DLA AN107501 THRU AN107600 REV 3-1986 BOLT-CRES DRILLED HEX HEAD 6 HOLES 3125-24《螺栓 耐蚀钢钻孔六角头 6孔 3125-24》.pdf

《DLA AN107501 THRU AN107600 REV 3-1986 BOLT-CRES DRILLED HEX HEAD 6 HOLES 3125-24《螺栓 耐蚀钢钻孔六角头 6孔 3125-24》.pdf》由会员分享，可在线阅读，更多相关《DLA AN107501 THRU AN107600 REV 3-1986 BOLT-CRES DRILLED HEX HEAD 6 HOLES 3125-24《螺栓 耐蚀钢钻孔六角头 6孔 3125-24》.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、- _ . I-_ AN30750L THRU AN307600 REV 3 53 7777735 0000285 4 d I .O95 TO POINT ,016 OR CIIAMFE SECTION THRU THREAI PROFILE .IO0 DIA 6 HOLES SPACED AS SHOWN WITHIN .O20 OF TRUE POSITION LTHIS SURFACE MUST BE SQUARE WITH SHANK WITHIN .O03 FULL INDICATOR CSINK 90 TO READING CHAMFER 30 TO .SOO DIA (OPPOS

2、ITE SIDE OPTIONAL) - L - .500 .562 .625 -750 .812 .a75 .938 1.000 1.062 L. 188 .688 1.125 1.250 1.312 PART NO. +. O00 AN107506 AN107507 AN107506 .188 .250 .312 AN107509 AN107510 AN107511 AN107512 AN107513 AN107514 AN107515 AN107516 AN107517 .375 AN107518 .438 AN107519 I L - 1.375 1.438 1.500 1.562 1

3、.625 1.688 1.750 1.812 1.875 2.000 2.250 2 375 2.500 2.125 K PART NO +. O00 - .o60 .562 107521 ,625 107522 .688 107523 .500 AN107520 AN107524 :i?: AN107525 .875 AN107526 .938 AN10752 1.000 ANlO752i 1.125 AN107529 1.250 AN107530 1.375 AN107531 1.500 AN107532 1.625 AN107533 L 2.625 2.750 2.5 3.000 3.1

4、25 3.250 3.375 3.500 3.625 4.125 4.250 +.o00 1.750 AN107534 1.875 AN107535 2.000 AN107536 2.125 AN107537 2.375 AN107539 2.250 107538 2.500 AN107540 2.750 AN107542 2.625 AN107541 2.875 AN107543 3.005 AN107544 3.125 AN107545 3.250 107546 3.375 AN107547 I L K PART NO. +.o00 - .O60 4.325 3.500 AN10754f

5、4.500 3.625 AN10754! 4.625 3.750 AN10755C 4.750 3.875 AN10755: 5.000 4.125 AN107552 5.125 4.250 AN107554 5.250 4.375 AN10755 5.375 4.500 AN10755t 5.500 4.625 AN10755 5.625 4. 50 AN10755Z 5.750 4.835 AN107555 5.875 5.000 ANlW56C 4. 675 4.000 AN10755: 6.000 5.125 mi07561 (a) THREAkTO HEAD. UAXIMUU TU0

6、 IMPERFECT THREADS. NOTE: (I) SHANK SHALL .BE STRAIGHT UITHIN .O03 FIR. PER INCH OF BOLT LENGTH. (2): THE CONCEITRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIE. (3): THE CONCENTRICITY OF THE SHANK IN RELATIOK TO THE YASHER FACE DIAUETEE AND HEXAGON SHALL BE UITHIN .O15 FIR, IN

7、ACTIVE FOR DESIGN AFTER 27 DEC 1966 NO SUPERSEDING STANDARD. UATERIAL: : CORROSION RESISTANT STEEL - SEE UANUFACTURING SPECIFICATION SURFACE ROUGHNESS: ASID7 HANUFACTURING SPECIFICATION: AUS 7472 ) INSPECTIONs ALL PARTS SHALL UNDERGO FLUORESCENT PENETRANT INSPECTION IN ACCORDANCX YITH AUS2645. BREAK

8、 SHARP EDGES .O03 - .O15 UNLESS OTHERUISE SPECIFIED. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED: TOLERANCES: LINEAE DIUENSIONS i.010. ANGULAR DIUENSIONS 22 DO NOT USE UNASSIGNED PART NUUBERS. THIS STANDARD VAS DEVELOPED COOPERATIVELY YITH THE ENGINE AND PROPELLER UTILITY PARTS COMMITTEE DF THE SAE. P.A. AIR FORCE-NAW AERONAUTICAL STANDARD AN1 07501 Other Cust THRU USAI - 11 Navy - AS BOLT - CRES DRILLED HEX HEAD, 6 HOLES, .312S - 24 ANI07600 Ariy - AV IOTIIDnRIIIOIIIcL In*1.I,Wmll Project No. 5306-105 THIS DOCUMENT CONTAINS i- - PAGES. I - Licensed by Information Handling Services