ASTM G164-1999(2013) Standard Test Method for Determination of Surface Lubrication on Flexible Webs《测定挠性网状物表面润滑性的标准试验方法》.pdf

《ASTM G164-1999(2013) Standard Test Method for Determination of Surface Lubrication on Flexible Webs《测定挠性网状物表面润滑性的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM G164-1999(2013) Standard Test Method for Determination of Surface Lubrication on Flexible Webs《测定挠性网状物表面润滑性的标准试验方法》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: G164 99 (Reapproved 2013)Standard Test Method forDetermination of Surface Lubrication on Flexible Webs1This standard is issued under the fixed designation G164; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year

2、of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method has been used since 1988 as anANSI/ISO standard test for determination of lubrication onprocessed

3、photographic films. Its purpose was to determine thepresence of process-surviving lubricants on photographicfilms. It is the purpose of this test method to expand theapplicability of this test method to other flexible webs that mayneed lubrication for suitable performance. This test measuresthe brea

4、kaway (static) coefficient of friction of a metal rider onthe web by the inclined plane method. The objectives of the testis to determine if a web surface has a lubricant present or not.It is not intended to assign a friction coefficient to a material.It is not intended to rank lubricants.1.2 The va

5、lues stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate s

6、afety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ANSI/ISO Standards:2ANSI/ISO 5769-1984, ANSI/NAPM IT9.4-1992 forPhotography-Processed Films-Method for DeterminingLubrication3. Terminology3.1 Definitions:3.1.1 coeffcient of

7、 friction, , n, in tribologythe dimen-sionless ratio of the friction force (F) between two bodies to thenormal force (N) pressing these bodies together.3.1.2 friction force, nthe resisting force tangential to theinterface between two bodies when, under the action ofexternal force, one body moves or

8、tends to move relative to theother.3.1.3 lubricant, nany substance interposed between twosurfaces for the purpose of reducing the friction and wearbetween them.3.1.4 static coeffcient of friction, nthe coefficient offriction corresponding to the maximum friction force that mustbe overcome to initiat

9、e macroscopic motion between twobodies.3.1.5 triboelement, none of two or more solid bodieswhich comprise a sliding, rolling, or abrasive contact, or abody subjected to impingement or cavitation.3.1.6 tribology, nthe science and technology concernedwith interacting surfaces in relative motion, inclu

10、ding friction,lubrication, wear, and erosion.3.1.7 tribosystem, nany system that contains one or moretriboelements, including all mechanical, chemical, and envi-ronmental factors relevant to tribological behavior.4. Summary of Test Method4.1 This test method can be used to measure the frictioncharac

11、teristics of the surfaces of a flexible web sliding againstthe curved smooth surface of a paper clip.4.2 This test method is conducted on a narrow strip takenfrom a web of interest. The strip is affixed to an inclined planedevice with the surface of interest facing up. A paper clip isbalanced on the

12、 web surface with the inclined plane in thehorizontal position. The plane is then angled upward until therider breaks away.4.3 The angle at which breakaway occurred is recorded. Thetangent of that angle is the friction coefficient for that tribo-system.5. Significance and Use5.1 Many web materials d

13、o not convey satisfactorily inmanufacture or work, or both, as intended in service unlesstheir surface contains a very thin layer of lubricant in the formof a wax, particulate, thin film coating, or fluid. It is often veryexpensive and time consuming to use surface chemical analysistechniques to qua

14、ntify the presence of these films. A simplefriction test like this one performs this function.5.2 This test has been used for over twenty years to detectthe presence of lubricants on the surface of photographic filmsat various stages in manufacture. In this instance the surfaces1This test method is

15、under the jurisdiction of ASTM Committee G02 on Wearand Erosion and is the direct responsibility of Subcommittee G02.50 on Friction.Current edition approved Nov. 15, 2013. Published November 2013. Originallyapproved in 1999. Last previous edition approved in 2009 as G16499(2009). DOI:10.1520/G0164-9

16、9R13.2Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1are lubricated with waxes and this test reliably detec

17、ts if thewax is present. It is not used to quantify the amount of wax,only if it is present. This test can be used as a quality test tomake sure that a lubricant is present. Test samples are normallycompared with an unlubricated reference specimen. The coef-ficient of friction of the test samples is

18、 compared with thecoefficient of friction of the unlubricated reference specimensto determine if a lubricant is present.6. Apparatus6.1 Friction SliderThe rider in this friction test is aU-shaped device with a paper clip inserted in the center. Thisrider slides on the test web that is attached to th

19、e inclinedplane. The material of construction is not important, but thecenter of gravity shall be at least 25 mm below the end of thepaper clip. Acrylic sheet has been determined to be a suitablematerial of construction. The paper clip must be uncoated steeland have a smooth (as opposed to serrated

20、or dull) finish. Theoverall dimensions of suitable paper clips are between 5 and 8mm wide and between 25 and 35 mm long. The wire diametershould be in the range of 0.6 to 0.75 mm. The mass of the slidershould be in the range of 50 to 100 g.6.2 Inclined PlaneThe dimensions and typical construc-tion o

21、f the inclined plane test rig are shown in Fig. 1. Theessential requirements of the inclined plane are:6.2.1 The surface of the inclined plane should be smooth(0.2 m Ra surface roughness) rigid and not deformableunder test conditions. Acrylic sheet has been determined to bean acceptable surface.6.2.

