BS EN 62384-2006 D C or A C supplied electronic control gear for LED modules - Performance requirements《发光二极管模块的交直流电源电子控制装置 性能要求》.pdf

《BS EN 62384-2006 D C or A C supplied electronic control gear for LED modules - Performance requirements《发光二极管模块的交直流电源电子控制装置 性能要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 62384-2006 D C or A C supplied electronic control gear for LED modules - Performance requirements《发光二极管模块的交直流电源电子控制装置 性能要求》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 62384:2006DC or AC supplied electronic control gear for LED modules Performance requirementsThe European Standard EN 62384:2006 has the status of a British StandardICS 29.140.99; 31.080.99g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g

2、50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: Wang Bin, na, Tue Mar 27 03:25:11 GMT+00:00 2007, Uncontrolled Copy, (c) BSIBS EN 62384:2006This British Standard was published under the authority of the Standards Policy and

3、 Strategy Committee on 30 November 2006 BSI 2006ISBN 0 580 49678 3National forewordThis British Standard was published by BSI. It is the UK implementation of EN 62384:2006. It is identical with IEC 62384:2006.The UK participation in its preparation was entrusted by Technical Committee CPL/34, Lamps

4、and related equipment, to Subcommittee CPL/34/3, Auxiliaries for lamps.A list of organizations represented on CPL/34/3 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct applicatio

5、n.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsLicensed Copy: Wang Bin, na, Tue Mar 27 03:25:11 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEUROPEAN STANDARD EN 62384 NORME EUROPENNE EUROPISCHE NORM September

6、2006 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2006 CENELEC - All rights of exploitation in any form and by any means rese

7、rved worldwide for CENELEC members. Ref. No. EN 62384:2006 E ICS 29.140.99; 31.080.99 English version DC or AC supplied electronic control gear for LED modules - Performance requirements (IEC 62384:2006) Appareillages lectroniques aliments en courant continu ou alternatif pour modules de DEL - Exige

8、nces de performances (CEI 62384:2006) Gleich- oder wechselstromversorgte elektronische Betriebsgerte fr LED-Module - Anforderungen an die Arbeitsweise (IEC 62384:2006) This European Standard was approved by CENELEC on 2006-09-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regu

9、lations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. Th

10、is European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC membe

11、rs are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,

12、Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang Bin, na, Tue Mar 27 03:25:11 GMT+00:00 2007, Uncontrolled Copy, (c) BSIForeword The text of document 34C/752/FDIS, future edition 1 of IEC 62384, prepared by SC 34C, Auxiliaries for lamps, of IEC TC 34, Lamps and related equipment, was

13、submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 62384 on 2006-09-01. This standard is to be used in conjunction with EN 61347-2-13. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national

14、 standard or by endorsement (dop) 2007-06-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2009-09-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 62384:2006 was approved by CENELEC as a European

15、Standard without any modification. _ EN 62384:2006 2 Licensed Copy: Wang Bin, na, Tue Mar 27 03:25:11 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 3 EN 62384:2006 CONTENTS 1 Scope 4 2 Normative references .4 3 Terms and definitions .4 4 General notes on tests5 5 Classification5 5.1 Classification acco

16、rding to the load5 5.2 Classification according to the output voltage.6 5.3 Classification according to the output current .6 6 Marking6 6.1 Mandatory marking 6 6.2 Optional marking .6 7 Output voltage and current .6 7.1 Starting and connecting requirements 6 7.2 Voltage and current during operation

17、 .7 7.3 Capacitive load requirement.7 7.4 Voltage surges during switching and operation.7 8 Total circuit power 7 9 Circuit power factor 7 10 Supply current 7 11 Impedance at audio-frequencies .8 12 Operational tests for abnormal conditions8 13 Endurance8Annex A (normative) Tests.10 Annex B (informa

18、tive) A guide to quoting product life and failure rate13Annex ZA (normative) Normative references to international publications with their corresponding European publications 15 Bibliography. 14 Licensed Copy: Wang Bin, na, Tue Mar 27 03:25:11 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 62384:2006

