DLA MIL-DTL-15370 10 E-2012 COUPLERS DIRECTIONAL (COAXIAL SMA CONNECTORS) ( 50 to 18 GHz).pdf

《DLA MIL-DTL-15370 10 E-2012 COUPLERS DIRECTIONAL (COAXIAL SMA CONNECTORS) ( 50 to 18 GHz).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-15370 10 E-2012 COUPLERS DIRECTIONAL (COAXIAL SMA CONNECTORS) ( 50 to 18 GHz).pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5985 MIL-DTL-15370/10E 22 October 2012 SUPERSEDING MIL-DTL-15370/10D 7 May 2008 DETAIL SPECIFICATION SHEET COUPLERS, DIRECTIONAL (COAXIAL, SMA CONNECTORS) (.50 to 18 GHz) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirement

2、s for acquiring the couplers described herein shall consist of this specification sheet and MIL-DTL-15370. Inches mm .010 0.25 .093 2.36 FIGURE 1. Dimensions and configuration for part numbers M15370/10-001 through M15370/10-011, and M15370/10-019. INCH-POUND Provided by IHSNot for ResaleNo reproduc

3、tion or networking permitted without license from IHS-,-,-MIL-DTL-15370/10E 2 Inches mm .015 0.38 .125 3.18 .38 9.65 FIGURE 2. Dimensions and configuration for part number M15370/10-012. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15370/1

4、0E 3 Inches mm .003 0.08 .105 2.67 .38 9.65 FIGURE 3. Dimensions and configuration for part numbers M15370/10-013, M15370/10-021, M15370/10-023, and M15370/10-024. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15370/10E 4 Inches mm .003 0.0

5、8 .105 2.67 .38 9.7 NOTES: 1. Sealant thickness, .031 maximum for dash numbers M15370/10-016, M15370/10-017, and M15370/10-018. 2. Four mounting holes are permitted, providing they are symmetrical with the two holes shown. FIGURE 4. Dimensions and configuration for part numbers M15370/10-014 through

6、 M15370/10-018, and M15370/10-020. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15370/10E 5 Inches mm .010 .25 .140 3.56 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. FIGURE 5. Dimensions and con

7、figuration for part numbers M15370/10-022, M15370/10-025, M15370/10-026, and M15370/10-028 through M15370/10-030. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15370/10E 6 Inches mm .003 0.08 .105 2.67 .38 9.7 FIGURE 6. Dimensions and confi

8、guration for part number M15370/10-027. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Dimensions and physical requirements. Dash No. Mounting config-uration (figure) Dimensions 1/ 2/ 3/ Weight (max) A (max) B .005 (0.13) C .02 (0.51) D .02

9、0 E .02 (0.51) F (max) G (max) H .02 (0.51) J (max) K +.010 -.000 L .010 M (max) lbs g oz 001 1 3.320 (84.33) 3.130 (79.50) 2.710 (68.83) .290 (7.37) 1.495 (37.97) .530 (13.46) .405 (10.29) .580 (14.73) - - .080 (2.03) - .16 71 2.5 002 1 3.320 (84.33) 3.130 (79.50) 2.710 (68.83) .290 (7.37) 1.495 (3

10、7.97) .530 (13.46) .405 (10.29) .580 (14.73) - - .080 (2.03) - .16 71 2.5 003 1 3.320 (84.33) 3.130 (79.50) 2.710 (68.83) .290 (7.37) 1.495 (37.97) .530 (13.46) .405 (10.29) .580 (14.73) - - .080 (2.03) - .16 71 2.5 004 1 2.563 (65.10) 2.391 (60.73) 1.954 (49.63) .290 (7.37) 1.495 (37.97) .530 (13.4

11、6) .405 (10.29) .580 (14.73) - - .080 (2.03) - .16 71 2.5 005 1 2.563 (65.10) 2.391 (60.73) 1.954 (49.63) .290 (7.37) 1.495 (37.97) .530 (13.46) .405 (10.29) .580 (14.73) - - .080 (2.03) - .16 71 2.5 006 1 2.563 (65.10) 2.391 (60.73) 1.954 (49.63) .290 (7.37) 1.495 (37.97) .530 (13.46) .405 (10.29)

