AWWA C900-2016 Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings 4 In Through 60 In (100 mm Through 1 500 mm).pdf

《AWWA C900-2016 Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings 4 In Through 60 In (100 mm Through 1 500 mm).pdf》由会员分享，可在线阅读，更多相关《AWWA C900-2016 Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings 4 In Through 60 In (100 mm Through 1 500 mm).pdf（52页珍藏版）》请在麦多课文档分享上搜索。

1、AWWA Standard SM Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings, 4 In. Through 60 In. (100 mm Through 1,500 mm) Effective date: Aug. 1, 2016. First edition approved by AWWA Board of Directors June 8, 1975. This edition approved Jan. 16, 2015. Approved by American National Standards I

2、nstitute April 7, 2016 ANSI/AWWA C900-16 (Revision of ANSI/AWWA C900-07 and C905-10) Copyright 2016 American Water Works Association. All Rights Reserved.ii AWWA Standard This document is an American Water Works Association (AWWA) standard. It is not a specification. AWWA standards describe minimum

3、requirements and do not contain all of the engineering and administrative information normally contained in specifications. The AWWA standards usually contain options that must be evaluated by the user of the standard. Until each optional feature is specified by the user, the product or service is n

4、ot fully defined. AWWA pub- lication of a standard does not constitute endorsement of any product or product type, nor does AWWA test, certify, or approve any product. The use of AWWA standards is entirely voluntary. This standard does not supersede or take precedence over or displace any applicable

5、 law, regulation, or code of any governmental authority. AWWA standards are intended to represent a consensus of the water industry that the product described will provide satisfactory ser- vice. When AWWA revises or withdraws this standard, an official notice of action will be placed on the first p

6、age of the Official Notice section of Journal American Water Works Association. The action becomes effective on the first day of the month following the month of Journal American Water Works Association publication of the official notice. American National Standard An American National Standard impl

7、ies a consensus of those substantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether that per

8、son has ap - proved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standard. American National Standards are subject to periodic review, and users are cautioned to obtain the latest editions. Producers of goods made i

9、n conformity with an American National Standard are encour - aged to state on their own responsibility in advertising and promotional materials or on tags or labels that the goods are produced in conformity with particular American National Standards. Caution n oti Ce : The American National Standar

10、ds Institute (ANSI) approval date on the front cover of this standard indicates completion of the ANSI approval process. This American National Standard may be revised or withdrawn at any time. ANSI procedures require that action be taken to reaffirm, revise, or withdraw this standard no later than

11、five years from the date of publication. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute, 25 West 43rd Street, Fourth Floor, New York, NY 10036; 212.642.4900; or emailing infoansi.org. ISBN-13,

12、 print: 978-1-62576-175-0 eISBN-13, electronic: 978-1-61300-386-2DOI: http:/dx.doi.org/10.12999/AWWA.C900.16 All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy, recording, or any information or

13、retrieval system, except in the form of brief excerpts or quotations for review purposes, without the written permission of the publisher. Copyright 2016 by American Water Works Association Printed in USA hours of work by your fellow water professionals. Revenue from the sales of this AWWA material

14、supports ongoing product development. Unauthorized distribution, either electronic or photocopied, is illegal and hinders AWWAs mission to support the water community. This AWWA content is the product of thousands of Copyright 2016 American Water Works Association. All Rights Reserved.iii Committee

15、Personnel The Standard C900 Subcommittee that developed this standard had the following personnel at the time: Robert Walker, Chair L.M. Bowles, Bureau of Reclamation, Denver, Colo. (AWWA) B. Clark, JM Manufacturing Co. Inc., DBA JM Eagle, Los Angeles, Calif. (AWWA) D.L. Eckstein, EBAA Iron Sales In

16、c., Williamston, S.C. (AWWA) W. Fassler, Uni-Bell PVC Pipe Association, Ripon, Calif. (AWWA) C.A. Fisher, Star Pipe Products, North Richland Hills, Texas (AWWA) M. Glasgow, North American Pipe Corporation, Ashland City, Tenn. (AWWA) J.F. Houle, IPEX Inc., Mississauga, Ont., Canada (AWWA) M. Huynh, J

17、M Manufacturing Co. Inc., DBA JM Eagle, Los Angeles, Calif. (AWWA) K.S. Jeng-Bullock, City of Houston, Houston, Texas (AWWA) T.E. Layton, Orange County Utilities, Orlando, Fla. (AWWA) T. Marti, Underground Solutions Inc., Warrendale, Pa. (AWWA) S.K. Rajah, Bellevue, Wash. (AWWA) E.E. Schmidt, Diamon

18、d Plastics Corporation, Grand Island, Neb. (AWWA) G. Scoby, Palo Alto Utilities Department, Palo Alto, Calif. (AWWA) B. Sukolsky, Specified Fittings, Bellingham, Wash. (AWWA) R.P. Walker, Underground Solutions Inc., Southlake, Texas (AWWA) W.R. Whidden, Woolpert, Orlando, Fla. (AWWA) The AWWA Standa

19、rds Committee on Polyvinyl Chloride Pressure Pipe and Fittings, which re- viewed and approved this standard, had the following personnel at the time of approval: Bill Whidden, Chair Robert P. Walker, Vice-Chair General Interest Members J.P. Castronovo, Blue Ridge, Ga. (AWWA) A. Chastain-Howley,* Bla

20、ck manufacturing, testing, and inspection; pressure capacity; design factors for external forces; hydraulics; receiving, storage, and handling; testing and maintenance; and service connections (tapping). Recommended installation guidance is provided in ANSI/AWWA C605, Underground Installation of Pol

