DLA DSCC-DWG-87073 REV D-2007 RESISTOR NETWORK FIXED FILM EIGHT PIN SIP MULTIPLE RESISTANCE VALUES MULTIPLE SCHEMATICS (LOW PROFILE)《电阻网络 固定性 胶片 8-PIN SIP 多层电阻阻值 复合图表(薄层)》.pdf
《DLA DSCC-DWG-87073 REV D-2007 RESISTOR NETWORK FIXED FILM EIGHT PIN SIP MULTIPLE RESISTANCE VALUES MULTIPLE SCHEMATICS (LOW PROFILE)《电阻网络 固定性 胶片 8-PIN SIP 多层电阻阻值 复合图表(薄层)》.pdf》由会员分享,可在线阅读,更多相关《DLA DSCC-DWG-87073 REV D-2007 RESISTOR NETWORK FIXED FILM EIGHT PIN SIP MULTIPLE RESISTANCE VALUES MULTIPLE SCHEMATICS (LOW PROFILE)《电阻网络 固定性 胶片 8-PIN SIP 多层电阻阻值 复合图表(薄层)》.pdf(16页珍藏版)》请在麦多课文档分享上搜索。
1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add new source of supply; change temperature coefficient of schematic 08. Editorial changes throughout. 29 May 92 D. MOORE B Changes in accordance with NOR 5905-R013-93. 28 May 93 D. MOORE C Update and validation of drawing. Editorial changes throughout. 11
2、 Sep 00 K. COTTONGIM D Add pure tin prohibition paragraph. Editorial changes throughout. 2 Feb 07 M. RADECKI CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 Selected item drawing REV S
3、TATUS OF PAGES REV D D D D D D D D D D D D D D D D PAGES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PMIC N/A PREPARED BY Alan R. Knox DESIGN ACTIVITY: DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO 45444-5000 Original date of drawing: 11 November 1987 CHECKED BY David W. Withrow TITLE RESISTOR NETWORK, F
4、IXED, FILM, 8-PIN SIP, MULTIPLE RESISTANCE VALUES, MULTIPLE APPROVED BY David E. Moore SCHEMATICS, (LOW PROFILE) SIZE A CODE IDENT. NO. 14933 DWG NO. 87073 REV D PAGE 1 OF 16 AMSC N/A 5905-E626 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE
5、ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87073 REV D PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for an 8-pin, low profile, single-in-line package (SIP), fixed, film, resistor network. 1.2 Part or Identifying Number (PIN). The complete PIN is a
6、s follows: 87073 - 01 Drawing number Schematic number (see figure 2) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise
7、specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-83401 - Resistor Networks, Fixed, Film, and Capacitor-Resistor Networks, Ceramic Capacitor and Fixed Film Resistors, General Specification for. DEPARTMENT OF DEFENSE
8、 STANDARDS MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
9、 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, (except for related associated detail specifications, specification sheets, or MS standards), the text of this document takes precedence. Nothing in this document, however, superse
10、des applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item Requirements. The individual item requirements shall be in accordance with MIL-PRF-83401 and as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface a
11、nd physical dimensions as specified in MIL-PRF-83401 and herein (see figure 1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87073 REV D PAGE 3 Inches mm Inches mm I
12、nches mm 0.002 0.05 0.019 0.48 0.125 3.17 0.005 0.006 0.12 0.15 0.098 0.100 2.48 2.54 0.200 0.800 5.08 20.32 0.010 0.25 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, dimensional tolerances shall be 0.02 (0.5 mm) for t
13、wo decimal places and 0.010 (0.25 mm) for three decimal places. 4. The picturization of the styles above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope and do not alter the functional aspects of the device, ar
14、e acceptable. FIGURE 1. Resistor network. 3.3 Electrical characteristics. 3.3.1 Resistance. The resistance value shall be as specified on figure 2. 3.3.2 Resistance tolerance. The resistance tolerance shall as specified on figure 2. 3.3.3 Resistor power rating. The resistor power rating for individu
15、al resistors shall be 125 milliwatts maximum at 70oC derated to 0 watts at 150oC. 3.3.4 Package power rating. The package power rating shall not exceed the sum of the individual resistance element power rating in the network. 3.3.5 Operating voltage. Each resistor element shall have a maximum operat
16、ing voltage of 100 V dc or ac rms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87073 REV D PAGE 4 3.3.6 Schematic. Resistor networks are available in schematics lis
17、ted on figure 2. 3.3.7 Resistance temperature characteristic. Unless otherwise specified, the resistance temperature characteristic shall be 100 ppm/oC. 3.4 Characteristic. The characteristic shall be in accordance with MIL-PRF-83401, characteristic K. 3.5 Pure tin. The use of pure tin, as an underp
18、late or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.4). 3.6 Environmental requirements. The environmental requirements shall be in
19、accordance with MIL-PRF-83401, characteristic K. 3.7 Marking. Marking shall be in accordance with MIL-STD-1285, except the PIN shall be as specified in 1.2, with the manufacturers CAGE number or trade mark and date code. 3.8 Recycled, recovered, or environmentally preferable materials. Recycled, rec
20、overed, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.9 Certificate of compliance. A certificate of compliance
21、shall be required from manufacturers requesting to be listed as a suggested source of supply. 3.10 Workmanship. Resistors shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection
22、 is not applicable to this document. 4.2 Conformance inspections. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A and group B inspections of MIL-PRF-83401. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate o
23、f compliance with group B requirements in lieu of performing group B tests (see 6.2d). 4.3 Inspection of packaging. Inspection of packaging shall be in accordance with MIL-PRF-83401. 4.4 Visual and mechanical examination. Resistors shall be examined to verify that the materials, design, construction
24、, physical dimensions, marking, and workmanship are in accordance with the applicable requirements of MIL-PRF-83401. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performe
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLADSCCDWG87073REVD2007RESISTORNETWORKFIXEDFILMEIGHTPINSIPMULTIPLERESISTANCEVALUESMULTIPLESCHEMATICSLOWPROFILE

链接地址:http://www.mydoc123.com/p-688865.html