12、.580 (14.73) - - .080 (2.03) - .16 71 2.5 007 1 1.715 (43.56) 1.525 (38.74) 1.105 (28.07) .290 (7.37) 1.495 (37.97) .530 (13.46) .405 (10.29) .580 (14.73) - - .080 (2.03) - .16 71 2.5 008 1 1.210 (30.73) 1.020 (25.91) .600 (15.24) .290 (7.37) 1.495 (37.97) .530 (13.46) .405 (10.29) .580 (14.73) - -

13、.080 (2.03) - .06 29 1.02 009 1 1.100 (27.94) .920 (23.37) .500 (12.70) .290 (7.37) 1.620 (41.15) .655 (16.64) .405 (10.29) .642 (16.31) - - .080 (2.03) - .06 29 1.02 010 1 1.100 (27.94) .920 (23.37) .500 (12.70) .290 (7.37) 1.620 (41.15) .655 (16.64) .405 (10.29) .642 (16.31) - - .080 (2.03) - .06

14、29 1.02 011 1 1.100 (27.94) .920 (23.37) .500 (12.70) .290 (7.37) 1.620 (41.15) .655 (16.64) .405 (10.29) .642 (16.31) - - .080 (2.03) - .06 29 1.02 012 2 1.560 (39.62) .375 4/ (9.53) 1.090 5/ (27.69) .220 5/ (5.59) - .843 5/ (21.41) .530 (13.46) .605 5/ (15.37) .281 4/ (7.14) .130 (3.30) .770 5/ (1

15、9.56) 1.380 (35.05) .16 71 2.5 013 3 1.040 (26.42) - .500 5/ (12.70) .250 5/ (6.35) - .843 5/ (21.41) .415 (10.54) - .410 5/ (10.41) .125 (3.18) .521 5/ (13.23) .800 (20.32) .08 29 1.02 014 4 3.20 (81.3) 1.500 (38.10) 2.700 (68.58) .270 (6.86) 1.45 (36.8) .800 (20.32) .415 (10.54) - .585 (14.86) .08

16、0 (2.03) .800 (20.32) .650 (16.5) .46 207 7.3 015 4 3.030 (76.96) 1.000 (25.40) 2.500 (63.50) .270 (6.86) 1.00 (25.4) .750 (19.05) .415 (10.54) - .440 (11.17) .110 (2.79) 1.013 (25.73) .250 (6.35) .09 43 1.5 016 4 3.050 (77.47) 1.500 (38.10) 2.520 (64.01) .270 (6.86) 1.00 (25.4) .590 (14.99) .415 (1

17、0.54) - .340 (8.64) .110 (2.79) .790 (20.06) .470 (11.93) .09 43 1.5 017 4 3.050 (77.47) 1.750 (44.45) 2.500 (63.50) .270 (6.86) 1.00 (25.4) .530 (13.46) .415 (10.54) - .300 (7.62) .110 (2.79) .650 (16.51) .470 (11.94) .09 43 1.5 018 4 3.050 (77.47) 1.750 (44.45) 2.500 (63.50) .270 (6.86) 1.00 (25.4

18、) .530 (13.46) .415 (10.54) - .300 (7.62) .110 (2.79) .650 (16.51) .470 (11.93) .09 43 1.5 019 1 2.651 (67.34) 2.391 (60.73) 1.969 (50.01) .385 (9.78) 1.628 (41.35) .530 (13.46) .415 (10.54) .578 (14.68) - - .125 (3.18) - .09 43 1.5 020 4 1.200 (30.48) .340 (8.64) .660 (16.76) .270 (6.86) 1.45 (36.8

19、) .800 (20.32) .415 (10.54) - .585 (14.85) .080 (2.03) .410 (10.41) .650 (16.51) .46 207 7.3 See footnotes at end of table. 7MIL-DTL-15370/10EProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Dimensions and physical requirements - Continued. D

20、ash Number Mounting configuration (figure) Dimensions 1/ 2/ 3/ Weight (max) A (max) B .005 (0.13) C .02 (0.51) D .020 E .02 (0.51) F (max) G (max) H .02 (0.51) J (max) K +.010 -.000 L .010 M (max) lbs g oz 021 3 1.04 (26.4) - .50 (12.7) .25 (6.4) - .54 (13.7) .44 (11.2) - .30 (7.6) .110 (2.79) .520

