BS 3G 100-2 3 9-1972 Specification for general requirements for equipment for use in aircraft - All equipment - Environmental conditions - Ice formation《飞机设备的一般要求规范 第2部分 各种设备 第3节 环.pdf

《BS 3G 100-2 3 9-1972 Specification for general requirements for equipment for use in aircraft - All equipment - Environmental conditions - Ice formation《飞机设备的一般要求规范 第2部分 各种设备 第3节 环.pdf》由会员分享，可在线阅读，更多相关《BS 3G 100-2 3 9-1972 Specification for general requirements for equipment for use in aircraft - All equipment - Environmental conditions - Ice formation《飞机设备的一般要求规范 第2部分 各种设备 第3节 环.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS 3G. 100-2.3.9: 1972 Specification for General requirements for equipment in aircraft Part 2: All equipment Section3:Environmental conditions Subsection 3.9: Ice formation UDC 629.7.05/.06:551.574.7BS 3G. 100-2.3.9:1972 This British Standard, having been approved

2、by the AerospaceIndustry Standards Committee, was published underthe authority of the Executive Board of the Institutionon 14 June, 1972 BSI 02-1999 The following BSI references relate to the work on this standard: Committee reference ACE/58 Draft for comment 70/26883 ISBN 0580 07173 1 Amendments is

3、sued since publication Amd. No. Date CommentsBS 3G. 100-2.3.9:1972 BSI 02-1999 i Contents Page Foreword ii 1. Scope 1 2. General 1 3. General test procedures 1 3.1 Test conditions 1 3.2 Test details 1 3.3 Test requirements 1 3.4 Initial measurements 1 3.5 Operational checks 1 4. Test A 1 4.1 Field o

4、f application 1 4.2 Test procedure 1 4.3 Information to be stated in the relevant specification 2 5. Test B 2 5.1 Field of application 2 5.2 Test procedure 2 5.3 Information to be stated in the relevant specification 2 6. Test C 2 6.1 Field of application 2 6.2 Test procedure 2 6.3 Information to be

5、 stated in the relevant specification 3BS 3G. 100-2.3.9:1972 ii BSI 02-1999 Foreword This British Standard is part of a composite standard in the Aerospace Series of British Standards specifying general requirements for equipment in aircraft. An introduction to the complete British Standard is given

6、 in BritishStandard3G. 100-0. This subsection of this standard supersedes the icing requirements stated in the current revision of 2G. 100-2 (Clauses 210 and 211). It details three types of test to evaluate the effects of the formation of ice on aircraft equipment. A further British Standard in the

7、Aerospace Series relating to the accretion of ice by external equipment exposed to supercooled water droplets or ice crystals is in the course of preparation. This subsection makes reference to the following British Standards: 3G. 100-2-3.0, Standard test requirements. 3G. 100-2-3.2, Temperature-pre

8、ssure requirements. NOTEThe figures in metric units are to be regarded as the standard. The conversions to imperial units are approximate. Accurate conversions should be based upon BS 350, “Conversion factors and tables”. Information concerning metric (SI) units is given in BS 3763, “The Internation

9、al System of units (SI)”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of page

10、s This document comprises a front cover, an inside front cover, pages i and ii, pages1 to 3 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front cover.BS 3G. 100-2.3.9:1972 BSI

11、 02-1999 1 1 Scope This British Standard defines tests to evaluate the effect of various icing conditions on the performance of components or equipment in aircraft. It should be read in conjunction with British Standard 3G. 100-0. Three different tests are given, each of which has a specific field o

12、f application. The relevant equipment specification will prescribe which test is to be used and also the appropriate functional checks. 2 General Icing tests are specified to simulate the effect that occurs when an aircraft flying in a cold atmosphere encounters free water or descends through cloud

13、or into a moist atmosphere near the ground. Ice may build up on the equipment immediately, or frosting or condensation may occur and freeze to ice, of a thickness dependent upon the quantity of moisture in the air and the temperature and the thermal capacity of the equipment. The tests also simulate

14、 the converse effect when water, which may have been trapped or has condensed inside equipment, or may have collected in pockets on the outside either through wet conditions on the ground, or through accumulation of moisture by frosting and subsequent melting of the frost, freezes as the aircraft as

15、cends. The accretion of ice, from whatever cause, may interfere with the necessary movement of parts. Films of ice may form on normally open electric contacts and maintain an open circuit even when the contacts are operated. The tests specified in the following clauses are intended to evaluate: 1) t

16、he performance of equipment with ice or frost adhering to it, 2) the effects of refrozen water from molten ice or from condensation, 3) the performance of the equipments anti-icing or de-icing system. The objective of the test shall be clearly stated in the relevant equipment specification. 3 Genera

17、l Test Procedures 3.1 Test conditions. The item to be tested shall, in all cases, be in a condition representative of operational use. Un-representative coatings and contaminants, such as oil, grease and dirt, which could affect the adhesion between the ice and the surfaces of the equipment, shall b

18、e removed before commencing this test. 3.2 Test details. The selected icing test specified in the relevant equipment specification shall be conducted in accordance with the procedures described in the following clauses. 3.3 Test requirements. For the purposes of this standard the appropriate require

19、ments stated in British Standard 3G. 100-2-3.0, shall apply. 3.4 Initial measurements. The equipment shall be visually examined and electrically and/or mechanically checked, as required by the relevant equipment specification. 3.5 Operational checks. The operation of the equipment shall be checked a

