DLA A-A-59789 19-2009 HOLDER ELECTRICAL CARD WEDGE RETAINERS 5 PIECE FOR COLD PLATE APPLICATIONS 250 X 270 INCH (6 35 x 6 86 mm) BODY SIZE WITH CAPTIVE REAR WEDGE SCREW ACTUATED.pdf

《DLA A-A-59789 19-2009 HOLDER ELECTRICAL CARD WEDGE RETAINERS 5 PIECE FOR COLD PLATE APPLICATIONS 250 X 270 INCH (6 35 x 6 86 mm) BODY SIZE WITH CAPTIVE REAR WEDGE SCREW ACTUATED.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59789 19-2009 HOLDER ELECTRICAL CARD WEDGE RETAINERS 5 PIECE FOR COLD PLATE APPLICATIONS 250 X 270 INCH (6 35 x 6 86 mm) BODY SIZE WITH CAPTIVE REAR WEDGE SCREW ACTUATED.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUND AA59789/19 2 May 2009 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 5 PIECE, FOR COLD PLATE APPLICATIONS, .250 X .270 INCH (6.35 x 6.86 mm) BODY SIZE, WITH CAPTIVE REAR WEDGE, SCREW ACTUATED The General Services Administration has authorized the

2、 use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59789. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item descript

3、ion (CID) specification sheet uses a classification system which is included in the PIN as shown in the following example (see NOTES). AA59789 CID number /19 Applicable CID sheet * Configuration (see table I) * Finish (see table I) * * Length (see table II) * Mounting (see table I) Example: AA59789/

4、19DH30S is the PIN for a hard black anodized finished, 2.8 inch (71.1 mm) long card holder. The card holder also features three tapped mounting holes for use with 256 UNF 2B fasteners and a screw self-locking element for added resistance to loosening. SALIENT CHARACTERISTICS. Performance. Card holde

5、rs shall hold the circuit card firmly in place providing high resistance to shock and vibration while providing maximum thermal transfer. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified herein and meet the general requirements specif

6、ied in CID AA59789. Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA59789. Actuating screw hex drive socket. The dimension for hex drive socket shall be .094 inch (2.38 mm) across flats for mounting options “M“, “R“, “S“, “T“, and “U“. Cold plate slo

7、t width. The recommended cold plate slot width to accommodate the circuit card assembly with attached card holder is .300 inch (7.62 mm) plus the thickness of the printed board of the circuit card assembly (see AA59789). Installation torque. The recommended nominal installation torque is follows: 6

8、inch-pounds (0.7 N-m) for card holders of configuration “C“ or “E“ and 7 to 8 inch-pounds (0.8 to 0.9 N-m) for assemblies of configurations “L“ or “D“. Configuration. The configuration of a card holder shall be as specified in table I. The details of a particular configuration consist of those on fi

9、gure 1, and may include those on figures 2 and 3. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/19 2table I tables I TABLE I. Configurations. Configuration Applicable figures Hardware options C 1 No added options L 1 and 2

10、 Screw self-locking element E 1 and 3 Additional mounting hole D 1, 2, and 3 Screw self-locking element and additional mounting hole figure 1 figures 1 1 Inches mm Inches mm Inches mm Inches mm .250 6.35 .270 6.86 .325 8.26 .80 20.32 NOTES: 1. Dimensions are in inches. Millimeter equivalents are giv

11、en for information only. 2. Unless otherwise specified, tolerances are for .02 inch (0.51 mm) for two place decimals and .010 (0.25 mm) for three place decimals. 3. Tolerance for the hole spacing is .005 inch (0.13 mm). 4. The across flats dimension for hex drive socket shall be .094 inch (2.38 mm).

12、 FIGURE 1. Relaxed and expanded dimensions. Finish. The finish designator shall be as specified in AA59789. The finishes available for this CID specification sheet are as follows: “B“ (black anodize), “C“ (chemical film), “E“ (electroless nickel), or “H“ (hard black anodize). Length, expanded, and r

13、elaxed dimensions. The length designator shall be as specified in AA59789 and the lengths available for this CID specification sheet are listed in table II. The length, expanded, and relaxed dimensions shall be as specified on figure 1. Provided by IHSNot for ResaleNo reproduction or networking perm

