AWS B2 1-22-015-2011 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding of Aluminum (M P-22 to M P-22) 18 through 10 Gauge ER4043 or R4043 in the As-Welde.pdf

《AWS B2 1-22-015-2011 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding of Aluminum (M P-22 to M P-22) 18 through 10 Gauge ER4043 or R4043 in the As-Welde.pdf》由会员分享，可在线阅读，更多相关《AWS B2 1-22-015-2011 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding of Aluminum (M P-22 to M P-22) 18 through 10 Gauge ER4043 or R4043 in the As-Welde.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、AWS B2.1-22-015:2011An American National StandardStandard Welding ProcedureSpecification (SWPS) forGasTungsten ArcWelding of Aluminum(M/P-22 to M/P-22),18 through 10 Gauge,ER4043 or R4043, in theAs-Welded Condition,with or without BackingSite License550 N.W. LeJeune Road, Miami, FL 33126AWS B2.1-22-

2、015:2011An American National StandardApproved by theAmerican National Standards InstituteJuly 7, 2010Standard Welding Procedure Specification (SWPS) forGas Tungsten Arc Welding of Aluminum (M/P-22 toM/P-22), 18 through 10 Gauge, ER4043 or R4043, inthe As-Welded Condition, with or without Backing3rd

3、EditionSupersedes AWS B2.1-22-015:2002Prepared by theAmerican Welding Society (AWS) B2 Committee on Procedure and Performance QualificationUnder the Direction of theAWS Technical Activities CommitteeApproved by theAWS Board of DirectorsAbstractThis standard contains the essential welding variables f

4、or aluminum in the thickness range of 10 through 18 gauge usingmanual gas tungsten arc welding. It cites the base metals and operating conditions necessary to make the weldment, thefiller metal specifications, and the allowable joint designs for fillet welds and groove welds.AWS B2.1-22-015:2011Inte

5、rnational Standard Book Number: 978-0-87171-778-8American Welding Society550 N.W. LeJeune Road, Miami, FL 33126 2010 by American Welding SocietyAll rights reservedPrinted in the United States of AmericaiiAWS B2.1-22-015:2011Statement on the Use of American Welding Society StandardsAll standards (cod

6、es, specifications, recommended practices, methods, classifications, and guides) of the AmericanWelding Society (AWS) are voluntary consensus standards that have been developed in accordance with the rules of theAmerican National Standards Institute (ANSI). When AWS American National Standards are e

7、ither incorporated in, ormade part of, documents that are included in federal or state laws and regulations, or the regulations of other govern-mental bodies, their provisions carry the full legal authority of the statute. In such cases, any changes in those AWSstandards must be approved by the gove

8、rnmental body having statutory jurisdiction before they can become a part ofthose laws and regulations. In all cases, these standards carry the full legal authority of the contract or other documentthat invokes the AWS standards. Where this contractual relationship exists, changes in or deviations f

9、rom requirementsof an AWS standard must be by agreement between the contracting parties.AWS American National Standards are developed through a consensus standards development process that bringstogether volunteers representing varied viewpoints and interests to achieve consensus. While the AWS admi

10、nisters theprocess and establishes rules to promote fairness in the development of consensus, it does not independently test, evalu-ate, or verify the accuracy of any information or the soundness of any judgments contained in its standards.AWS disclaims liability for any injury to persons or to prop

11、erty, or other damages of any nature whatsoever, whetherspecial, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, or relianceon this standard. AWS also makes no guarantee or warranty as to the accuracy or completeness of any informationpublishe

12、d herein.In issuing and making this standard available, AWS is neither undertaking to render professional or other services for oron behalf of any person or entity, nor is AWS undertaking to perform any duty owed by any person or entity to someoneelse. Anyone using these documents should rely on his

13、 or her own independent judgment or, as appropriate, seek theadvice of a competent professional in determining the exercise of reasonable care in any given circumstances. It isassumed that the use of this standard and its provisions are entrusted to appropriately qualified and competent personnel.Th

14、is standard may be superseded by the issuance of new editions. Users should ensure that they have the latest edition.Publication of this standard does not authorize infringement of any patent or trade name. Users of this standard acceptany and all liabilities for infringement of any patent or trade

15、name items. AWS disclaims liability for the infringement ofany patent or product trade name resulting from the use of this standard.Finally, the AWS does not monitor, police, or enforce compliance with this standard, nor does it have the power to do so.On occasion, text, tables, or figures are print

16、ed incorrectly, constituting errata. Such errata, when discovered, are postedon the AWS web page (www.aws.org).Official interpretations of any of the technical requirements of this standard may only be obtained by sending a request, inwriting, to the appropriate technical committee. Such requests sh