20、t the most adverse phase of the test, which for most applications would be a switch-on or start-up under icing conditions. Excessive operation of equipment which generates heat should be avoided since this could mitigate the effects of the test. For tests demonstrating survival of the equipment only

21、, the equipment shall be operated and a performance evaluation made when the temperature and humidity have returned to standard laboratory conditions. 4 Test A 4.1 Field of application. This test applies to equipment in which there is movement of parts, e.g.electrical contacts, contained within a no

22、n-sealed enclosure 1) , and where the equipment is so located and its duty cycle is such that the temperature of the equipment could vary during flight and on the ground within limits that would produce conditions of both condensation and freezing. The relevant equipment specification shall specify

23、whether it is permissable during the functioning tests for more than one attempt to be made to obtain satisfactory operation. 4.2 Test procedure. The test shall be conducted in accordance with the requirements of Test D, Method2, Specified in British Standard 3G. 100-2-3.2, and may for convenience f

24、orm part of that test. When the temperature of the equipment has risen to5 3 C and before the restoration of the chamber pressure to ground level, a functional test shall be conducted to check for satisfactory operation. If, in the case of vented equipment, there is a possibility of the vent hole(s)

25、 being closed by the presence of ice, the test procedure shall be amended so that pressure is restored before the ice has melted. 1) A non-sealed enclosure is one in which moist air may penetrate during the test.BS 3G. 100-2.3.9:1972 2 BSI 02-1999 4.3 Information to be stated in the relevant specifi

26、cation. When this test is a requirement in the relevant equipment specification the following information shall be stated, as far as is applicable: 5 Test B 5.1 Field of application. This test applies to all equipment in which there is movement of parts and where such movement could be prevented or

27、impeded by ice forming as the result of progressive accumulation of water inside non-sealed enclosures where positive drainage is not provided. 5.2 Test procedure. The equipment shall be conditioned to a temperature of 20 C until temperature stabilization has been achieved. The chamber pressure shal

28、l then be reduced to that used in Test C specified in British Standard 3G. 100-2-3.2, but not lower than at an altitude of 15200 m (50000 ft). After a period of not less than 10 min the temperature of the chamber shall be raised at a rate not exceeding 3 C per minute and humidified so that the chamb

29、er humidity is held at or close to saturation. The chamber temperature shall not at any time exceed + 30 C. When the equipment has reached a temperature above 0 C and after a period which would allow all frost or ice to melt, the pressure shall be increased to that corresponding to ground level at a

30、 uniform rate in a period of 15 min to 30min. At the completion of the repressurization the next cycle shall be commenced. A total of twenty-five such cycles shall be made consecutively. If it becomes necessary to interrupt this sequence the interruption shall take place whilst the equipment is held

31、 in the low temperature condition. 5.2.1 A functional check, or checks, shall be made, as required by the relevant equipment specification, at the lowest temperature in the cycle. 5.3 Information to be stated in the relevant specification. When this test is a requirement in the relevant equipment sp

32、ecification the following information shall be stated, as far as is applicable: 6 Test C 6.1 Field of application. This test applies to items mounted externally or in non-temperature controlled bays where there is a real risk of accretion of free water which could subsequently freeze on the cold sur

33、faces of the items. The test is intended to examine the effects of a representative thickness of ice on the performance of the item, or to determine the maximum thickness that can be permitted before de-icing action is necessary. 6.1.1 The relevant equipment specification shall state the thickness a

34、nd distribution of ice or whether a progressive build-up of ice is required. 6.2 Test procedure. The equipment shall be conditioned in a low temperature chamber until its temperature has stabilized at a level, determined by previous experiments, that will permit hard clear ice to form on the item wh

35、en water is sprayed upon it. The optimum temperature is likely to be between1 C and 10 C, depending upon the thermal mass of the item. A homogeneous layer of hard clear ice (not white or air pocketed) shall be produced on the relevant surfaces of the item, to the required thickness and distribution,

36、 by hand spraying with a fine mist of water, the temperature of which is close to freezing. When the ice formation has reached the level specified in the relevant equipment specification, spraying shall be stopped and the test temperature restablized, unless otherwise stated, at the relevant Test C

37、low temperature given in Table1 and Table2 of Part 2:Section 3:Subsection 3.2 of BritishStandard3G. 100, before making the performance checks required by the relevant equipment specification. 6.2.1 For tests requiring a progressive increase in the thickness of ice, and when it is important that the

38、ice be homogeneous (not layered), separate tests shall be made in which the ice is formed to the specified thickness in one continuous operation. Relevant clause 1) Object of test 2 2) Initial measurements 3.4 3) Operational checks required 3.5 4) Permissible number of attempts to operate 4.1 Releva

39、nt clause 1) Object of test 2 2) Initial measurements 3.4 3) Operational checks 3.5 and 5.2.1BS 3G. 100-2.3.9:1972 BSI 02-1999 3 6.3 Information to be stated in the relevant specification. When this test is a requirement in the relevant equipment specification the following information shall be stat

40、ed, as far as is applicable: Relevant clause 1) Object of test 2 2) Initial meaurements 3.4 3) Required build-up of ice 6.1.1 4) Operational checks 3.5BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

41、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards i

42、n Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our

43、 products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI off

44、ers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8

45、996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international

46、 standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept

47、up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the cop

48、yright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or other

49、wise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.