14、itted without license from IHS-,-,-AA59789/19 3table II TABLE II. Additional assembly dimensions (see figure 1). 1/ PIN length designator Dimension “length“ .02 (0.5) Dimension “M“ .005 (0.13) Dimension “M/2“ .005 (0.13) 30 2.80 (71.1) .90 (22.9) .45 (11.4) 40 3.80 (96.5) 1.90 (48.3) .95 (24.1) 50 4

15、.80 (121.9) 2.90 (73.7) 1.45 (36.8) 1/ Dimensions are in inches. Millimeters, in parenthesis, are given for information only. Mounting. The mounting designators shall be as specified in AA59789. The mounting options available for this CID specification sheet are as follows: “M“ (tapped metric M2.5 x

16、 0.45 holes), “R“ (rivet mount holes with counterbore and countersink), “S“ (tapped 2-56 holes), “T“ (tapped 0-80 holes), or “U“ (tapped metric M2 x 0.4 holes). See figure 1 for mounting hole spacing requirements. Rivet mounting holes. The holes used for rivet mounting shall be .068/.073 inch (1.73/

17、1.85 mm) diameter, countersunk 100 degrees by .060 inch (1.52 mm) deep. Rivets. This card holder uses rivet type A as specified in AA59789 when rivet mounting is used. Configuration hardware options. Card holders can have the following options. See table I for the correct PIN configuration identifie

18、r. Screw self-locking element (see figure 2). The use of a screw self-locking element will provide prevailing torque for resistance to loosening from shock vibration. Card holders requiring a screw self-locking element shall include configuration identifier “L“ in the PIN (see table I). FIGURE 2. Sc

19、rew self-locking element details. Additional mounting hole (see figure 3). Card holders requiring an additional mounting hole shall include configuration identifier “E“ in the PIN (see table I). FIGURE 3. Additional mounting hole details. Screw self-locking element and additional mounting hole. Card

20、 holders requiring a screw self-locking element and an additional mounting hole options shall include configuration identifier “D“ in the PIN (see table I). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/19 4NOTES. PIN. The PIN should be use

21、d for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description AA59789 Holder, Electrical Card, Wedge Retainers, 5 Piece, For Cold Plate Applications, General Requirements F

22、or. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Other Publications AEROSPACE INDUSTRIES ASSOCIATION (AIA) AIA/NAS

23、 1283 Fasteners, Male Threaded, Selflocking. (Application for copies should be addressed to the Aerospace Industries Association, 1250 Eye Street, NW, Suite 1200, Washington, DC 200053924 or at URL: http:/www.aia-aerospace.org.) Ordering data. Ordering data is as specified in AA59789. Commercial pro

24、ducts. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would

25、meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 5BG68 Card

26、 Locks Unlimited, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: Part number supersession data. These CID specification sheet PINs supersedes the following manufacturers part numbers as shown in table III and on DESC Drawing 89

27、024 (table IV) as shown. The CID PINs listed in table III are only for length designator “50“. See table V for CID PIN construction using other available lengths for this CID specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory syste

28、m. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/19 5Table III table III III TABLE III. Commercial part number supersession data. PIN designator AA59789/19 Vendor similar designator or type part number 1/ CAGE 5BG68 PIN designator AA59789/1

29、9 Vendor similar designator or type part number 1/ CAGE 5BG68 CB50M 5260BA-4.80TM2.5 EB50M 5260BA-4.80ETM2.5 CB50R 5260BA-4.80H EB50R S260VBA-4.80EH CB50S 5260BA-4.80T2 EB50S 5260BA-4.80ET2 CB50T 5260BA-4.80T0 EB50T 5260BA-4.80ET0CB50U 5260BA-4.80TM2 EB50U 5260BA-4.80ETM2 LB50M 5260BA-4.80TM2.5L DB5

30、0M 5260BA-4.80ETM2.5L LB50R 5260BA-4.80HL DB50R 5260BA-4.80EHL LB50S 5260BA-4.80T2L DB50S 5260BA-4.80ET2L LB50T 5260BA-4.80T0L DB50T 5260BA-4.80ET0L LB50U 5260BA-4.80TM2L DB50U 5260BA-4.80ETM2L CC50M 5260CG-4.80TM2.5 EC50M 5260CG-4.80ETM2.5 CC50R 5260CG-4.80H EC50R 5260CG-4.80EH CC50S 5260CG-4.80T2

