CEN TR 15225-2005 Guidance on Factory Production Control for the CE Marking (Attestation of Conformity 2+) of designed masonry mortars《设计圬工灰浆的CE标记(2+一致性的证明)用工厂生产控制指南》.pdf

《CEN TR 15225-2005 Guidance on Factory Production Control for the CE Marking (Attestation of Conformity 2+) of designed masonry mortars《设计圬工灰浆的CE标记(2+一致性的证明)用工厂生产控制指南》.pdf》由会员分享，可在线阅读，更多相关《CEN TR 15225-2005 Guidance on Factory Production Control for the CE Marking (Attestation of Conformity 2+) of designed masonry mortars《设计圬工灰浆的CE标记(2+一致性的证明)用工厂生产控制指南》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、PUBLISHED DOCUMENT PD CEN/TR 15225:2005 Guidance on Factory Production Control for the CE Marking (Attestation of Conformity 2+) of designed masonry mortars ICS 03.120.20; 91.100.10 PD CEN/TR 15225:2005 This Published Document was published under the authority of the Standards Policy and Strategy Co

2、mmittee on 16 December 2005 BSI 16 December 2005 ISBN 0 580 47270 1 National foreword This Published Document is the official English language version of CEN/TR 15225:2005. The UK participation in its preparation was entrusted by Technical Committee B/519, Masonry and associated testing, to Subcommi

3、ttee B/519/2, Mortar, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the

4、BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible fo

5、r its correct application. Compliance with a Published Document does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK inter

6、ests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the CEN/TR title page, pages 2 to 12, an inside back cover and a back cover. The BSI copyright notice displayed in this

7、 document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsTECHNICALREPORT RAPPORTTECHNIQUE TECHNISCHERBERICHT CEN/TR15225 August2005 ICS03.120.20;91.100.10 EnglishVersion GuidanceonFactoryProductionControlfortheCEMarking (AttestationofConformity

8、2+)ofdesignedmasonrymortars Guidedecontrledelaproductionenusinepourle marquageCE(attestationdeconformit2+)desmortiers demaonnerieperformanciels(formuls) AnleitungzurwerkseigenenProduktionskontrollefrdie CEKennzeichnung(Konformittsnachweisverfahren2+) vonMauermrtelnnachEignungsprfung ThisTechnicalRep

9、ortwasapprovedbyCENon12August2005.IthasbeendrawnupbytheTechnicalCommitteeCEN/TC125. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,P

10、ortugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2005CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMember

11、s. Ref.No.CEN/TR15225:2005:ECEN/TR 15225:2005 2 Contents Page Foreword 3 1 Introduction. 4 2 Specifications . 5 3 Inspection schemes . 7 CEN/TR 15225:2005 3 Foreword This Technical Report (CEN/TR 15225:2005) has been prepared by Technical Committee CEN/TC 125 “Masonry“, the secretariat of which is h

12、eld by BSI. 4 1 Introduction This CEN Technical Report has been developed by CEN TC 125 and is aimed at providing guidance regarding factory production control (FPC) for designed masonry mortars (conformity system 2+). For prescribed masonry mortar, plaster and rendering mortar (conformity system 4)

13、 there is no requirement for involvement by Notified Bodies (NBs). Manufacturers of prescribed masonry mortars can use the guidance given in this document as a basis for establishing suitable factory production control procedures to enable demonstration of conformity with the standard and the declar

14、ed values. The aim of this Guidance is to assist manufacturers in their work leading to CE marking of designed mortars. The guidance consists of A general elaboration of Clause 8.3, factory production control, which is common to all the FPC references for the work of Notified Bodies and manufacturer

15、s to be found in Annex ZA, and An inspection scheme containing specific checklists for designed masonry mortar, which is to be considered informative. NOTE This guidance document can be used for the evaluation of factory production control of other types of mortar that are produced in the same facto

16、ry. CEN/TR 15225:20055 2 Specifications 2.1 General These specifications are for the elaboration of FPC according to the instructions in Table ZA.3 in EN 998-2/ Annex ZA, which refer to Clause 8.3 - Factory Production Control. Manufacturers having a factory production control system which complies w