19、4 DC OR AC SUPPLIED ELECTRONIC CONTROL GEAR FOR LED MODULES PERFORMANCE REQUIREMENTS 1 Scope This international standard specifies performance requirements for electronic control gear for use on d.c. supplies up to 250 V and a.c. supplies up to 1 000 V at 50 Hz or 60 Hz with an output frequency whic

20、h can deviate from the supply frequency, associated with LED modules according to IEC 62031. Control gear for LED modules specified in this standard are designed to provide constant voltage or current. Deviations from the pure voltage and current types do not exclude the gear from this standard. NOT

21、E 1 The tests in this standard are type tests. Requirements for testing individual control gear during production are not included. NOTE 2 Requirements for control gear which incorporate means for varying the output power are under consideration. NOTE 3 It may be expected that control gear complying

22、 with this standard will ensure satisfactory operation between 92 % and 106 % of the rated supply voltage, taking into account the specifications of the LED module manufacturer. 2 Normative references The following referenced documents are indispensable for the application of this document. For date

23、d references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61347-2-13, Lamp controlgear Part 2-13: Particular requirements for d.c. or a.c. supplied electronic control gear for LED modules IEC 62031, LED

24、 modules for general lighting Safety requirements 1 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 total circuit power total power dissipated by control gear and LED module(s) in combination, at rated supply voltage of the control gear and a

25、t the highest rated output load. 3.2 circuit power factor ratio of the measured circuit power to the product of the supply voltage (r.m.s.) and the supply current (r.m.s.). 3.3 high audio-frequency impedance control gear control gear the impedance of which in the frequency range 250 Hz to 2 000 Hz e

26、xceeds the values specified in Clause 11 of this standard. Licensed Copy: Wang Bin, na, Tue Mar 27 03:25:11 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 5 EN 62384:2006 4 General notes on tests 4.1 The tests according to this standard are type tests. NOTE The requirements and tolerances permitted by t

27、his standard are based on testing of a type test sample submitted by the manufacturer for that purpose. In principle this type test sample should consist of units having characteristics typical of the manufacturers production and be as close to the production centre point values as possible. It may

28、be expected with the tolerances given in the standard that products manufactured in accordance with the type test sample will comply with the standard for the majority of the production. Due to the production spread however, it is inevitable that there will sometimes be products outside the specifie

29、d tolerances. For guidance of sampling plans and procedures for inspection by attributes, see IEC 60410. 4.2 For tests which are carried out with a LED module or LED modules, this (these) LED module(s) shall fulfil the following requirements: The wattage of the LED module(s) when measured at its(the

30、ir) rated voltage or rated current (d.c. and/or a.c.) shall not differ from the rated wattage by more than +6 % and 0 %. 4.3 The tests shall be carried out in the order of the clauses, unless otherwise specified. 4.4 One specimen shall be submitted to all the tests. 4.5 In general all the tests are

31、made on each type of control gear or, where a range of similar control gear is involved for each rated wattage in the range or on a representative selection from the range as agreed with the manufacturer. 4.6 The tests shall be made under the conditions specified in Clause A.1. Since up to now data

32、of LED modules are not published in an IEC standard, they shall be made available by the LED module manufacturer. 4.7 All control gear covered by this standard shall comply with the requirements of IEC 61347-2-13. 4.8 The tests shall be carried out with the length of the output cable of both 20 cm a

33、nd 200 cm unless otherwise declared by the manufacturer. 5 Classification 5.1 Classification according to the load a) Single value load control gear This type of control gear is designed for use with one specific output wattage only, which may be dissipated by one or more LED modules. b) Multiple va

34、lue load control gear This type of control gear is designed for use with one or more LED modules with a total load within the declared wattage range. Licensed Copy: Wang Bin, na, Tue Mar 27 03:25:11 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEN 62384:2006 6 5.2 Classification according to the output

