DLA MIL-DTL-44048 H-2000 COATS CAMOUFLAGE PATTERN COMBAT《战斗迷彩大衣》.pdf

《DLA MIL-DTL-44048 H-2000 COATS CAMOUFLAGE PATTERN COMBAT《战斗迷彩大衣》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-44048 H-2000 COATS CAMOUFLAGE PATTERN COMBAT《战斗迷彩大衣》.pdf（25页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-DTL-44048H1INCH-POUNDMIL-DTL-44048H30 November 2000SUPERSEDINGMIL-C-44048G2 February 1995DETAIL SPECIFICATIONCOATS, CAMOUFLAGE PATTERN, COMBATThis document is approved for use by all departments and agencies of the Department of Defense.1. SCOPE1.1 Scope. This document covers the requirements fo

2、r camouflage pattern, single-breasted combatcoats.1.2 Classification. The coat shall be of the following types and sizes as specified (see 6.2).Type I - Woodland camouflage pattern cotton/nylon twill clothType II - Deleted (see 6.5)Type III - Deleted (see 6.5)Type IV - Deleted (see 6.5)Type V - Dele

3、ted (see 6.5)Type VI - Woodland camouflage pattern, nylon/cotton ripstopType VII - Desert camouflage pattern, nylon/cotton ripstopType VIII - Black 357, nylon/cotton ripstopType IX - Insect repellent treated, woodland camouflage pattern cotton/nylon twillType X - Insect repellent treated, woodland c

4、amouflage pattern nylon/cotton ripstopType XI - Insect repellent treated, desert camouflage pattern nylon/cotton ripstopType XII - Insect repellent treated, Black 357, nylon/cotton ripstopType XIII - Camouflage Green 483, nylon/cotton ripstopBeneficial comments (recommendations, additions, deletions

5、) and any data which may be of use inimproving this document should be addressed to : Defense Supply Center Philadelphia, Clothing andTextiles Directorate, Attn.: DSCP-CRFD, 700 Robbins Avenue, Bldg 6 Area D, Philadelphia, PA19111-5096, by using the Standardization Document Improvement Proposal (DD

6、Form 1426)appearing at the end of this document or by letter.AMSC N/A FSC 8415DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-44048H2SCHEDULE OF SIZESX-Small Sma

7、ll Medium Large X-Large XX-LargeXXX-ShortXX-Short XX-Short XX-ShortX-Short X-Short X-Short X-ShortShort Short Short ShortRegular Regular Regular Regular RegularLong Long Long Long LongX-Long X-Long X-Long X-Long X-LongXX-Long2. APPLICABLE DOCUMENTS2.1 General. The documents listed in this section ar

8、e specified in sections 3 and 4 of this specification.This section does not include documents cited in other sections of this specification or recommended foradditional information or as examples. While every effort has been made to ensure the completeness ofthis list, document users are cautioned t

9、hat they must meet all specified requirements cited in sections 3and 4 of this specification, whether or not they are listed.2.2 Government documents.2.2.1 Specifications, standards, and handbooks. The following specifications, standards, andhandbooks form a part of this document to the extent speci

10、fied herein. Unless otherwise specified, theissues of these documents shall be those listed in the issue of the Department of Defense Index ofSpecifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2).SPECIFICATIONSMILITARYMIL-C-44031 - Cloth, Camouflage Patter

11、n: Woodland, Cotton and NylonMIL-DTL-44411 - Insect Repellent, PermethrinMIL-C-44436 - Cloth, Camouflage Pattern, Wind Resistant Poplin,Nylon/Cotton Blend(Copies of above specifications are available from the Defense Automated Printing Service, 700Robbins Avenue, Building #4, Section D, Philadelphia

12、, PA 19111-5096.)2.2.2 Other Government documents, drawings, and publications. The following Governmentdocuments, drawings, and publications form a part of this document to the extent specified herein.Unless otherwise specified, the issues are those specified in the solicitation.Provided by IHSNot f

13、or ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-44048H3Environmental Protection AgencyOffice of Prevention, Pesticides and Toxic Substances870.1200 (Acute Dermal Toxicity)(Copies may be obtained from the U.S. Government Printing Office, Washington DC 20402,or fr

14、om the Environmental Protection Agency at (800) 490-9198)2.3 Non-Government publications. The following documents form a part of this document to the extentspecified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shallbe those in the issue of the DODISS cited i

15、n the solicitation. Unless otherwise specified, the issues ofdocuments not listed in the DODISS are the issue of the documents cited in the solicitation (see 6.2).AMERICAN SOCIETY FOR TESTING AND MATERIALSASTM D-2256 - Tensile Properties of Yarns by the Single-Strand MethodASTM D-5034 - Breaking For

16、ce and Elongation of Textile Fabrics (Grab Test)ASTM D-6193 - Standard Practice for Stitches and Seams(Applications for copies should be addressed to the American Society for Testing andMaterials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.)AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND C

17、OLORISTSAATCC 61 - Colorfastness to Laundering, Home and Commercial: AcceleratedAATCC 136 - Bond Strength of Bonded and Laminated Fabrics(Applications for copies should be addressed to the American Association of Textile Chemistsand Colorists, P.O. Box 12215, Triangle Park, NC 27709-2215. Phone numb

