BS 2690-102-1979 Methods of testing water used in industry - Hydrazine spectrophotometric method (4-dimethylaminobenzaldehyde)《工业用水试验方法 第102部分 联氨 分光光度法(4-二甲氨基苯甲醛)》.pdf

《BS 2690-102-1979 Methods of testing water used in industry - Hydrazine spectrophotometric method (4-dimethylaminobenzaldehyde)《工业用水试验方法 第102部分 联氨 分光光度法(4-二甲氨基苯甲醛)》.pdf》由会员分享，可在线阅读，更多相关《BS 2690-102-1979 Methods of testing water used in industry - Hydrazine spectrophotometric method (4-dimethylaminobenzaldehyde)《工业用水试验方法 第102部分 联氨 分光光度法(4-二甲氨基苯甲醛)》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 2690-102: 1979 Methods of testing Water used in industry Part 102: Hydrazine: spectrophotometric method (4-dimethylaminobenzaldehyde) IMPORTANT NOTE. It is essential that this Part be read in conjunction with the information in Part100 of this standard, “Foreword, scope and gener

2、al requirements”, which is published separately. UDC 628.1:663.63.01:543.3:546.171.5BS2690-102:1979 This British Standard, having been prepared under the direction of the Environment and Pollution Standards Committee, was published under the authority of the Executive Board on 31 January 1979 BSI 08

3、-1999 The following BSI references relate to the work on this standard: Committee reference EPC/37 Draft for comment 77/50234 DC ISBN 0 580 10613 6 A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct

4、application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2 and a back cover. This standard has been updated (see copyright date) and may have h

5、ad amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date of issue CommentsBS2690-102:1979 BSI 08-1999 i Contents Page 1 Scope 1 2 Range 1 3 Maximum size of test portion 1 4 Principle 1 5 Interferences 1 6 R

6、eagents 1 7 Sampling 1 8 Preparation of calibration graph 1 9 Procedure 1 10 Calculation 2ii blankBS2690-102:1979 BSI 08-1999 1 1 Scope The method described is for the determination of hydrazine in industrial waters. 2 Range 0.5 4g to 5 4g hydrazine. 3 Maximum size of test portion The maximum size o

7、f test portion is 20 ml. 4 Principle Hydrazine reacts with 4-dimethylaminobenzaldehyde to give acid salts of the azine that are intensely red in strong solutions and yellow in dilute solutions. 5 Interferences Under the conditions described in the method the presence of 100 4g of ammonia, cyclohexyl

8、amine, morpholine, octadecylamine, iron, copper and nickel and 5000 4g of chloride, sulphate and phosphate either separately or collectively do not cause significant interference. 6 Reagents The following reagents are required. 6.1 4-dimethylaminobenzaldehyde solution. Dissolve 4.0 g of 4-dimethylam

9、inobenzaldehyde (grade for hydrazine determination) in 200 ml of methanol and 20 ml of concentrated hydrochloric acid, 36 % (m/m) (11N). Store in a dark bottle out of direct sunlight. 6.2 Hydrochloric acid solution, 0.5N. 6.3 Hydrochloric acid/methanol solution. Mix 20 ml of concentrated hydrochlori

10、c acid, 36 % (m/m) (11N), with 200 ml of methanol. 6.4 Hydrazine standard solutions 6.4.1 Hydrazine stock solution. Dissolve 0.082 g of hydrazine dihydrochloride in 0.5N hydrochloric acid and dilute with this acid to 1 litre. 6.4.2 Hydrazine working solution. Dilute 1 ml of hydrazine solution with 0

11、.5N hydrochloric acid to100 ml. 1 ml N 0.25 g N4 g N 2 H 4 . 7 Sampling If the temperature of the sample is above 25 C it is necessary to use an efficient stainless steel cooling coil so that the temperature of the sample is reduced to about 15 C to 25 C. Insert the outlet tube from the cooling coil

12、 into a 250 ml stoppered bottle so that it almost reaches the bottom. Allow the water to flow until a representative sample is obtained. Withdraw the outlet slowly and immediately stopper the bottle avoiding trapping any air bubbles in the bottle. The sample should then be analysed without delay. 8

13、Preparation of calibration graph Measure accurately volumes of the hydrazine working solution containing 0, 1, 2, 3, 4 and 5 4g of N 2 H 4into a series of previously dried 50 ml one-mark volumetric flasks, each containing 15 ml of 0.5N hydrochloric acid. Then add enough water to each flask to make t

14、he total volume approximately38 ml. Stopper and mix. Adjust the temperature of the contents of each flask to between20 C and 25 C, add 10 ml of 4-dimethylaminobenzaldehyde solution to each, make-up to the mark with water, stopper and mix. Allow to stand for 10 min. Measure the absorbance of each sol

15、ution using 40 mm cells at a known temperature between 20 C and 25 C in a spectrophotometer at the wavelength corresponding to maximum absorption (approximately 458 nm but the exact wavelength shall be checked for each spectrophotometer). Use water in the compensating cell. Deduct the reading for th

16、e blank solution containing no added hydrazine from those obtained for the standard solutions. Plot a graph of the net absorbance against corresponding micrograms of hydrazine. 9 Procedure Measure a suitable volume of the sample (not greater than 20 ml) into a 50 ml one-mark volumetric flask contain

17、ing 15 ml of the 0.5N hydrochloric acid. Add enough water to make the total volume approximately 38 ml. Stopper and mix. Adjust the temperature to within 1 C of the calibration temperature, add 10 ml of the 4-dimethylaminobenzaldehyde solution and make up to the mark with water. Stopper and mix. Mea

18、sure 20 ml of water into a second 50 ml one-mark volumetric flask containing 15 ml of the0.5N hydrochloric acid to serve as a blank. Stopper and mix. Adjust the temperature to within1 C of the calibration temperature, add10ml of the 4-dimethylaminobenzaldehyde solution, make up to the mark with wate

19、r. Stopper and mix. Allow to stand for 10 min.BS2690-102:1979 2 BSI 08-1999 Measure the absorbance of the sample solution and the blank solution using 40 mm cells in the spectrophotometer at a temperature within 1 C of that at which the calibration graph was prepared and at the same wavelength. Use

20、water in the compensating cell. If it is necessary to compensate for the colour of the sample, take a volume equal to that of the test portion and proceed as before but substituting 10 ml of the hydrochloric acid/methanol solution for the4-dimethylaminobenzaldehyde solution and making up to a volume

21、 of 50 ml with water. Measure the absorbance of this compensating solution against water. 10 Calculation Deduct the reading obtained for the blank solution and the colour compensating solution, if used, from that obtained for the sample solution and read off from the calibration graph the hydrazine

22、content of. the test portion. Hydrazine (as N 2 H 4 ), mg/l of test sample = where m is the mass of hydrazine in the test portion(4g) v is the volume of the test portion (ml). m v -3 blankBS 2690-102: 1979 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent

23、 national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess

24、 the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of

25、 which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standar

26、ds publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards

27、 BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Cen

28、tre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyrig

29、ht Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in a

30、ny form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.