ASTM F3012-2014 Standard Specification for Loose-Fill Rubber for Use as a Playground Safety Surface under and around Playground Equipment《作为游乐场设备下方及周围游乐场安全表面使用松散填充橡胶的标准规范》.pdf
《ASTM F3012-2014 Standard Specification for Loose-Fill Rubber for Use as a Playground Safety Surface under and around Playground Equipment《作为游乐场设备下方及周围游乐场安全表面使用松散填充橡胶的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM F3012-2014 Standard Specification for Loose-Fill Rubber for Use as a Playground Safety Surface under and around Playground Equipment《作为游乐场设备下方及周围游乐场安全表面使用松散填充橡胶的标准规范》.pdf(9页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F3012 14Standard Specification forLoose-Fill Rubber for Use as a Playground Safety Surfaceunder and around Playground Equipment1This standard is issued under the fixed designation F3012; the number immediately following the designation indicates the year oforiginal adoption or, in the c
2、ase of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONRecycled rubber used in loose-fill applications is found in a wide variety of products, i
3、ncludinglandscaping mulch, equestrian surfacing, artificial turf in-fill, and resilient playground surfacing. Thegoal of this specification is to provide test methods and performance requirements for loose-fill rubberplayground-surfacing products. It is intended to complement existing ASTM Internati
4、onal standardsfor determining the shock attenuation and accessibility of a playground surface. This specification willassist playground designers and specifiers, owner/operators, and playground-surfacing suppliers inevaluating loose-fill rubber products for playground use.1. Scope1.1 This specificat
5、ion establishes test methods and perfor-mance requirements for particle size distribution, extractablehazardous metal content, total lead content, tramp metalcontent, and sharp tramp metal content for loose-fill rubber thatis intended to be used as a playground surface.1.2 This specification does no
6、t contain test methods orperformance requirements for the accessibility of loose-fillrubber playground surfacing. The specification also does notestablish test methods or performance requirements to charac-terize the release of organic chemicals from loose-fill rubberintended to be used as a playgro
7、und surface. Appendix X1 andAppendix X2 contain additional information on these topics.1.3 If loose-fill rubber which meets the requirements of thisstandard is to be installed in the use zone of playgroundequipment, it must also comply with Specification F1292.1.4 The values stated in inch-pound uni
8、ts are to be regardedas the standard.The values given in parentheses are mathemati-cal conversions to SI units that are provided for informationonly and are not considered standard.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresp
9、onsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C136 Test Method for Sieve Analysis of Fine and CoarseAggregatesD1193 Specification for Rea
10、gent WaterE11 Specification for Woven Wire Test Sieve Cloth and TestSievesE1613 Test Method for Determination of Lead by Induc-tively Coupled Plasma Atomic Emission Spectrometry(ICP-AES), Flame Atomic Absorption Spectrometry(FAAS), or Graphite Furnace Atomic Absorption Spec-trometry (GFAAS) Techniqu
11、esF963 Consumer Safety Specification for Toy SafetyF1292 Specification for Impact Attenuation of SurfacingMaterials Within the Use Zone of Playground Equipment2.2 U.S. EPA Standards and Methods:3EPA Method 3050B Acid Digestion of Sediments, Sludgesand Soils; SW 846, Test Methods for Evaluating Solid
12、Waste, Physical/Chemical MethodsEPA Method 3051A Microwave Assisted Acid Digestion ofSediments, Sludges and Soils; SW 846, Test Methods forEvaluating Solid Waste, Physical/Chemical MethodsEPA Method 6010B Inductively Coupled Plasma-AtomicEmission Spectrometry; SW 846, Test Methods for Evalu-ating So
13、lid Waste, Physical/Chemical Methods1This specification is under the jurisdiction of ASTM Committee F08 on SportsEquipment, Playing Surfaces, and Facilities and is the direct responsibility ofSubcommittee F08.63 on Playground Surfacing Systems.Current edition approved May 1, 2014. Published May 2014
14、. DOI: 10.1520/F3012-14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from the U.S. EPA, Office
15、of Resource Conservation and Recovery,(5305P), 1200 Pennsylvania Ave., N.W., Washington, DC 20460.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1EPA Method 7470A Mercury in Liquid Waste (ManualCold-Vapor Technique); SW 846, Test Meth
16、ods for Evalu-ating Solid Waste, Physical/Chemical Methods2.3 Federal Standards:416 CFR 1500.48 Technical Requirements for Determining aSharp Point in Toys and Other Articles Intended for Useby Children Under 8 Years of Age3. Terminology3.1 Definitions:3.1.1 hazardous metal, nmetal that could have t
17、he poten-tial to cause harm to humans3.1.2 organic chemical, nchemical compound containingcarbon and hydrogen.3.1.3 particle size distribution, nlist of values that definesthe relative amounts of particles present in a mixture.3.1.4 sieve analysis, nprocedure used to determine theparticle size distr
18、ibution of a granular material.3.1.5 tramp metal, nunwanted metal that finds its way intoloose-fill rubber, generally steel.3.1.6 use zone, narea beneath and immediately adjacent toa play structure or playground equipment that is designated forunrestricted circulation around the equipment and on who
19、sesurface it is predicted that a user would land when falling fromor exiting the equipment.3.2 Definitions of Terms Specific to This Standard:3.2.1 buffng, rubber, nelongated rubber strand.3.2.1.1 DiscussionThe approximate dimensions (0.039 to0.375 inches thick (1 to 9.5 mm), 0.039 to 0.50 in. (1 to
20、 12.7mm) wide, 0.079 to 3.0 in. (2 to 76.2 mm) long) of buffingsused in loose-fill rubber playground surfacing differ from thoseof buffings used in poured-in-place rubber playground surfac-ing.3.2.2 loose-fill rubber, nrubber particles in the form ofnuggets or buffings.3.2.3 nugget, rubber, nrubber
21、granule, irregular in shape,with maximum dimension of approximately38 to78 in. (9.5 to22.2 mm).4. Performance Requiremetns4.1 Loose-fill rubber represented as complying with thisspecification shall meet all applicable requirements specifiedherein.Anyone representing compliance with this specificatio
22、nshall keep such records as are necessary to document any claimthat the requirements within this specification have been met.4.2 Sieve Analysis:4.2.1 NuggetsWhen a sample of loose-fill rubber in theform of nuggets is tested in accordance with Section 7, theminimum and maximum passing through the two
23、 sieves shallbe as in Table 1.4.2.2 BuffngsWhen a sample of loose-fill rubber in theform of buffings is tested in accordance with Section 7, theminimum and maximum passing through four sieves shall beas in Table 2.4.3 Hazardous Metal ContentWhen the sample is ana-lyzed using the procedure described
24、in Section 8 (including thecorrection for statistical errors as described in 8.4.6), themaximum content of hazardous metals shall not exceed theconcentrations shown in Table 3.4.4 Tramp Metal ContentWhen tested in accordance withthe procedure described in Section 9, there shall be no trampmetal part
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF30122014STANDARDSPECIFICATIONFORLOOSEFILLRUBBERFORUSEASAPLAYGROUNDSAFETYSURFACEUNDERANDAROUNDPLAYGROUNDEQUIPMENT

链接地址:http://www.mydoc123.com/p-539899.html