DLA AN107101 THRU AN107200 REV 3-1986 BOLT-CRES DRILLED HEX HEAD 1 HOLE 625-18《螺栓 耐蚀钢钻孔六角头 1孔 625-18》.pdf

《DLA AN107101 THRU AN107200 REV 3-1986 BOLT-CRES DRILLED HEX HEAD 1 HOLE 625-18《螺栓 耐蚀钢钻孔六角头 1孔 625-18》.pdf》由会员分享，可在线阅读，更多相关《DLA AN107101 THRU AN107200 REV 3-1986 BOLT-CRES DRILLED HEX HEAD 1 HOLE 625-18《螺栓 耐蚀钢钻孔六角头 1孔 625-18》.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、- ANLO7301 THRU AN307200 REV 3 53 9999935 000028L 7 PART NO. AN107131 AN107132 nil107133 AN107135 107137 AN107134 AN107136 AN107138 AN107139 DRILL NO. 50 (.070) CSINK 90. TO 4 DIA BOTH ENDS L K +.o00 -. 060 - 4.875 3.375 5.000 3.500 5.125 3.625 5.375 3.875 5.625 4.125 5.250 3.750 5.500 4.000 4.250 4

2、.375 L = 1.250 1.312 1.375 1.438 1.562 1.688 1.500 1.625 1.750 1.812 1.875 (a) AN107140 AN107141 AN107142 Ah107143 AN107144 K +io00 -, 060 ta“/ til !?i8 .250 -312 * 375 6.000 4.500 PART NO. AN1071U6 AN107107 AN107108 AN107109 AN107111 7110 107112 ANiW.11 AN107112 AN107115 107116 P.A. Other Cust USAF

3、 - 11 Navy - AS Ariy - AV - THIS SURFACE MUST BE SQUARE WITH SHANK WITHIN ,003 FULL INDICATOR READING CHAHFER 30 TO .938 DIA (OPPOSITE SIDE OPTIONAL) AIR FORCE-NAVY AERONAUTICAL STANDARD AN I o7 I 0 I AN I y200 BOLT - CRES DRILLED HEX HEAD, 1 HOLE, ,625.- 18 - L - 1.938 2.000 2.062 2.125 2.188 2.250

4、 2.312 :$y2 2.500 2.625 2 - 750 2.875 3.000 .438 AN10711 .500 AN10711g .562 AN107119 .625 107120 .750 107122 .812 10712 .688 AN107121 .875 AN107123 ,938 AN107125 1.000 AN107126 1.125 AN10712 1.250 AN107128 1.375 AN107129 1.500 AN107130 I L I = 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 G.

5、250 4.500 4.625 4.375 4.750 THREAD -TO HEAD. HAXIHUM TWO IHPERIECT THREADS. - K +. O00 - .o60 1.625 1.750 1 * 875 2.000 2.125 2.250 2.375 2.500 2.625 3; 3.000 3.125 3.250 PART - 1071 1071 AN1071 AN1071 AN1071 1071 1071 AN1071 A11071 A101Wl - NOTE: (I) SHANK SHALL BE-STRAIGET WITH .O02 FIR. PER INCH

6、OF BOLT LENGTH. (2) THE CONCENTRICITY OP THREAD PD IN RELATION TO THE SHANK SHALL BE WITHIN .O06 FIR. (3) THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER PACE DIAHETER AND EEXAGOI SHALL BE WITHIN .O28 FIR. INACTIVE FOR DESIGN AFTER 27DEC 1966 NO SUPERSEDING STANDARD. MATERIAL- CORROSION RES

7、ISTANT STEEL - SEE HANUFACTURING SPECIFICATION SURFACKROUCHNESS: AS107 HANUFACTURZNG SPECIFICATION: AHS 7472 31NSPECTSOK: ALL PARTS SHALL UNDERGO FLUORESCENT INSPECTION IN ACCORDANCE WITH AHSZ645 BREAK SHARP EDGES .O03 - .O15 UNLESS OTHERWISE SPECIFIED. DIHENSIONS IN INCHES. UNLESS OTHERWISE SPECIFI

8、ED: TOLERENCES; LINEAR DIMENSIONS t.O1O, ANGULAR DIMENSIONS 52. DO NOT USEUNASSIGNED PART NUBERS. THIS STANDRD WAS DEVELOPED COOPERATIVELY WITH THE ENGINE AND PROPELLER UTILITY PARTS COHHITTEE OF THE SAl THIS DOCUMENT CONTAINS 1- .- PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-