18、er (919) 549-8141.)ANSI/ASQC Z1.4- Sampling Procedures and Tables for Inspection of Attributes(Applications for copies should be addressed to the American National Standards Institute,1430 Broadway, New York, NY 10018-3308.)Principle and Methods of Toxicology, A. Wallace Hayes (editor), 1989, pp.394

19、-396.(Applications for copies should be addressed to Raven Press, 1185 Avenue of the Americas,New York, NY 10036.)2.4 Order of precedence. In the event of a conflict between the text of this document and thereferences cited herein, the text of this document takes precedence. Nothing in this document

20、 however,supersedes applicable laws and regulations unless a specified exemption has been obtained.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-44048H43. REQUIREMENTS3.1 First article. When specified (see 6.2), a sample shall be subjected

21、to first article inspection (see6.3) in accordance with 4.2.3.2 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, orenvironmentally preferable materials should be used to the maximum extent possible provided that thematerial meets or exceeds the operational and maint

22、enance requirements, and promotes economicallyadvantageous life cycle costs.3.3 Design and construction. The coat is single-breasted with a collar, concealed button front closureand four bellowed pockets with flaps having concealed buttons. Each breast pocket has a drainagehole in the bottom bellows

23、; the left pocket has a concealed pencil pocket. The coat has long sleeveswith reinforced elbows, adjustable cuffs at wrist, a suppressed waist and straight-cut bottom (referencefigure 1). This design provides for comfort in movement and uniformity between manufacturers.3.3.1 Basic material. The fol

24、lowing materials shall be used to provide the comfort and durabilityneeded in garrison, combat, and operations other than war. The coat shall show no toxicity when usedas intended and when tested as specified in 4.4.Types I and IX - The basic material shall be cotton/nylon twill cloth printed in woo

25、dlandcamouflage pattern conforming to class 1 of MIL-C-44031.Types VI and X - The basic material shall be nylon/cotton ripstop printed in woodlandcamouflage pattern conforming to class 1 of MIL-C-44436.Types VII and XI- The basic material shall be nylon/cotton ripstop printed in a desertcamouflage p

26、attern conforming to class 3 of MIL-C-44436.Types VIII and XII - The basic material shall be nylon/cotton ripstop dyed Black 357,conforming to class 5 of MIL-C-44436.Type XIII - The basic material shall be nylon/cotton ripstop dyed Camouflage Green 483,conforming to class 5 of MIL-C-44436.3.3.2 Grou

27、nd shade/printed seconds/mill seconds. Ground shade cloth shall be dyed in conformancewith the specified basic material and shall meet the physical, mechanical, and dimensional requirementsof the respective finished fabric. Printed seconds shall be cloth which has only been rejected for defectsperta

28、ining to color, infrared reflectance, or camouflage print patterns, cited in the specified basic materialrequirements. Mill seconds shall be cloth which has been rejected for visual defects only and has beeneither dyed to match ground shade or printed with a camouflage pattern (see 3.4.2).Provided b

29、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-44048H53.3.3 Interlining. To improve abrasion resistance and appearance of garment, the collar and pocketflaps of all coat types shall be interlined. The interlining shall have the same life expectancy of

30、 the coatitself, and after attaching to the basic cloth, shall meet an initial directional bond strength of 32 ouncesminimum per inch and 24 ounces minimum per inch after 3 launderings when tested as specified in 4.4.1.3.3.4 Thread. Thread for needle and bobbin (looper) shall be cotton- or polyester

31、-covered, polyestercore, commercial size Ticket No. 50 (Tex size 36 to 50) with a minimum breaking strength of 3.2pounds when tested as specified in 4.4.2. As an alternate, Ticket No. 70 (Tex size 31 to 35) with abreaking strength of 2.6 pounds when tested as specified in 4.4.2 may be used as the bo

32、bbin (looper)thread.3.3.4.1 Gimp. Thread for reinforcement of buttonholes shall be cotton, commercial size Ticket No. 8(Tex size 210) with a minimum breaking strength of 6.5 pounds when tested as specified in 4.4.2. Thesize and type of gimp specified provides durability and shape retention to the ey

33、elet end buttonhole.3.3.4.2 Colorfastness and Color. All thread used shall be non-staining and show good colorfastness tolaundering when tested as specified in 4.4.3. The thread shall be a good match to the following colors:Types I,VI, IX, X and XIII Types VII and XI Types VIII and XIICamouflage Gre

34、en (CG) 483 Light Khaki 494 Black 3573.3.5 Insect Repellent. The finished coats, types IX, X, XI, XII only, shall be given an EPA approvedpermethrin treatment. This process shall be performed on the completed coats. The treated coats shallcontain 0.113 to 0.137 mg/cm2 of permethrin with a standard d

35、eviation of 0.036 to 0.044 when testedin accordance with the gas chromatographic method specified in 4.4.8.3.3.5.1 Permethrin. The permethrin (US patent No. 4,024,163) used shall conform to type II of MIL-DTL-44411.3.3.6 Labels. Each coat shall have a size label, an identification label, a care labe