17、ith EN ISO 9001:2000 and which addresses the requirements of the harmonised standard EN 998-2, are recognised as satisfying the FPC requirements of the Directive. The manufacturer shall establish, document and maintain a factory production control system to enable continuing conformity with the stan

18、dard and the declared values of the products placed on the market. The responsibility, authority and interrelation of all personnel who manage, perform and verify work affecting the quality of designed masonry mortar products shall be defined in the documentation of the factory production control sy

19、stem and keep effective. The factory production control system shall describe the procedure of production, the regular inspections by the manufacturer and the testing. Controls and tests should address the characteristics of raw materials and finished products, as well as the production procedures,

20、the production equipment or machines, the test equipment and the marking of the product. All the test results shall be recorded. Actions to be taken when the control test values or criteria do not meet those specified shall be documented by the manufacturer. The conformity of the product shall be de

21、termined by testing according to the requirements of the harmonized standard EN 998-2 and correlated to the values and parameters stated in the factory production control manual. 2.2 Process control 2.2.1 Incoming raw materials As appropriate, the manufacturer shall define the acceptance criteria of

22、 raw materials, and the procedures operated to ensure that these are met. Manufacturers inspection scheme for raw materials is given in Table 1. 2.2.2 Production process The relevant features of the production processes shall be defined giving the frequency of the manufacturers inspection checks, to

23、gether with the required criteria and the required in-progress product characteristics. Actions to be taken when the criteria or the product characteristics are not achieved shall be specified by the manufacturer within the FPC documentation. All production equipment that has an influence on the dec

24、lared values shall be controlled and regularly inspected according to the documented procedures, frequencies and criteria. Manufacturers inspection schemes for production equipment are given in Table 2. CEN/TR 15225:20056 2.3 Finished product conformity 2.3.1 Tests on the finished product The factor

25、y production control system shall incorporate a sampling plan and which shall respect the required frequency of testing of the finished product. The results of testing shall be recorded. The sample shall be representative of the production. The tests shall be carried out in accordance with the metho

26、ds described in the EN 998-2, if given, and with the agreed FPC documentation. Alternative methods of test to the reference methods specified in the standard may be adopted, except for initial type testing and in case of dispute, provided that these alternative methods satisfy the following: a) A re

27、lationship can be shown to exist between the results from the reference test and those from the alternative test, and b) The information on which the relationship is based is available. The results of testing shall meet the specified compliance criteria and shall be recorded. For production evaluati

28、on the manufacturer could define the conformity criteria in the FPC documentation. The conformity of the production may be evaluated in a number of ways including acceptance by variables, assessment by attributes or assessment based on individual results. One method of satisfying this for production

29、 processes is to use the approach given in ISO 12491. Manufacturers inspection scheme for finished product testing is given in Table 3. The frequency of testing given in the inspection scheme may be reduced where it may be shown that the required compliance values are consistently achieved. Thus whe

30、re a higher level of consistency is achieved, a lower level of testing may be adopted. 2.3.2 Test equipment All weighing, measuring and testing equipment that has an influence on the declared values shall be calibrated and regularly inspected according to the documented procedures and frequencies, a

31、s stated in the factory production control manual. Manufacturers inspection schemes and the calibration criteria for equipment are given in Table 4. 2.4 Statistical techniques Where and when possible and applicable, the results of inspections and testing shall be interpreted by means of statistical

32、techniques, by attributes or by variables, to verify the product characteristics and to determine if the production conforms with the compliance criteria and the product conforms with the declared values. 2.5 Traceability marking and stock control of products The marking and stock control shall be d

33、ocumented. Products should be identifiable and traceable with regard to their production origin. Only conforming products shall be CE marked. Manufacturers inspection scheme for the manufacturer for marking and stock control is given in Table 5. CEN/TR 15225:20057 2.6 Non-conforming products The pro

34、cedure for dealing with non-conforming products shall be documented. Products that do not conform to the requirements shall be segregated and marked accordingly. However, these may be reclassified by the manufacturer and given different declared values. The manufacturer shall take action to avoid a

