Synthetic Base MIL-
12、PRF-87257 - Hydraulic Fluid, Fire Resistant; Low Temperature, Synthetic Hydrocarbon Base, Aircraft and Missile MIL-PRF-83282 - Hydraulic Fluid, Fire Resistant, Synthetic Hydrocarbon Base Aircraft, Metric, NATO Code Number H-537 MIL-DTL-83797 - Hose, Rubber, Lightweight, Medium Pressure, General Spec
13、ification for MIL-DTL-83798 - Fitting, Rubber Hose, Lightweight, Medium Pressure, General Specification for Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83796B 3 (See supplement 1 for list of specification sheets.) DEPARTMENT OF DEFENSE ST
14、ANDARDS MIL-STD-130 - Identification Marking of U.S. Military Property MS20756 - Flange, Swivel, Retaining MS33786 - Fitting Installation, Flared Tube and Hose, Swivel (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order
15、 Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) DEFENSE SUPPLY CENTER COLUMBUS (DSCC) 08001 - Hose Assembly, Internal Support Coil, For Vacuum and Suction Hoses (Copies of these documents are available online at http:/www.dscc.dla.mil/programs/milspec/ or from the Defense Suppl
16、y Center Columbus, ATTN: VAI, P.O. Box 3990, Columbus, Ohio 43218-3990.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. AE
17、ROSPACE INDUSTRIES ASSOCIATION (AIA) NAS847 - Caps and Plugs, Protective, Dust and Moisture Seal (Copies of these documents are available online at http:/www.aia- or from the Aerospace Industries Association, 1000 Wilson Boulevard, Suite 1700, Arlington, VA 22209-3901.) ASTM INTERNATIONAL ASTM A249/
18、A249M - Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes ASTM D380 - Standard Test Methods for Rubber Hose (Copies of these documents are available online at http:/www.astm.org or from the ASTM International, P.O. Box C700, 100 Barr Harbor D
19、rive, West Conshohocken, PA 19428-2959.) NCSL INTERNATIONAL NCSL Z540.3 - Requirements for the Calibration of Measuring and Test Equipment (Copies of these documents are available online at http:/www.ncsli.org or from NCSL International 2995 Wilderness Place, Suite 107 Boulder, Colorado 80301-5404)
20、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83796B 4 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION (ISO) ISO 17025 - General requirements for the competence of testing and calibration laboratories (Copies of these documents are available
21、 online at http:/www.iso.ch or from the International Organization for Standardization American National Standards Institute, 11 West 42ndStreet, 13thFloor, New York, NY 10036.) SAE INTERNATIONAL SAE-AS1055 - Fire Testing of Flexible Hose, Tube Assemblies, Coils, Fittings, and Similar System Compone
22、nts SAE-AS1072 - Sleeve, Hose Assembly, Fire Protection SAE-AS1933 - Age Controls for Hose Containing Age-Sensitive Elastomeric Material SAE-AS4395 - Fitting End-Flared Tube Connection, Design Standard SAE-AS33514 - Fitting End, Standard Dimensions for, Flareless Tube Connection and Gasket Seal (Cop
23、ies of these documents are available online at http:/www.sae.org or from the SAE World Headquarters, 400 Commonwealth Drive, Warrendale, PA 15096-0001.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between this document and the references cite
24、d herein (except for related specification sheets) the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Specification sheets. The individual item requirements shall
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMILDTL83796B2008HOSEASSEMBLYRUBBERLIGHTWEIGHTMEDIUMPRESSUREGENERALSPECIFICATIONFOR 中等 压力 橡胶 软管 组件

链接地址:http://www.mydoc123.com/p-691252.html