36、l, and an insectrepellent label (types IX, X, XI, XII only), as applicable. The size and identification labels or theidentification and care label may be combined. The identification label shall contain the item description,contract number, fiber content information and contractors name. The label c

37、olor shall approximate thebasic cloth ground shade for the size, identification and care labels, with the exception of types VIII andXII, which shall be white. The insect repellent label shall be yellow in color. The inscription shall have aminimum font size of 10 points. The inscription legibility,

38、 label, and label attachment shall last theexpected life of the coat. The care label, combination label, or insect repellent label, as applicable, shallinclude the following information:Types I and IX - Coat, Woodland Camouflage Pattern, CombatorTypes VI and X - Coat, Hot Weather, Woodland Camouflag

39、e Pattern, CombatProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-44048H6orTypes VII and XI- Coat, Desert Camouflage Pattern, CombatorTypes VIII and XII- Coat, Hot weather, Black, CombatType XIII- Coat, Hot weather, Camouflage Green, Combat1.

40、Wear outside of trousers.2. Adjust closures to ventilate: avoid overheating of body.3. Machine washing. Use Permanent Press Cycle. Wash in warm water andmild detergent.4. Hand washing. Wash in warm water using mild detergent.DO NOT WRING OR TWIST. Rinse in clean warm water.5. DO NOT USE CHLORINE BLE

41、ACH OR STARCH.6. Dry at low heat (Do not exceed 130oF). After drying, tumble at roomtemperature for 10 minutes. Remove immediately from dryer. To dripdry, remove from water and place on rust-proof hanger.DO NOT REMOVE THIS LABEL3.3.6.1 Insect repellent label. For types IX, X, XI, and XII coats only.

42、 This label shall contain all theinformation on the existing size or combination label and the following information shall also be includedon the yellow colored insect repellent label:This garment has been treated with Permethrin insect repellent.Date of treatment: (insert date)Dosage Rate: (insert

43、rate)3.3.6.2 Size label. The size label shall contain, as a minimum, the following information, as applicable:X-Small - XX-Short X-Small X-Short X-Small - ShortHeight: 55 to 59 in. Height: 59 to 63 in. Height: 63 to 67 in.Chest: Up to 33 in. Chest: Up to 33 in. Chest: Up to 33 in.Stock No. Stock No.

44、 Stock No.NATO Size 4050/7484 NATO Size 5060/7484 NATO Size 6070/7484X-Small Regular X-Small - Long Small XXX-ShortHeight: 67 to 71 in. Height: 71 to 75 in. Height: Under 55 in.Chest: Up to 33 in. Chest: Up to 33 in. Chest: 33 to 37 in.Stock No. Stock No. Stock No.NATO Size 7080/7484 NATO Size 8090/

45、7484 NATO Size 3040/8494Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-44048H7Small XX-Short Small - X-Short Small ShortHeight: 55 to 59 in. Height: 59 to 63 in. Height: 63 to 67 in.Chest: 33 to 37 in. Chest: 33 to 37 in. Chest: 33 to 37 in.

46、Stock No. Stock No. Stock No.NATO Size 4050/8494 NATO Size 5060/8494 NATO Size 6070/8494Small - Regular Small - Long Small - X-LongHeight: 67 to 71 in. Height: 71 to 75 in. Height: Above 75 in.Chest: 33 to 37 in. Chest: 33 to 37 in. Chest: 33 to 37 in.Stock No. Stock No. Stock No.NATO Size 7080/8494

47、 NATO Size 8090/8494 NATO Size 9000/8494Medium XX-Short Medium - X-Short Medium - ShortHeight: 55 to 59 in. Height: 59 to 63 in. Height: 63 to 67 in.Chest: 37 to 41 in. Chest: 37 to 41 in. Chest: 37 to 41 in.Stock No. Stock No. Stock No.NATO Size 4050/9404 NATO Size 5060/9404 NATO Size 6070/9404Medi

48、um Regular Medium - Long Medium - X-LongHeight: 67 to 71 in. Height: 71 to 75 in. Height: 75 to 79 in.Chest: 37 to 41 in. Chest: 37 to 41 in. Chest: 37 to 41 in.Stock No. Stock No. Stock No.NATO Size 7080/9404 NATO Size 8090/9404 NATO Size 9000/9404Large - X-Short Large - Short Large - RegularHeight

49、: 59 to 63 in. Height: 63 to 67 in. Height: 67 to 71 in.Chest: 41 to 45 in. Chest: 41 to 45 in. Chest: 41 to 45 in.Stock No. Stock No. Stock No.NATO Size 5060/0414 NATO Size 6070/0414 NATO Size 7080/0414Large - Long Large - X-Long Large - XX-LongHeight: 71 to 75 in. Height: 75 to 79 in. Height: Above 79 in.Chest: 41 to 45 in. Chest: 41 to 45 in. Chest: 41 to 45 inStock No. Stock No. Stock No.NATO Size 8090/0414 NATO Size 9000/0414 NATO Size 0010/0414X-L