21、(13.20) .75 (19.1) .04 17 0.60 022 5 2.02 (51.3) 1.75 (44.5) - .30 (7.6) - 1.27 (32.3) .44 (11.2) - .30 (7.6) .625 (15.87) .125 (3.18) .35 (8.9) .09 43 1.5 023 3 1.04 (26.4) - .50 (12.7) .25 (6.4) - .50 (12.7) .395 (10.0) - .30 (7.6) .093 (2.36) .507 (12.87) .06 (1.5) .19 85 3.0 024 3 1.04 (26.4) -

22、.50 (12.7) .25 (6.4) - .54 (13.7) .395 (10.0) - .30 (7.6) .093 (2.36) .521 (13.23) .812 (20.62) .04 17 0.60 025 5 2.02 (51.3) 1.75 (44.5) - .25 (6.4) 2.0 (51.) 1.6 (41.) .395 (10.0) - .30 (7.6) .625 (15.87) .125 (3.18) .40 (10.2) .09 43 1.5 026 5 2.02 (51.3) 1.75 (44.5) - .25 (6.4) 2.0 (51.) 1.6 (41

23、.) .395 (10.0) - .30 (7.6) .625 (15.87) .125 (3.18) .40 (10.2) .09 43 1.5 027 6 1.04 (25.4) - - .250 (6.35) - .50 (12.7) .395 (10.0) - .30 (7.6) .093 (2.36) .500 (12.70) - .06 28 1.0 028 5 2.02 (51.3) 1.75 (44.5) - .35 (8.9) - 1.27 (32.3) .44 (11.2) - .30 (7.6) .625 (15.87) .125 (3.18) .35 (8.9) .09

24、 43 1.5 029 5 2.02 (51.3) 1.75 (44.5) - .30 (7.6) - 1.27 (32.3) .44 (11.2) - .30 (7.6) .625 (15.87) .125 (3.18) .35 (8.9) .09 43 1.5 030 5 2.02 (51.3) 1.75 (44.5) - .30 (7.6) - 1.27 (32.3) .44 (11.2) - .30 (7.6) .625 (15.87) .125 (3.18) .35 (8.9) .09 43 1.5 1/ Dimensions are in inches. 2/ Metric equ

25、ivalents are given for general information only. 3/ Metric equivalents are in parentheses. 4/ Tolerance is .010 (0.25). 5/ Tolerance is .030 (0.76). 8MIL-DTL-15370/10EProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE II. Electrical requirements.

26、Dash number Frequency range Coupling (dB) Coupling variation (dB) max Effective directivity (dB) min Insertion loss (dB) max VSWR max RF input power to primary Reflected power (avg) max Nominal Tolerance Primary line Secondary line Over frequency range Avg Peak GHz Watts Watts KW Watts 001 0.5 - 1.0

27、 6 1.0 0.6 20 0.2 1.25:1 1.25:1 50 50 0.25 2 002 0.5 - 1.0 10 1.0 0.75 20 0.2 1.25:1 1.25:1 50 50 0.25 5 003 0.5 - 1.0 20 1.0 1.0 20 0.2 1.25:1 1.25:1 50 50 0.25 50 004 1.0 - 2.0 6 1.0 0.5 20 0.2 1.25:1 1.25:1 50 50 0.25 2 005 1.0 - 2.0 10 1.0 0.75 20 0.2 1.25:1 1.25:1 50 50 0.25 5 006 1.0 - 2.0 20

28、1.0 1.0 20 0.2 1.20:1 1.20:1 50 50 0.25 50 007 2.0 - 4.0 6 1.0 0.5 18 0.2 1.20:1 1.20:1 50 50 0.25 2 008 4.0 - 8.0 6 1.0 0.5 18 0.2 1.20:1 1.20:1 50 50 0.25 2 009 8.0 - 12.4 10 1.0 0.5 15 0.25 1.30:1 1.30:1 50 50 0.25 2 010 8.0 - 12.4 20 1.0 0.75 15 0.25 1.30:1 1.30:1 50 50 0.25 2 011 12.4 - 18.0 6