35、recurrence of the non-conformity. 3 Inspection schemes The checklists in these tables are to be used as guidance to Notified Bodies and manufacturers. The frequencies given in these tables represent the initial position and they may be reduced on the basis of satisfactory long-term product test perf

36、ormance. The inspections may be made directly by the manufacturer or under the responsibility of the manufacturer. The announced surveillance inspections by the Notified certification Body shall be carried out at least once per year. CEN/TR 15225:20058 Table 1 Inspection of raw materials Subject Pur

37、pose of inspection Method/procedure Frequency of inspection by manufacturer - Inspection of delivery note - Every delivery Binder Identification of suitable raw materials - Visual inspection or otherappropriate procedures - At appropriate time intervals as given in the FPC documentation - Inspection

38、 of delivery note - Every delivery Aggregate Identification of suitable raw materials - Visual inspection or otherappropriate procedures - At appropriate time intervals as given in the FPC documentation - Inspection of delivery note - Every delivery Additives Identification of suitable raw materials

39、 - Visual inspection or otherappropriate procedures - At appropriate time intervals as given in the FPC documentation - Inspection of delivery note - Every delivery Admixtures Identification of suitable raw materials - Visual inspection or otherappropriate procedures - At appropriate time intervals

40、as given in the FPC documentation Mixing water Establishment of suitability for production of mortar - Visual inspection or other appropriate procedures - At appropriate time intervals as given in the FPC documentation Storage of raw materials To check storage of materials for contamination in areas

41、 designated by the manufacturer - Visual inspection or other appropriate procedures - At appropriate time intervals as given in the FPC documentation NOTE 1 The delivery, transportation and storage systems may not always allow access to visual inspection (e.g. dry materials in closed tank and pipe s

42、ystems). NOTE 2 Visual inspections may have to be integrated with periodical tests on the relevant materials to ascertain their suitability. CEN/TR 15225:20059 Table 2 Inspection of production equipment Subject Purpose of inspection Method/procedure Frequency of inspection by manufacturer Correct fu

43、nctioning Visual inspection or other appropriate procedures - Daily Weighing equipment: Calibration with apparatus, which is calibrated in accordance with the national calibration requirements - On (re) installation - once in two years Weighing equipment and volumetric dosing equipment Controlling o

44、f the manufacturers declared accuracy Volumetric dosing equipment: Calibration by appropriate methods - On (re) installation - once in two year Mixer Control-of correct operation Visual inspection or other appropriate procedures - Weekly CEN/TR 15225:200510 Table 3 Tests on finished product (designe

45、d masonry mortars in accordance with EN 998-2) Subject Purpose of inspection Reference method/ procedure Frequency of test by manufacturer Properties of fresh mortar Chloride content 1)(for masonry mortars intended for reinforced masonry) Conformity with the declared value, if any - EN 1015-17 Every

46、 2500 m 3 or every 4000 tons, with- a minimum of once every 4 weeks and - a maximum of three times every 4 weeks Hardened mortar properties Compressive strength Conformity with the category or declared value - EN 1015-11 Every 2500 m 3 or every 4000 tons, with - a minimum of once every 4 weeks and -

47、 a maximum of three times every 4 weeks Bond strength 2)(for designed masonry mortars intended to be used in elements subject to structural requirements) Conformity with the tabulated value or declared value EN 1052-3 or by declaration from EN 998-2, annex C - Once a year, Water absorption 2 ) (for

48、masonry mortars intended to be used in external elements) Conformity with the declared value if any EN 1015-18 - Initial type testing Water vapour permeability 2 ) (for masonry mortars intended to be used in external elements) Conformity with the tabulated value or declared value, if any EN 1745 or

49、by declaration from EN 1745, Table A.12 - Initial type testing Thermal conductivity 2 ) (for masonry mortars intended to be used in elements subject to thermal insulation requirements) Conformity with the tabulated value or declared value, if any EN 1745 or by declaration from EN 1745, Table A.12 - Initial type test