31、EC50S 5260CG-4.80ET2 CC50T 5260CG-4.80T0 EC50T 5260CG-4.80ET0CC50U 5260CG-4.80TM2 EC50U 5260CG-4.80ETM2 LC50M 5260CG-4.80TM2.5L DC50M 5260CG-4.80ETM2.5L LC50R 5260CG-4.80HL DC50R 5260CG-4.80EHL LC50S 5260CG-4.80T2L DC50S 5260CG-4.80ET2L LC50T 5260CG-4.80TOL DC50T 5260CG-4.80ETOL LC50U 5260CG-4.80TM2

32、L DC50U 5260CG-4.80ETM2L CE50M 5260EN-4.80TM2.5 EE50M 5260EN-4.80ETM2.5 CE50R 5260EN-4.80H EE50R 5260EN-4.80EH CE50S 5260EN-4.80T2 EE50S 5260EN-4.80ET2 CE50T 5260EN-4.80T0 EE50T 5260EN-4.80ET0CE50U 5260EN-4.80TM2 EE50U 5260EN-4.80ETM2 LE50M 5260EN-4.80TM2.5L DE50M 5260EN-4.80ETM2.5L LE50R 5260EN-4.8

33、0HL DE50R 5260EN-4.80EHL LE50S 5260EN-4.80T2L DE50S 5260EN-4.80ET2L LE50T 5260EN-4.80T0L DE50T 5260EN-4.80ET0L LE50U 5260EN-4.80TM2L DE50U 5260EN-4.80ETM2L See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59789/19 6TABL

34、E III. Commercial part number supersession data Continued. PIN designator AA59789/19 Vendor similar designator or type part number 1/ CAGE 5BG68 PIN designator AA59789/19 Vendor similar designator or type part number 1/ CAGE 5BG68 CH50M 5260BH-4.80TM2.5 EH50M 5260BH-4.80ETM2.5 CH50R 5260BH-4.80H EH5

35、0R 5260BH-4.80EH CH50S 5260BH-4.80T2 EH50S 5260BH-4.80ET2 CH50T 5260BH-4.80T0 EH50T 5260BH-4.80ET0CH50U 5260BH-4.80TM2 EH50U 5260BH-4.80ETM2 LH50M 5260BH-4.80TM2.5L DH50M 5260BH-4.80ETM2.5L LH50R 5260BH-4.80HL DH50R 5260BH-4.80EHL LH50S 5260BH-4.80T2L DH50S 5260BH-4.80ET2L LH50T 5260BH-4.80T0L DH50T

36、 5260BH-4.80ET0L LH50U 5260BH-4.80TM2L DH50U 5260BH-4.80ETM2L 1/ The manufacturers part number shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and c

37、ould be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph in AA59789. table IV TABLE IV. DESC Drawing PIN supersession information. Superseded (old) PIN in accordance with DESC Drawing 89024 Superseding (new) CID PIN Superseded (old) PIN in accordance wit

38、h DESC Drawing 89024 Superseding (new) CID PIN 8902401BH AA59789/19CB30R 8902401CH AA59789/19CC30R 8902404BH AA59789/19CB40R 8902404CH AA59789/19CC40R 8902407BH AA59789/19CB50R 8902407CH AA59789/19CC50R 8902401BS AA59789/19CB30T 8902401CS AA59789/19CC30T 8902404BS AA59789/19CB40T 8902404CS AA59789/1

39、9CC40T8902407BS AA59789/19CB50T 8902407CS AA59789/19CC50T 8902401BT AA59789/19CB30S 8902401CT AA59789/19CC30S 8902404BT AA59789/19CB40S 8902404CT AA59789/19CC40S 8902407BT AA59789/19CB50S 8902407CT AA59789/19CC50S Provided by IHSNot for ResaleNo reproduction or networking permitted without license f

40、rom IHS-,-,-AA59789/19 7table V TABLE V. Example of PIN with available length designators. PIN designator AA59789/19 Vendor similar designator or type part number 1/ 2/ CAGE 5BG68 DH30S 5260BH2.80ET2L DH40S 5260BH3.80ET2L DH50S 5260BH4.80ET2L 1/ The manufacturers part number shall not be used for pr

41、ocurement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph in AA59789. 2/ O

42、ther lengths are available on request. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FSS Army CR Navy EC Preparing activity: Air Force 85 DLA CC DLA CC Project 59982008019 Review activity: Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-