DLA DSCC-DWG-87067 REV D-2007 RESISTOR NETWORK FIXED FILM 7-PIN SIP (LOW PROFILE) MULTIPLE SCHEMATICS《电阻网络 固定性 胶片 7-PIN SIP(薄层) 复合图表》.pdf

《DLA DSCC-DWG-87067 REV D-2007 RESISTOR NETWORK FIXED FILM 7-PIN SIP (LOW PROFILE) MULTIPLE SCHEMATICS《电阻网络 固定性 胶片 7-PIN SIP(薄层) 复合图表》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-87067 REV D-2007 RESISTOR NETWORK FIXED FILM 7-PIN SIP (LOW PROFILE) MULTIPLE SCHEMATICS《电阻网络 固定性 胶片 7-PIN SIP(薄层) 复合图表》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add new schematics. Add new vendor. Editorial changes throughout. 8 Aug 88 D. MOORE B Changes in accordance with NOR 5905-R015-93. 31 Oct 93 A. BOULTER C Update and validation of drawing. Editorial changes throughout. 11 Sep 00 K. COTTONGIM D Add pure tin p

2、rohibition paragraph. Editorial changes throughout. 31 Jan 07 M. RADECKI CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 Selected item drawing REV D D D D D D D D D D D REV STATUS OF P

3、AGES PAGES 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Alan R. Knox DESIGN ACTIVITY: DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO 45444-5000 CHECKED BY David W. Withrow APPROVED BY David E. Moore TITLE RESISTOR NETWORK, FIXED, FILM, 7-PIN SIP (LOW PROFILE), MULTIPLE SCHEMATICS SIZE A CODE IDENT. N

4、O. 14933 DWG NO. 87067 Original date of drawing: 29 December 1987 REV D PAGE 1 OF 11 AMSC N/A 5905-E622 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87067 REV D PAGE

5、 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a 7-pin, low profile, single-in-line package (SIP), fixed, film, resistor network. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 87067 - 01 Drawing number Schematic number (see figure 2) 2. APPLICABLE DOCUMENT

6、S 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. D

7、EPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-83401 - Resistor Networks, Fixed, Film, and Capacitor-Resistor Networks, Ceramic Capacitor and Fixed Film Resistors, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these docu

8、ments are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and

9、the references cited herein, (except for related associated detail specifications, specification sheets, or MS standards), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUI

10、REMENTS 3.1 Item Requirements. The individual item requirements shall be in accordance with MIL-PRF-83401 and as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions as specified in MIL-PRF-83401 and herein (see figure 1). 3.3 Electri

11、cal characteristics. 3.3.1 Resistance. The resistance value shall be as specified on figure 2. 3.3.2 Resistance tolerance. The resistance tolerance shall as specified on figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUP

12、PLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87067 REV D PAGE 3 Inches mm Inches mm Inches mm 0.006 0.15 0.100 2.54 0.200 5.08 0.019 0.48 0.125 3.17 0.700 17.78 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specif

13、ied, dimensional tolerance shall be 0.02 (0.5 mm) for two decimal places and 0.010 (0.25 mm) for three decimal places. 4. The picturization of the styles above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope an

14、d do not alter the functional aspects of the device, are acceptable. FIGURE 1. Resistor network. 3.3.3 Resistor power rating. The resistor power rating for individual resistors shall be 125 milliwatts maximum at 70oC derated to 0 watts at 150oC. 3.3.4 Package power rating. The package power rating s

15、hall not exceed the sum of the individual resistance element power rating in the network. 3.3.5 Operating voltage. Each resistor element shall have a maximum operating voltage of 100 V dc or ac rms. 3.3.6 Schematic. Resistor networks are available in schematics listed on figure 2. 3.3.7 Resistance t

16、emperature characteristic. Unless otherwise specified, the resistance temperature characteristic shall be 100 ppm/oC. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87

17、067 REV D PAGE 4 3.4 Characteristic. The characteristic shall be in accordance with MIL-PRF-83401, characteristic K. 3.5 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 per

18、cent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.4). 3.6 Environmental requirements. The environmental requirements shall be in accordance with MIL-PRF-83401, characteristic K. 3.7 Marking. Marking shall be in accordance with MIL-STD-1285, except the PIN shall be

19、as specified in 1.2, with the manufacturers CAGE number or trade mark and date code. 3.8 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceed

20、s the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.9 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be listed as a suggested source of supply. 3.10 Workmanship. Resistors shall be unifo

21、rm in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not applicable to this document. 4.2 Conformance inspections. 4.2.1 Inspection of product for delivery. Inspection of product for de

22、livery shall consist of group A and group B inspections of MIL-PRF-83401. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). 4.3 Inspection of packaging. Inspection of packag

23、ing shall be in accordance with MIL-PRF-83401. 4.4 Visual and mechanical examination. Resistors shall be examined to verify that the materials, design, construction, physical dimensions, marking, and workmanship are in accordance with the applicable requirements of MIL-PRF-83401. 5. PACKAGING 5.1 Pa

24、ckaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging req

25、uirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automa

26、ted packaging files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87067 REV D PAGE 5 NOTES: 1.

