DLA MIL-DTL-32385 5-2011 CONNECTOR PLUG CENTER CONTACT POSITIVE EMBEDDED APPLICATION [Superseded NAVY MS90335 REV D NAVY MS90335 REV C NAVY MS90335 REV B NAVY MS90335 REV A DLA MS9.pdf

《DLA MIL-DTL-32385 5-2011 CONNECTOR PLUG CENTER CONTACT POSITIVE EMBEDDED APPLICATION [Superseded NAVY MS90335 REV D NAVY MS90335 REV C NAVY MS90335 REV B NAVY MS90335 REV A DLA MS9.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-32385 5-2011 CONNECTOR PLUG CENTER CONTACT POSITIVE EMBEDDED APPLICATION [Superseded NAVY MS90335 REV D NAVY MS90335 REV C NAVY MS90335 REV B NAVY MS90335 REV A DLA MS9.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5935 INCH-POUND MIL-DTL-32385/5 14 July 2011 SUPERSEDING MS90335D 5 January 1996 DETAIL SPECIFICATION SHEET CONNECTOR, PLUG, CENTER CONTACT POSITIVE, EMBEDDED APPLICATION This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirement

2、s for acquiring the product described herein shall consist of this specification sheet, MIL-DTL-32385, and QPL-32385. INTENDED USE: 1. The connector covered by this specification sheet is intended for use on control and instrument panels for aircraft, ground, and shipboard applications. REQUIREMENTS

3、: 1. Material: Material shall be in accordance with MIL-DTL-32385. 2. Finish: Finish shall be in accordance with MIL-DTL-32385. 3. Design: Design shall be in accordance with MIL-DTL-32385. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32385

4、/5 2 NOTES: 1. The part or identifying number (PIN) consists of the letters MS, the specification number, and the dash number taken from table 1. MS 90335 - X Dash number (see table I) Specification number MS prefix (Retaining MS part number) TABLE I. Dash number PIN cross-reference data. Dash numbe

5、r MS90335D PIN MIL-DTL-32385/5 PIN -7 MS90335-7 MS90335-7 2. Interpret figure in accordance with ASME Y14.5. 3. Collar shall have a minimum of four slots and a maximum of six slots. 4. The current loading of the connectors is limited to the current-carrying capacity of the wire used in the associate

6、d interconnecting cabling. 5. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. 6. Unless otherwise specified, issues of reference documents are those in effect at the time of solicitation. 7. Interchangeability

7、relationship: MS90335-7 and MIL-DTL-32385/5 parts are universally, functionally and dimensionally interchangeable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32385/5 3 NOTES: 1. All dimensions are in inches. 2. Tolerances: Dimensions 0.0

8、05 unless otherwise specified. FIGURE 1. Connector, plug, center contact positive, embedded application. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32385/5 4 Custodians: Preparing Activity: Army - AV Navy - AS Air Force - 85 DLA - GS DLA

9、 - GS2 (Project 5935-2011-035) Review Activities: Navy - MC, SH NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-