21、yvinyl Chloride (PVC) and Molecularly Oriented Polyvinyl Chloride (PVCO) Pressure Pipe and Fittings. I.B. History. In 1966, the American Water Works Association (AWWA) appointed Committee 8350-D to study and report on the adaptability of plastic pipe for use within the water industry. The committee

22、presented its report on June 6, 1967, at AWWAs annual conference. The report included a recommendation that a task group be appointed to prepare standards for the use of plastic materials. The AWWA Standards Committee on Thermoplastic Pressure Pipe Standards Committee was established in 1968. In Jun

23、e 1988, the Thermoplastic Pressure Pipe Committee was divided into two separate committees: the Polyvinyl Chloride Pressure Pipe and Fittings Standards Committee and the Polyolefin Pressure Pipe and Fittings Standards Committee. ANSI/AWWA C900 was the first thermoplastic pipe standard approved by th

24、e AWWA Board of Directors in June of 1975. This is the sixth edition of ANSI/AWWA C900. Previous revisions to ANSI/AWWA C900 were prepared by the AWWA Stan- dards Committee and approved in Jan. 1981, Jan. 1989, June 1997, and June 2007. This edition of ANSI/AWWA C900 was approved on Jan. 16, 2016. *

25、 American National Standards Institute, 25 West 43rd Street, Fourth Floor, New York, NY 10036. Copyright 2016 American Water Works Association. All Rights Reserved.viii I.C. Acceptance. In May 1985, the US Environmental Protection Agency (USEPA) entered into a cooperative agreement with a consortium

26、 led by NSF International (NSF) to develop voluntary third-party consensus standards and a certification program for direct and indirect drinking water additives. Other members of the original consortium included the Water Research Foundation (formerly AwwaRF) and the Conference of State Health and

27、Environmental Managers (COSHEM). The American Water Works Association (AWWA) and the Association of State Drinking Water Administrators (ASDWA) joined later. In the United States, authority to regulate products for use in, or in contact with, drinking water rests with individual states.* Local agenc

28、ies may choose to impose requirements more stringent than those required by the state. To evaluate the health effects of products and drinking water additives from such products, state and local agencies may use various references, including 1. An advisory program formerly administered by USEPA, Off

29、ice of Drinking Water, discontinued on Apr. 7, 1990. 2. Specific policies of the state or local agency. 3. Two standards developed under the direction of NSF : NSF/ANSI 60, Drinking Water Treatment ChemicalsHealth Effects, and NSF/ANSI 61, Drinking Water System ComponentsHealth Effects. 4. Other ref

30、erences, including AWWA standards, Food Chemicals Codex, Water Chemicals Codex, and other standards considered appropriate by the state or local agency. Various certification organizations may be involved in certifying products in accor- dance with NSF/ANSI 61. Individual states or local agencies ha

31、ve authority to accept or accredit certification organizations within their jurisdictions. Accreditation of certi- fication organizations may vary from jurisdiction to jurisdiction. Annex A, “Toxicology Review and Evaluation Procedures,” to NSF/ANSI 61 does not stipulate a maximum allowable level (M

32、AL) of a contaminant for substances not regulated by a USEPA final maximum contaminant level (MCL). The MALs of an unspecified list of “unregulated contaminants” are based on toxicity testing guidelines * Persons outside the United States should contact the appropriate authority having jurisdiction.

33、 NSF International, 789 North Dixboro Road, Ann Arbor, MI 48105. American National Standards Institute, 25 West 43rd Street, Fourth Floor, New York, NY 10036. Both publications available from National Academy of Sciences, 500 Fifth Street, NW, Washington, DC 20001. Copyright 2016 American Water Work

34、s Association. All Rights Reserved.ix (noncarcinogens) and risk characterization methodology (carcinogens). Use of Annex A procedures may not always be identical, depending on the certifier. ANSI/AWWA C900 does not address additives requirements. Thus, users of this standard should consult the appro

35、priate state or local agency having jurisdiction in order to 1. Determine additives requirements including applicable standards. 2. Determine the status of certifications by parties offering to certify products for contact with, or treatment of, drinking water. 3. Determine current information on pr

36、oduct certification. II. Special Issues. The pressure-class designation requirements and pressure design recommendations presented in this standard are different from those in AWWA Manual M23, PVC PipeDesign and Installation, second edition (2002). The requirements of this standard take precedence o

37、ver the design recommendations in AWWA Manual M23, second edition. Inconsistencies with AWWA M23 and this standard should be discussed with the manufacturer. The committee intends to revise the third edition of M23 to align with this standard. II.A. Selection of Pressure Class. The minimum pressure

38、class of the pipe selected should be equal to or greater than the system working pressure. The sum of the system working pressure and occasional surge pressure should not exceed 1.60 times the pressure class of the pipe. The system working pressure and recurring surge pressure should be analyzed usi

39、ng the method in Sec. 4.7. If surge pressures govern the selection of the pressure class, consideration should be given to removal of the cause of surge pressures or to the incorporation of surge suppressors in the system. II.B. Concern Regarding UV Light Effects. The effect of ultraviolet (UV) ligh

40、t on PVC pipe should be insignificant. User concerns such as outdoor storage should be discussed with the manufacturer. III. Use of This Standard. It is the responsibility of the user of an AWWA standard to determine that the products described in that standard are suitable for use in the particular

41、 application being considered. III.A. Purchaser Options and Alternatives. The following items should be provided by the purchaser: 1. Standard to be usedthat is, ANSI/AWWA C900, Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings, 4 In. Through 60 In. (100 mm Through 1,500 mm), of latest revision. 2. Whether compliance with NSF/ANSI 61, Drinking Water System ComponentsHealth Effects, is required. Copyright 2016 American Water Works Association. All Rights Reserved.