17、ould be addressed to the American Welding Society,Attention: Managing Director, Technical Services Division, 550 N.W. LeJeune Road, Miami, FL 33126 (see Annex A).With regard to technical inquiries made concerning AWS standards, oral opinions on AWS standards may be rendered.These opinions are offere

18、d solely as a convenience to users of this standard, and they do not constitute professionaladvice. Such opinions represent only the personal opinions of the particular individuals giving them. These individuals donot speak on behalf of AWS, nor do these oral opinions constitute official or unoffici

19、al opinions or interpretations ofAWS. In addition, oral opinions are informal and should not be used as a substitute for an official interpretation.This standard is subject to revision at any time by the AWS B2 Committee on Procedure and Performance Qualification.It must be reviewed every five years

20、, and if not revised, it must be either reaffirmed or withdrawn. Comments (recom-mendations, additions, or deletions) and any pertinent data that may be of use in improving this standard are requiredand should be addressed to AWS Headquarters. Such comments will receive careful consideration by the

21、AWS B2Committee on Procedure and Performance Qualification and the author of the comments will be informed of the Com-mittees response to the comments. Guests are invited to attend all meetings of the AWS B2 Committee on Procedureand Performance Qualification to express their comments verbally. Proc

22、edures for appeal of an adverse decisionconcerning all such comments are provided in the Rules of Operation of the Technical Activities Committee. A copy ofthese Rules can be obtained from the American Welding Society, 550 N.W. LeJeune Road, Miami, FL 33126.iiiAWS B2.1-22-015:2011ivPersonnelAWS B2 C

23、ommittee on Procedure and Performance QualificationJ. J. Fluckiger, Chair Idaho National LaboratoryJ. L. Cooley, Vice Chair J. C. 1/8 through 3/4 in. Thick, PWHT Condition, Primarily PipeApplicationsB2.1-4-218 Standard Welding Procedure Specification (SWPS) for Shielded Metal Arc Welding ofChromium-

24、Molybdenum Steel (M-4/P-4, Group 1 or 2), E8018-B2, 1/8 through 1/2 in.Thick, As-Welded Condition; 1/8 through 1-1/2 in. Thick, PWHT Condition, Primarily PipeApplicationsB2.1-4-219 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding followedby Shielded Metal Arc Welding of C

25、hromium-Molybdenum Steel (M-4/P-4, Group 1 or 2), 1/8through 1/2 in. Thick, As-Welded Condition; 1/8 through 1-1/2 in. Thick, PWHT Condition,ER80S-B2 and E8018-B2, Primarily Pipe ApplicationsB2.1-4-220 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding (ConsumableInsert Roo

26、t) of Chromium-Molybdenum Steel (M-4/P-4, Group 1 or 2), E8018-B2, 1/8through 1/2 in. Thick, As-Welded Condition; 1/8 through 3/4 in. Thick, PWHT Condition,IN515 and ER80S-B2, Primarily Pipe ApplicationsB2.1-4-221 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding (Consumab

27、leInsert Root) followed by Shielded Metal Arc Welding of Chromium-Molybdenum Steel (M-4/P-4, Group 1 or 2), 1/8 through 1/2 in. Thick, As-Welded Condition; 1/8 through 1-1/2 in.Thick, PWHT Condition, IN515, ER80S-B2, and E8018-B2, Primarily Pipe ApplicationsB2.1-5A-222 Standard Welding Procedure Spe

28、cification (SWPS) for Gas Tungsten Arc Welding ofChromium-Molybdenum Steel (M-5A/P-5A), ER90S-B3, 1/8 through 1/2 in. Thick, As-WeldedCondition; 1/8 through 3/4 in. Thick, PWHT Condition, Primarily Pipe ApplicationsB2.1-5A-223 Standard Welding Procedure Specification (SWPS) for Shielded Metal Arc We

29、lding ofChromium-Molybdenum Steel (M-5A/P-5A), E9018-B3, 1/8 through 1/2 in. Thick, As-WeldedCondition; 1/8 through 1-1/2 in. Thick, PWHT Condition, Primarily Pipe ApplicationsB2.1-5A-224 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding followed byShielded Metal Arc Weldi

30、ng of Chromium-Molybdenum Steel (M-5A/P-5A), 1/8 through 1/2 in.Thick, As-Welded Condition; 1/8 through 1-1/2 in. Thick, PWHT Condition, ER90S-B3 andE9018-B3, Primarily Pipe ApplicationsB2.1-5A-225 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding (Consum-able Insert Root)