27、Resistors R2, R3, and R6: Shall be within tolerance over the temperature range. 2. Resistors R1 and R4 tracking coefficient: 50 ppm/oC maximum. 3. M = megohms; k = kilohms. 4. Resistance tolerance for R1, R4, and R5 shall be 2 percent. R3, and R6, and R2 resistance tolerance shall be 20 percent. NOT

28、ES: 1. k = kilohms. 2. Resistance tolerance for R2, R3, R4, and R5 shall be 2 percent. R1 shall be 20 percent. FIGURE 2. Schematic, resistance and tolerance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHI

29、O SIZE A CODE IDENT NO. 14933 DWG NO. 87067 REV D PAGE 6 NOTES: 1. Resistor temperature coefficient: 200 ppm/oC maximum. 2. Power rating shall be 60mW at 120oC. The power rating for R2, R3, and R5 shall be 25 mW at 120oC. 3. k = kilohms. 4. Resistance tolerance shall be 3 percent. NOTES: 1. Resistor

30、 temperature coefficient: 200 ppm/oC maximum. 2. R4 power rating shall be 50mW at 120oC. The power rating for R1, R2, R3, and R5 shall be 25 mW at 120oC. 3. k = kilohms. 4. Resistance tolerance shall be 3 percent. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for Resa

31、leNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87067 REV D PAGE 7 NOTES: 1. Resistor temperature coefficient: 200 ppm/oC maximum. 2. Power rating for R2 and R3 shall be 30 mW at 120oC. The power

32、 rating for R1 and R4 shall be 25 mW at 120oC. 3. k = kilohms. 4. Resistance tolerance shall be 3 percent. NOTES: 1. Resistor power rating shall be capable of withstanding at least 25 mW at 120oC. 2. k = kilohms. 3. Resistance tolerance for shall be 2 percent. FIGURE 2. Schematic, resistance and tol

33、erance - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87067 REV D PAGE 8 NOTES: 1. Resistor power rating shall be capable of withstanding at least 25 mW a

34、t 120oC. 2. k = kilohms. 3. Resistance tolerance shall be 1 percent. NOTES: 1. Resistor temperature coefficient: 200 ppm/oC maximum. 2. k = kilohms. 3. Resistance tolerance for shall be 3 percent. FIGURE 2. Schematic, resistance and tolerance - Continued.Provided by IHSNot for ResaleNo reproduction

35、or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87067 REV D PAGE 9 NOTES: 1. Resistor power rating shall be capable of withstanding at least 25 mW at 120oC. 2. k = kilohms. 3. Resistance tolerance shall be 1 perce

36、nt. NOTES: 1. Resistor temperature coefficient: 200 ppm/oC maximum. 2. Power rating for R4 shall be 50 mW at 120oC. The power rating for R1, R2, R3 and R5 shall be 25 mW at 120oC. 3. k = kilohms; = ohms. 4. Resistance tolerance shall be 3 percent. FIGURE 2. Schematic, resistance and tolerance - Cont

37、inued.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87067 REV D PAGE 10 NOTES: 1. Resistor temperature coefficient: 200 ppm/oC maximum. 2. Power rating for R4 shall b

38、e 50 mW at 120oC. The power rating for R1, R2, R3 and R5 shall be 25 mW at 120oC. 3. k = kilohms; = ohms. 4. Resistance tolerance shall be 3 percent. FIGURE 2. Schematic, resistance and tolerance - Continued. 6. NOTES (This section contains information of a general or explanatory nature that may be

39、helpful, but is not mandatory.) 6.1 Intended use. Resistor networks are used in surface mounting applications where space is a major concern. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery, and one copy of the c

40、onformance inspection data or certification of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. (i.e. ESD sensitive packaging). d. Whether the manufacturer performs the group B tests or provides certi

41、fication of compliance with group B requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87067 REV D PAGE 11 6.3 Electrostatic charge. Under several combinatio

42、ns of conditions, these resistors can be electrically damaged, by electrostatic charges, and drift from specified value. Users should consider this phenomena when ordering or shipping resistors. Direct shipment to the Government is controlled by MIL-DTL-39032 which specifies a preventive packaging p

43、rocedure. 6.4 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that

44、use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specificatio

45、n for Electrodeposited Coatings of Tin). 6.5 User of record. Coordination of this document for future revisions is coordinated only with the suggested source of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at resistor

46、dla.mil or in writing to: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. 6.6 Suggested source of supply. Suggested source of supply is listed herein. Additional sources will be added as they become available. Assistance in the use of this draw

47、ing may be obtained online at resistordla.mil or contact DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DSCC drawing PIN Vendor similar designation or type number 1/ Vendor CAGE Vendors name and address 87067-* All schematics 7SM-*-FX 17826 Vi

48、shay Techno 4051 Greystone Drive Ontario, CA 91761 87067-* Schematics 02 through 11 MSP07 91637 Vishay - Dale P.O. Box 609 Columbus, NE 68601-0609 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-