DLA DSCC-DWG-87068 REV D-2007 RESISTOR NETWORK FIXED FILM 7-PIN SIP (HIGH PROFILE) MULITPLE SCHEMATICS《电阻网络 固定性 胶片 7-PIN SIP(厚层) 复合图表》.pdf

《DLA DSCC-DWG-87068 REV D-2007 RESISTOR NETWORK FIXED FILM 7-PIN SIP (HIGH PROFILE) MULITPLE SCHEMATICS《电阻网络 固定性 胶片 7-PIN SIP(厚层) 复合图表》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-87068 REV D-2007 RESISTOR NETWORK FIXED FILM 7-PIN SIP (HIGH PROFILE) MULITPLE SCHEMATICS《电阻网络 固定性 胶片 7-PIN SIP(厚层) 复合图表》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add new vendor. 20 May 88 D. MOORE B Changes in accordance with NOR 5905-R011-93. 28 May 93 D. MOORE C Update and validation of drawing. Editorial changes throughout. 11 Sep 00 K. COTTONGIM D Add pure tin prohibition paragraph. Editorial changes throughout.

2、 31 Jan 07 M. RADECKI CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 Selected item drawing REV STATUS OF PAGES REV D D D D D D D D PAGES 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Alan R. K

3、nox DESIGN ACTIVITY: DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO 45444-5000 Original date of drawing: CHECKED BY David W. Withrow TITLE RESISTOR NETWORK, FIXED, FILM, 7-PIN SIP 29 December 1987 APPROVED BY David E. Moore (HIGH PROFILE), MULTIPLE SCHEMATICS SIZE A CODE IDENT. NO. 14933 DWG NO. 8706

4、8 REV D PAGE 1 OF 8 AMSC N/A 5905-E623 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87068 REV D PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements fo

5、r a 7-pin, low profile, single-in-line package (SIP), fixed film, resistor network. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 87068 - 01 Drawing number Schematic number (see figure 2) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and h

6、andbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-83401 - Resistor Netwo

7、rks, Fixed, Film, and Capacitor-Resistor Networks, Ceramic Capacitor and Fixed Film Resistors, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearc

8、h/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, (except for related associated detail

9、 specifications, specification sheets, or MS standards), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item Requirements. The individual item requirements sh

10、all be in accordance with MIL-PRF-83401 and as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions as specified in MIL-PRF-83401 and herein (see figure 1). 3.3 Electrical characteristics. 3.3.1 Resistance. The resistance value shall

11、be as specified on figure 2. 3.3.2 Resistance tolerance. The resistance tolerance shall as specified on figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87068

12、REV D PAGE 3 Inches mm Inches mm Inches mm Inches mm 0.002 0.05 0.010 0.25 0.100 2.54 0.320 8.12 0.005 0.12 0.019 0.48 0.125 3.17 0.700 17.78 0.006 0.15 0.098 2.48 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, dimensi

13、onal tolerances shall be 0.02 (0.5 mm) for two decimal places and 0.010 (0.25 mm) for three decimal places. 4. The picturization of the styles above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope and do not al

14、ter the functional aspects of the device, are acceptable. FIGURE 1. Resistor network. 3.3.3 Resistor power rating. The resistor power rating for individual resistors shall be 125 milliwatts maximum at 70oC derated to 0 watts at 150oC. 3.3.4 Package power rating. The package power rating shall not ex

15、ceed the sum of the individual resistance element power rating in the network. 3.3.5 Operating voltage. Each resistor element shall have a maximum operating voltage of 100 V dc or ac rms. 3.3.6 Schematic. Resistor networks are available in schematics listed on figure 2. 3.3.7 Resistance temperature

16、characteristic. Unless otherwise specified, the resistance temperature characteristic shall be 100 ppm/oC. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87068 REV D P

17、AGE 4 3.4 Characteristic. The characteristic shall be in accordance with MIL-PRF-83401, characteristic K. 3.5 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by ma

18、ss. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.4). 3.6 Environmental requirements. The environmental requirements shall be in accordance with MIL-PRF-83401, characteristic K. 3.7 Marking. Marking shall be in accordance with MIL-STD-1285, except the PIN shall be as specifie

19、d in 1.2, with the manufacturers CAGE number or trade mark and date code. 3.8 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the opera

20、tional and maintenance requirements, and promotes economically advantageous life cycle costs. 3.9 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be listed as a suggested source of supply. 3.10 Workmanship. Resistors shall be uniform in quali

21、ty and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not applicable to this document. 4.2 Conformance inspections. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shal

22、l consist of group A and group B inspections of MIL-PRF-83401. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). 4.3 Inspection of packaging. Inspection of packaging shall b

23、e in accordance with MIL-PRF-83401. 4.4 Visual and mechanical examination. Resistors shall be examined to verify that the materials, design, construction, physical dimensions, marking, and workmanship are in accordance with the applicable requirements of MIL-PRF-83401. 5. PACKAGING 5.1 Packaging. Fo

24、r acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements.

25、Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packagi

26、ng files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87068 REV D PAGE 5 NOTES: 1. Resistor po

27、wer rating shall be capable of withstanding at least 25 mW at 120oC. 2. k = kilohms. 3. Resistance tolerance shall be 1 percent. . NOTES: 1. Resistor power rating shall be capable of withstanding at least 25 mW at 120oC. 2. k = kilohms. 3. Resistance tolerance shall be 1 percent. FIGURE 2. Schematic

28、, resistance and tolerance.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87068 REV D PAGE 6 NOTES: 1. Resistor temperature coefficient: 200 ppm/oC maximum. 2. k = kil

29、ohms. 3. Resistance tolerance for shall be 3 percent. NOTES: 1. Resistor power rating shall be capable of withstanding at least 25 mW at 120oC. 2. k = kilohms. 3. Resistance tolerance shall be 1 percent. FIGURE 2. Schematic, resistance and tolerance - Continued.Provided by IHSNot for ResaleNo reprod

30、uction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87068 REV D PAGE 7 NOTES: 1. Resistor power rating shall be capable of withstanding at least 25 mW at 120oC. 2. k = kilohms. 3. Resistance tolerance shall be

31、1 percent. FIGURE 2. Schematic, resistance and tolerance - Continued. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Resistor networks are used in surface mounting applications where space is a major concer

32、n. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery, and one copy of the conformance inspection data or certification of compliance that parts have passed conformance inspection with each shipment of parts by the

33、manufacturer. c. Requirements for packaging and packing. (i.e. ESD sensitive packaging). d. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements. 6.3 Electrostatic charge. Under several combinations of conditions, these resistors can b

34、e electrically damaged, by electrostatic charges, and drift from specified value. Users should consider this phenomena when ordering or shipping resistors. Direct shipment to the Government is controlled by MIL-DTL-39032 which specifies a preventive packaging procedure. Provided by IHSNot for Resale

35、No reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87068 REV D PAGE 8 6.4 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth proble

36、ms after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of

37、 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.5 User of record. Coordination of this document for future revisions is coordinated only with the

38、 suggested source of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at resistordla.mil or in writing to: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. 6.6 Sugges

39、ted source of supply. Suggested source of supply is listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at resistordla.mil or contact DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0

40、552 or DSN 850-0552. DSCC drawing PIN Vendor similar designation or type number 1/ Vendor CAGE Vendors name and address 87068-* 7SM-*-FX 17826 Vishay Techno 4051 Greystone Drive Ontario, CA 91761 MSP07 91637 Vishay - Dale P.O. Box 609 Columbus, NE 68601-0609 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-