22、2 It shall be narrow and high enough to accommodateunobstructed slider motion.6.2.3 It shall have a device for test material attachment or itshall have sufficient room to allow attachment with two-sidedpressure sensitive adhesive.6.2.4 It shall be capable of being raised and lowered withsmooth unint

23、errupted motion and it shall have a means ofclamping the plane at the angle at which rider breakawayoccurs.6.3 Angle MeasurementThe test metric is the angle incli-nation of the inclined plane () when rider motion occurs. Thisangle can be measured by a protractor or by calibration of agage on the dev

24、ice. A suitable device for angle measurement isan electronic level. These devices present a digital anglereadout to two places. The devices reputedly are accurate to60.1. The least count on the angle-measuring protractor shallbe 1.7. Test Procedure7.1 Sample PreparationTest samples shall be the thic

25、k-ness of the test material with a width between 25 and 35 mmand a length of at least 150 mm. Take care to not contaminatethe test with fingerprints or other material that is not normallyfound on the test surface. Outer convolutions of web rolls areoften contaminated by operators holding the film ti

26、ght whilethe roll is taped. Do not use outer convolutions for testing.7.2 Test MaterialsAny material that will lay flat on theinclined plane may be tested, but the test was developed for theflexible webs used to make photographic film. Do not use thistest for sandpaper and the like that will damage

27、the papercliprider during the test.7.3 Test ConditionsConduct tests with relative humiditybetween 35 and 55 % and at a temperature of 20 6 5C.Condition samples for 24 h in the test atmosphere prior totesting.7.4 Mounting the WebMount the test web with a clamp oradhere it in such a manner that it is

28、flat to the inclined planewith no wrinkles or bows. If the sample is taped to the inclinedplane, do not put the tape in the test area.7.5 Conducting the TestClamp the test rig to a levelhorizontal surface. Raise the sample plane to an arbitraryangle; place the rider (paper-clip) on the inclined plan

29、e so thatonly the paper clip touches the test surface. If the rider slidesdown the plane, lower the plane and repeat placement of therider on the test surface. If the rider still freely slides repeat theprocedure until the rider no longer moves on the inclined plane.Repeat this operation until the m

30、aximum angle is determined(to the precision desired) at which point the rider fails to slide.7.5.1 Repeat the procedure twice more on a different area ofthe test sample. Calculate the arithmetic average of the threeangle determinations. Take the tangent of the average and thisis the test result, a u

31、nitless static coefficient of friction for apaperclip/film tribosystem.s5 tan avg of 3 determinations(1)8. Report8.1 Test DataThe following values shall be recorded:8.1.1 The name and number of the test sample,8.1.2 Identify the test surface,8.1.3 The average friction coefficient(s) of the surface(s

32、)tested,8.1.4 The number of samples tested, and8.1.5 The temperature and relative humidity of the test.8.2 Interpretation of ResultsTotally unlubricated cellulosetriacetate films generally produce static friction coefficients inFIG. 1 ApparatusG164 99 (2013)2excess of 0.4. Effective lubricants, well

33、 applied, will generallyproduce static coefficients of friction of 0.15 or lower. Howeverthe presence of lubrication can only be determined withcertainty if the paper clip test is conducted on a control samplewith known lubrication. This test is intended to identifysurfaces that are supposed to be l

34、ubricated and are not, or ifthey are improperly lubricated.9. Precision and Bias9.1 PrecisionThe test variability in interlaboratory testson three lubricated (carnauba wax) and unlubricated plasticwebs is shown in Table 1. The research report includes agraphical presentation of all of the test resul

35、ts.39.1.1 The within-laboratory variation was essentially 10 %or less; the between-laboratory variation was in the range of 17to 27 %.9.2 BiasThere is no absolute value of a friction coeffi-cient. It is a product of a particular tribosystem. Therefore, thevalue can have no bias. Some of the factors

36、in this test methodthat can cause reproducibility and repeatability problems are asfollows:9.2.1 Contamination of the test surfaces,9.2.2 A burr or nick on the rider,9.2.3 Irregular motion (jerking) in raising or lowering theplane,9.2.4 Temperature or humidity differences,9.2.5 A buckle or bubble of

37、 the web in the path of the rider,and9.2.6 Air currents directed on the rider.10. Keywords10.1 friction testing; photographic films; plastic sheet; staticcoefficient of friction; websASTM International takes no position respecting the validity of any patent rights asserted in connection with any ite

38、m mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical comm

39、ittee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a m

40、eeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive

41、, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org

42、). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).3Supporting data have been filed at ASTM International Headquarters and maybe obtained by requesting Research Report RR:G02-1011.TABLE 1 Interlaboratory Test Data-Statistical Analysis S

43、ummaryNOTE 1The within-laboratory coefficient of variation ranged from 5 to 10.6 %; between laboratory ranged from 16.9 to 27.7 %.Interlatoratory Friction Measurements (s)Between LaboratoryTest Surface Laboratory 1 Laboratory 2 Laboratory 3 Laboratory 4 Laboratory 5 Average Standard DeviationPVC 0.54 0.44 0.7 0.61 0.59 0.587 0.097PVC plus wax 0.18 0.12 0.24 0.26 0.35 0.23 0.064Pet 0.13 0.27 0.31 0.33 0.27 0.26 0.075Pet plus wax 0.09 0.06 0.12 0.12 0.11 0.1 0.024PTFE 0.07 0.08 0.14 0.1 0.14 0.1 0.029PTFE plus wax 0.05 0.05 0.09 0.1 0.09 0.076 0.024G164 99 (2013)3