29、1.0 0.5 12 0.25 1.35:1 1.35:1 50 50 0.25 2 012 7.0 - 11.0 10 1.0 0.75 15 0.85 1.25:1 1.25:1 100 100 2.0 10 013 7.0 - 11.0 20 1.0 1.0 15 0.40 1.25:1 1.30:1 100 100 2.0 100 014 1/ 0.5 - 1.0 10 1.25 0.75 25 0.20 1.10:1 1.10:1 50 50 3.0 5 015 0.5 - 1.0 30 1.0 0.75 25 0.15 1.10:1 1.10:1 50 50 4.0 50 016

30、0.5 - 1.0 10 1.0 0.75 25 0.2 1.15:1 1.15:1 50 50 3.0 5 017 0.5 - 1.0 20 1.0 0.75 25 0.2 1.15:1 1.15:1 50 50 3.0 50 018 0.5 - 1.0 30 1.0 0.75 25 0.2 1.15:1 1.15:1 50 50 3.0 50 019 1.5 - 1.9 15 1.0 0.75 20 0.2 1.20:1 1.20:1 5 5 2.0 2 020 2/ 2.0 - 4.0 6 1.0 0.5 20 0.2 1.30:1 1.30:1 50 50 2.0 2 See foot

31、notes at end of table. 9MIL-DTL-15370/10EProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE II Electrical requirements - Continued. Dash number Frequency range Coupling (dB) Coupling variation (dB) max Effective directivity (dB) min Insertion loss

32、 (dB) max VSWR max RF input power to primary Reflected power (avg) max Nominal Tolerance Primary line Secondary line Over frequency range Avg Peak GHz Watts Watts KW Watts 021 2.6 - 5.2 20 1.25 0.75 20 0.25 1.25:1 1.25:1 50 50 3.0 50 022 3/ 2.6 - 5.2 20 1.25 0.75 20 0.25 1.25:1 1.25:1 50 50 7.5 50 0

33、23 4.4 - 5.0 10 0.45 0.2 20 0.2 1.25:1 1.25:1 20 20 2 1 024 7.0 - 11.0 6 1.0 0.6 17 0.5 1.30:1 1.30:1 50 50 3 2 025 8.75 - 9.65 6 0.5 0.3 17 0.3 1.20:1 1.20:1 1 1 1 2 026 8.75 - 9.65 30 1.0 0.5 17 0.3 1.20:1 1.20:1 1 1 1 50 027 9.0 - 9.2 20 0.6 0.3 18 0.4 1.35:1 1.35:1 50 50 1 20 028 4/ 8.0 - 12.4 1

34、0 1.0 0.5 15 0.3 1.30:1 1.30:1 5 5 5 2 029 8.0 - 12.4 25 0.5 0.3 20 0.3 1.25:1 1.25:1 35 35 5 50 030 8.0 - 12.4 30 1.0 0.5 20 0.3 1.25:1 1.25:1 35 5 5 50 1/ Inactive for new design, use dash number -002 for new design. 2/ Inactive for new design, use dash number -007 for new design. 3/ Inactive for

35、new design, use dash number -021 for new design. 4/ Inactive for new design, use dash number -009 for new design. 10MIL-DTL-15370/10EProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15370/10E 11 REQUIREMENTS: Design, construction, and physical

36、 dimensions: See figures 1 through 6 and table I. Operating temperature range: -54C to +85C for dash numbers 022 through 028. -55C to +100C for dash numbers 014 and 020. -54C to +110C for dash numbers 001 through 013, 015 through 019, 021, 023 through 027, 029, and 030. Weight: See table I. Electric

37、al: See table II. Marking: Part number (see tables I and II) shall be located as shown on figures 1 through 6. Part number: M15370/10- (and a dash number from table I). Referenced Documents: In addition to MIL-DTL-15370, this document references the following: MIL-PRF-39012/55 The margins of this sp

38、ecification are marked with vertical lines to indicate where modifications from this revision were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements

39、of this document based on the entire content irrespective of the marginal notations. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC (Project 5985-2012-035) Air Force - 85 DLA - CC Review activities: Navy - AS, CG, MC, OS, SH Air Force - 99 NOTE: The activities listed above were interes

40、ted in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-