DLA MIL-DTL-27072 70 B-2012 CABLE SPECIAL PURPOSE ELECTRICAL SHIELDED TYPE I STYLE 1 4 CONDUCTORS M27072 70MACA.pdf

《DLA MIL-DTL-27072 70 B-2012 CABLE SPECIAL PURPOSE ELECTRICAL SHIELDED TYPE I STYLE 1 4 CONDUCTORS M27072 70MACA.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-27072 70 B-2012 CABLE SPECIAL PURPOSE ELECTRICAL SHIELDED TYPE I STYLE 1 4 CONDUCTORS M27072 70MACA.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 6145 INCH-POUND MIL-DTL-27072/70B 12 March 2012 SUPERSEDING MIL-DTL-27072/70A8 December 2000 DETAIL SPECIFICATION SHEET CABLE, SPECIAL PURPOSE, ELECTRICAL, SHIELDED; TYPE I, STYLE 1, 4 CONDUCTORS, M27072/70MACA* This specification is approved for use by all Departments and Agencies of

2、the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-27072. REQUIREMENTS: TAPE POLYETHYLENE TEREPHALATESHIELD TINNED COPPERSHEATH POLYVINYL CHLORIDE WHITE/BROWNBLACK WHITEYELLOWFILLERNOTE: The complete Part or Id

3、entifying Number (PIN) requires a color code designator (see table I). FIGURE 1. Cable configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-27072/70B 2 Design and construction: See figure 1 Number or conductors: 4 Temperature rating

4、: 105 C Components: Basic wire: M16878/17BFB* (see table I) Conductor: Tinned copper Primary insulation: Polyvinyl chloride Colors: Black White Yellow White/brown Jacket over insulation: Polyamide Color: Natural (clear) Filler: Material: In accordance with MIL-DTL-27072 Lay: 1.75 inches Cabling: Not

5、 applicable Binder tape material: Polyethylene terephalate Shield: Material: Tinned copper Gauge: 36 AWG Braid angle: 20 to 40 degrees Jacket undershield: Not applicable Sheath: Material: Polyvinyl chloride Wall thickness: .065 inch nominal Tensile strength: In accordance with MIL-DTL-27072 Ultimate

6、 elongation: In accordance with MIL-DTL-27072 Accelerated aging: In accordance with MIL-DTL-27072 Color: See MIL-DTL-27072 Finished cable: See table I Cold bend: Mandrel size in accordance with MIL-DTL-27072 Dielectric withstanding voltage: 2,000 V rms Conductor resistance: In accordance with basic

7、wire specification TABLE I. Construction data. PIN 27072/70 Basic wire except color M16878/17BFB* 1/,2/(reference) Finished cable diameter inch (mm) 10% Wire size (AWG) Number of strands Strand size Nominal diameter inch (mm) MACA 22 7 30 .056(1.42) .312(7.92) 1/ Asterisks (*) shall be replaced by t

8、he appropriate color designator. 2/ Dimensions are in inches. Metric equivalents are given for information only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-27072/70B 3 Changes from previous issue: Marginal notations are not used in this

9、revision to identify changes with respect to the previous issues due to the extensiveness of the changes. Referenced document. This document references MIL-DTL-27072. CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - SH Air Force - 85 (Project 6145-2012-013) DLA CC NOTE:

10、The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of this information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-