31、 of Chromium-Molybdenum Steel (M-5A/P-5A), 1/8 through 1/2 in. Thick,As-Welded Condition; 1/8 through 3/4 in. Thick, PWHT Condition, IN521 and ER90S-B3,Primarily Pipe ApplicationsDesignation TitleAWS B2.1-22-015:2011Page 13 of 13Permission to reproduce for intra-company use only is granted by the Am

32、erican Welding SocietyB2.1-5A-226 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding (ConsumableInsert Root) followed by Shielded Metal Arc Welding of Chromium-Molybdenum Steel (M-5A/P-5A), 1/8 through 1/2 in. Thick, As-Welded Condition; 1/8 through 1-1/2 in. Thick, PWHTCon

33、dition, IN521, ER90S-B3, and E9018-B3, Primarily Pipe ApplicationsB2.1-1/8-227 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding of CarbonSteel (M-1/P-1/S-1, Groups 1 or 2) to Austenitic Stainless Steel (M-8/P-8/S-8, Group 1), 1/16through 1-1/2 inch Thick, ER309(L), As-Wel

34、ded Condition, Primarily Pipe ApplicationsB2.1-1/8-228 Standard Welding Procedure Specification (SWPS) for Shielded Metal Arc Welding of Car-bon Steel (M-1/P-1/S-1, Groups 1 or 2) to Austenitic Stainless Steel (M-8/P-8/S-8, Group 1),1/8 through 1-1/2 inch Thick, E309(L)-15, -16, or -17, As-Welded Co

35、ndition, Primarily PipeApplicationsB2.1-1/8-229 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding followedby Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1, Groups 1 or 2) to AusteniticStainless Steel (M-8/P-8/S-8, Group 1), 1/8 through 1-1/2 inch Thick, ER309(L)

36、andE309(L)-15, -16, or -17, As-Welded Condition, Primarily Pipe ApplicationsB2.1-1/8-230 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding with Con-sumable Insert Root of Carbon Steel (M-1/P-1/S-1, Groups 1 or 2) to Austenitic StainlessSteel (M-8/P-8/S-8, Group 1), 1/16 th

37、rough 1-1/2 inch Thick, IN309 and ER309(L), As-WeldedCondition, Primarily Pipe ApplicationsB2.1-1/8-231 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding with Con-sumable Insert Root followed by Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1,Groups 1 or 2) to Aust

38、enitic Stainless Steel (M-8/P-8/S-8, Group 1), 1/8 through 1-1/2 inchThick, IN309, ER309, and E309-15, -16, or -17, or IN309, ER309(L), and ER309(L)-15, -16,or -17, As-Welded Condition, Primarily Pipe ApplicationsB2.1-1-232 Standard Welding Procedure Specification (SWPS) for Argon plus 25% Carbon Di

39、oxideShielded Gas Metal Arc Welding (Short Circuiting Transfer Mode) followed by Argon plus25% Carbon Dioxide Shielded Flux Cored Arc Welding of Carbon Steel (M-1/P-1/S-1, Groups1 and 2), 1/8 through 1-1/2 inch Thick, ER70S-3 and E7XT-X, As-Welded or PWHT Condition,Primarily Pipe ApplicationsB2.1-1-

40、233 Standard Welding Procedure Specification (SWPS) for Argon plus 25% Carbon DioxideShielded Gas Metal Arc Welding (Short Circuiting Transfer Mode) followed by Argon plus2% Oxygen Shielded Gas Metal Arc Welding (Spray Transfer Mode) of Carbon Steel (M-1/P-1/S-1, Groups 1 and 2), 1/8 through 1-1/2 i

41、nch Thick, ER70S-3, As-Welded or PWHT Condition,Primarily Pipe ApplicationsB2.1-1-234 Standard Welding Procedure Specification (SWPS) for Argon plus 25% Carbon DioxideShielded Flux Cored Arc Welding of Carbon Steel (M-1/P-1/S-1, Groups 1 and 2), 1/8through 1-1/2 inch Thick, E7XT-X, As-Welded or PWHT

42、 Condition, Primarily Pipe ApplicationsB2.1-1-235 Standard Welding Procedure Specification (SWPS) for Argon plus 2% Oxygen ShieldedGas Metal Arc Welding (Spray Transfer Mode) of Carbon Steel (M-1/P-1/S-1, Groups 1 and2), 1/8 through 1-1/2 inch Thick, ER70S-3, Flat Position Only, As-Welded or PWHTCondition, Primarily Pipe ApplicationsB2.2 Specification for Brazing Procedure and Performance QualificationB2.3 Specification for Soldering Procedure and Performance QualificationB2.4 Specification for Welding Procedure and Performance Qualification for Thermoplastics