BS 7776-1995 Glossary of torque terminology for threaded fasteners《螺纹紧固件扭矩术语词汇》.pdf
《BS 7776-1995 Glossary of torque terminology for threaded fasteners《螺纹紧固件扭矩术语词汇》.pdf》由会员分享,可在线阅读,更多相关《BS 7776-1995 Glossary of torque terminology for threaded fasteners《螺纹紧固件扭矩术语词汇》.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD BS 7776:1995 Glossary of Torque terminology for threaded fasteners UDC 531.232:001.4:621.88BS7776:1995 This British Standard, having been prepared under the directionof the General Mechanical Engineering Standards Policy Committee, waspublished under the authorityof the Standards Bo
2、ardand comes into effect on 15February 1995 BSI 07-1999 The following BSI references relate to the work on this standard: Committee reference GME/9 Draft for comment 93/712368 DC ISBN 0 580 23253 0 Committees responsible for this British Standard The preparation of this British Standard was entruste
3、d by the General Mechanical Engineering Standards Policy Committee (GME/-) to Technical Committee GME/9, upon which the following bodies were represented: BEAMA Ltd. British Constructional Steelwork Association Ltd. British Industrial Fasteners Federation British Steel Industry British Steel Industr
4、y (Wire Section) Gauge and Tool Makers Association National Association of Fastener Stockholders Society of Motor Manufacturers and Traders Limited Washer Manufacturers Association of Great Britain The following bodies were also represented in the drafting of the standard, through subcommittees and
5、panels: National Centre of Tribology Society of British Aerospace Companies Ltd. Amendments issued since publication Amd. No. Date CommentsBS7776:1995 BSI 07-1999 i Contents Page Committees responsible Inside front cover Foreword ii Glossary 1BS7776:1995 ii BSI 07-1999 Foreword This British Standard
6、 has been prepared under the direction of the General Mechanical Engineering Standards Policy Committee and includes definitions of terms relating to the torque terminology of fasteners. In the design, assembly, quality assessment and standardization of threaded fasteners and joints, expressions are
7、 frequently used which relate to the various torque functions which are required to be applied or assessed. Much confusion is generated by the multiplicity of terms used throughout industry. As a basic reference document providing a comprehensive list of terms, this glossary is intended to promote b
8、etter understanding between the various sections of industry and the users of fasteners. Many of the definitions in this glossary are essentially the same as those used in other British Standards already published. As these British Standards are revised and new standards are produced, the use of the
9、 definitions given in this glossary will be encouraged in order to promote wider acceptance and recognition of standard terminology. In this glossary, terms are arranged in alphabetical order. In the definitions, italics have been used to indicate terms that are defined elsewhere in this glossary. A
10、 British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a
11、 front cover, an inside front cover, pages i and ii, pages1 and 2 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS7776:1995 BSI 07-1999 1 Glossary No. Term Defini
12、tion 1 break loose torque The torque, applied in the reverse direction to tightening, required to initiate rotation of a tightened fastenerthus releasing the assembled clamping force. 2 cam-out torque The maximum torque which can be applied to a fastener assembly tool before the end load required to
13、 maintain functional contact between the tool and the driving recess exceeds that which can be considered as a nominal manual pressure. 3 free-running torque The torque required to rotate a threaded fastener during assembly with a mating threaded component before either of the following occurs: a) a
14、 clamping force is generated; or b) it comes into contact with a device which displays frictional resistance to rotation. 4 prevailing torque The torque necessary to overcome the resistance to rotation generated by a prevailing torque feature, measured with the fastener approximately in constant mot
15、ion and with no clamping force developed against the bearing surface of the fastener. 5 prevailing torque feature A feature of a threaded fastener which displays frictional resistance to rotation due to a self-contained device. NOTEThe frictional resistance is not a consequence of a clamping force d
16、eveloped against the bearing surface of the fastener. 6 removal torque The torque necessary to rotate a threaded fastener, applied in the reverse direction to the tightening torque after the clamping force has been released. 7 self-locking A generic term used to indicate resistance to rotation. NOTE
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS77761995GLOSSARYOFTORQUETERMINOLOGYFORTHREADEDFASTENERS 螺纹 紧固 扭矩 术语 词汇 PDF

链接地址:http://www.mydoc123.com/p-547038.html