DLA MIL-DTL-27434 28 A-2008 ADAPTER CONNECTOR COAXIAL RADIOFREQUENCY BETWEEN SERIES SERIES BNC to SERIES QDS TYPE UG-1136 U.pdf

《DLA MIL-DTL-27434 28 A-2008 ADAPTER CONNECTOR COAXIAL RADIOFREQUENCY BETWEEN SERIES SERIES BNC to SERIES QDS TYPE UG-1136 U.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-27434 28 A-2008 ADAPTER CONNECTOR COAXIAL RADIOFREQUENCY BETWEEN SERIES SERIES BNC to SERIES QDS TYPE UG-1136 U.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-DTL-27434/28A 22 May 2008 SUPERSEDING MIL-A-27434/28 28 September 1960 DETAIL SPECIFICATION SHEET ADAPTER, CONNECTOR, COAXIAL, RADIOFREQUENCY, BETWEEN SERIES, SERIES BNC to SERIES QDS TYPE UG-1136/U This specification is approved for use by all Departments and Agencies of the Department of Defen

2、se The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-27434. FIGURE 1. Type UG1136/U connector adapter. AMSC N/A FSC 5935 Inactive for new design after 19 February 1982 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networkin

3、g permitted without license from IHS-,-,-MIL-DTL-27434/28A 2 ENGINEERING DATA: Impedance: 50 ohms, nominal. Frequency range: Frequency range: 0 to 2 GHz. Voltage rating: 500 V rms, maximum at sea level. 125 V rms, maximum at 70,000 feet. Temperature rating: -65 C to +165 C. REQUIREMENTS: Dimensions

4、and configuration: See figure 1. Mating characteristics: Series BNC pin contact in accordance with MIL-STD-348, and series QDS socket contact interface shall be in accordance with MIL-DTL-27434 after assembly. Contact gage test (series QDS only): The center contact shall be subjected to the followin

5、g gage test prior to assembly into the adapter. The pins that are used in the performance of these tests may be tapered at theirs ends to facilitate insertion, but the tapered portions shall not be included in the specified dimensions. A pin 0.100 inch minimum in diameter shall be inserted to a dept

6、h of 0.125 inch minimum, and then removed. The contact shall be then tested as follows: a. A pin 0.074 inch minimum in diameter shall be inserted to a depth of 0.200 inch minimum shall not deflect the contact members. b. A pin 0.080 inch maximum in diameter inserted to depth of 0.125 inch minimum sh

7、all make contact with all four contact members within 0.015 inch of their tip ends. c. A pin 0.093 inch minimum in diameter inserted to a depth of 0.062 inch minimum shall not cause the contact members to bow perceptibly. Dielectric withstanding voltage: Method 301 of MIL-STD-202, 1,500 V rms minimu

8、m at sea level. Corrosion: Applicable. Vibration: Applicable. Shock: Applicable. Part or Identifying Number (PIN): UG-1136/U. Supersession: This document supersedes drawing REB49306. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the

9、 previous issue due to the extent of the changes. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-27434/28A 3 Referenced documents. In addition to MIL-DTL-27434, this document references the following: MIL-STD-202 MIL-STD-348 REA10399 REA1044

10、9 REB10225 REB10879 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5935-2007-011) DLA - CC NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-