35、voltage a) Control gear having a stabilised output voltage b) Control gear without a stabilised output voltage 5.3 Classification according to the output current a) Control gear having a stabilised output current b) Control gear without a stabilized output current 6 Marking 6.1 Mandatory marking 6.1

36、.1 Control gear shall be clearly marked as follows: Circuit power factor; e.g. = 0,9 If the power factor is less than 0,95 leading, it shall be followed by the letter “C”, e.g. = 0,9 C. 6.1.2 In addition to the above mandatory marking, the following information shall either be given on the control g

37、ear or made available in the manufacturers catalogue or the like: a) if applicable: limits of the permissible temperature range; b) if applicable: an indication that the control gear has a stabilised output voltage; c) if applicable: an indication that the control gear has a stabilised output curren

38、t; d) if applicable: an indication that the control gear is suitable for operation with a mains supply dimmer; e) if applicable: an indication of the operation mode, e.g. phase control. 6.2 Optional marking The following information may either be given on the control gear or made available in the ma

39、nufacturers catalogue or the like: a) total circuit power; b) if applicable: the symbol Z which indicates that the control gear is designed to comply with conditions for audio-frequency impedance; c) If applicable: a symbol which indicates that the control gear is a short-circuit proof type (the sym

40、bol is under consideration). 7 Output voltage and current 7.1 Starting and connecting requirements After starting or connecting a LED module, the output should be within 110 % of its rated value within 2 s. Maximum current or maximum voltage shall not exceed the values given by the manufacturer. Thi

41、s performance is tested with the minimum rated power. NOTE If the output voltage is a.c., 110 % is the percentage of the r.m.s. value, if d.c., 110 % is the percentage of the d.c. value. Licensed Copy: Wang Bin, na, Tue Mar 27 03:25:11 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 7 EN 62384:2006 7.2 V

42、oltage and current during operation For control gear having a non-stabilised output voltage, when supplied with the rated supply voltage, the output voltage shall not differ by more than 10 % from the rated voltage of the LED modules; for control gear having a stabilised output voltage when supplied

43、 at any supply voltage between 92 % and 106 % of the rated supply voltage, the output voltage shall not differ by more than 10 % from the rated voltage of the LED modules. For control gear having a non-stabilised output current, when supplied with the rated supply voltage, the output current shall n

44、ot differ by more than 10 % from the rated current of the LED modules; for control gear having a stabilised output current when supplied at any supply voltage between 92 % and 106 % of the rated supply voltage, the output current shall not differ by more than 10 % from the rated current of the LED m

45、odules. Multiple load control gear shall be tested with both the minimum and maximum load. 7.3 Capacitive load requirement If the LED module or any additional control unit connected to the convertor contain capacitors for control and/or driving circuitry on the modules, current pulses may be generat

46、ed when connecting the LED module to the control gear. This shall not disturb the control gear overcurrent detection nor the starting process of the control gear. For test conditions, See clause A.2. Figure A.1a describes a test circuit during the starting process of the control gear and figure A.1b

47、 describes a test circuit for connecting the load during steady state operation. Compliance: when connecting the measurement circuit to the control gear, the detection device shall not trip. 7.4 Voltage surges during switching and operation Voltage surges superimposed on the output voltage shall not

48、 exceed the values specified below (values under consideration). 8 Total circuit power At rated voltage, the total circuit power shall not be more than 110 % of the value declared by the manufacturer, when the control gear is operated with LED module(s). 9 Circuit power factor The measured circuit p

49、ower factor shall not be less than the marked value by more than 0,05 when the control gear is operated on its rated wattage with LED module(s) and the whole combination is supplied with rated voltage and frequency. 10 Supply current At rated voltage, the supply current shall not differ by more than +10 % from the value marked on the control gear or declared in the manufacturers literature, when that control gear is operated on its rated wattage with LED module(s). Licensed Copy: Wang Bin, na, Tue Mar 27 03:25:11 GMT