BS ISO 6262-1-2013 End mills with indexable inserts End mills with flatted cylindrical shank《装可转位刀片的立铣刀 削平型直柄立铣刀》.pdf

《BS ISO 6262-1-2013 End mills with indexable inserts End mills with flatted cylindrical shank《装可转位刀片的立铣刀 削平型直柄立铣刀》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 6262-1-2013 End mills with indexable inserts End mills with flatted cylindrical shank《装可转位刀片的立铣刀 削平型直柄立铣刀》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 6262-1:2013End mills with indexableinsertsPart 1: End mills with flatted cylindricalshankBS ISO 6262-1:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 6262-1:2013. It supersedes BS4193-9:1982 which is withdrawn.The UK partic

2、ipation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a con

3、tract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013ISBN 978 0 580 81021 3 ICS 25.100.20 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the

4、 authority of the Standards Policy and Strategy Committee on 30 September 2013.Amendments/corrigenda issued since publicationDate Text affectedBS ISO 6262-1:2013 ISO 2013End mills with indexable inserts Part 1: End mills with flatted cylindrical shankFraises en bout plaquettes amovibles Partie 1: Fr

5、aises queue cylindrique mplatINTERNATIONAL STANDARDISO6262-1Second edition2013-09-01Reference numberISO 6262-1:2013(E)BS ISO 6262-1:2013ISO 6262-1:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication m

6、ay be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of th

7、e requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 6262-1:2013ISO 6262-1:2013(E) ISO 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13

8、Dimensions . 1Annex A (informative) Relationship between designations in this part of ISO 6262 and the ISO 13399 series . 3Bibliography 4BS ISO 6262-1:2013ISO 6262-1:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO me

9、mber bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governme

10、ntal and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance

11、 are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is draw

12、n to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on t

13、he ISO list of patent declarations received. www.iso.org/patentsAny trade name used in this document is information given for the convenience of users and does not constitute an endorsement.The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with cutting e

14、dges made of hard cutting materials.This second edition cancels and replaces the first edition (ISO 6262-1:1982), of which it constitutes a minor revision.ISO 6262 consists of the following parts, under the general title End mills with indexable inserts: Part 1: End mills with flatted cylindrical sh

15、ank Part 2: End mills with Morse taper shankiv ISO 2013 All rights reservedBS ISO 6262-1:2013INTERNATIONAL STANDARD ISO 6262-1:2013(E)End mills with indexable inserts Part 1: End mills with flatted cylindrical shank1 ScopeThis part of ISO 6262 specifies the dimensions of end mills with indexable ins

16、erts and flatted parallel shank according to ISO 3338-2.The form and dimensions of the inserts are left to the discretion of the manufacturer.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable to its application. For

17、dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 3338-2, Cylindrical shanks for milling cutters Part 2: Dimensional characteristics of flatted cylindrical shanks3 DimensionsaThe value of 90

18、shall be the nominal value of the cutting edge angle of the insert. The effective angle obtained on the workpiece depends on the geometry and the diameter of the milling cutter together with the cutting depth.Figure 1 Dimensions ISO 2013 All rights reserved 1BS ISO 6262-1:2013ISO 6262-1:2013(E)Table

19、 1 Dimensions Dimensions in millimetresd js14d1ah6l1maxl16 16 25 7520 20 30 8225 25 38 9632 32 38 10040 32 48 11050 32 48 110aThe shank dimensions and configuration shall be in accordance with ISO 3338-2.2 ISO 2013 All rights reservedBS ISO 6262-1:2013ISO 6262-1:2013(E)Annex A (informative) Relation

20、ship between designations in this part of ISO 6262 and the ISO 13399 seriesFor the relationship between designations in this part of ISO 6262 and preferred symbols according to ISO 13399 (all parts), see Table A.1.Table A.1 Relationship between designations in this part of ISO 6262 and the ISO 13399

21、 seriesSymbol in ISO 6262-1 (this part of ISO 6262)Reference in ISO 6262-1 (this part of ISO 6262)Property name in the ISO 13399 seriesSymbol in the ISO 13399 seriesReference in the ISO 13399 seriesd Figure 1 and Table 1 Cutting diameter DCISO/TS 13399-3, 71D084653E57Fd1Figure 1 and Table 1 Connecti

22、on diameter DCONISO/TS 13399-3, 71EBDBF5060E6l1Figure 1 and Table 1 Head length LHISO/TS 13399-3, 71D07574A61E8l Figure 1 and Table 1 Overall length OALISO/TS 13399-3, 71D078EB7C08690 Figure 1Tool cutting edge angleKAPRISO/TS 13399-3, 71D078F683C9B ISO 2013 All rights reserved 3BS ISO 6262-1:2013ISO

23、 6262-1:2013(E)Bibliography1 ISO 13399 (all parts), Cutting tool data representation and exchange4 ISO 2013 All rights reservedBS ISO 6262-1:2013BS ISO 6262-1:2013ISO 6262-1:2013(E) ISO 2013 All rights reservedICS 25.100.20Price based on 4 pagesThis page deliberately left blankBSI is the national bo

24、dy responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarter

25、s389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable for

26、mat and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by v

27、isiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you

28、need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription product

29、s go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substan

30、tial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replace

31、d. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre

32、available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or

33、 ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in t

34、he information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted

35、 in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW