ASTM F2919 F2919M-2012(2018) Standard Specification for Welded Wire Mesh Fence Fabric (Metallic-Coated or Polymer Coated) with Variable Mesh Patterns or Meshes Greater than 6 in 2 .pdf

《ASTM F2919 F2919M-2012(2018) Standard Specification for Welded Wire Mesh Fence Fabric (Metallic-Coated or Polymer Coated) with Variable Mesh Patterns or Meshes Greater than 6 in 2 .pdf》由会员分享，可在线阅读，更多相关《ASTM F2919 F2919M-2012(2018) Standard Specification for Welded Wire Mesh Fence Fabric (Metallic-Coated or Polymer Coated) with Variable Mesh Patterns or Meshes Greater than 6 in 2 .pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F2919/F2919M 12 (Reapproved 2018)Standard Specification forWelded Wire Mesh Fence Fabric (Metallic-Coated or PolymerCoated) with Variable Mesh Patterns or Meshes Greater than6 in.23871 mm2 in Panels1This standard is issued under the fixed designation F2919/F2919M; the number immediately

2、 following the designation indicates the yearof original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specif

3、ication covers welded wire mesh fence fabricproduced from steel wire or metallic-coated steel wire. Themetallic-coated fabric may be polymer coated after fabrication.1.2 Welded wire mesh fence fabric is produced in fourtypes, based on the kind of coating, as described in Section 4.1.3 This specifica

4、tion is applicable to orders in eitherinch-pound units or SI units. Values stated in either inch-poundor SI units are to be regarded separately as the standard. Withinthe text, the SI units are shown in brackets. The values in thetwo systems are not exact equivalents; therefore, each systemshall be

5、used independent of the other, without combiningvalues in any way.1.4 This specification references notes and footnotes, whichprovide explanatory material. These notes and footnotes (ex-cluding those in tables and figures) shall not be considered asrequirements of this specification.1.5 The followin

6、g safety hazards caveat pertains only to thetest methods portion, 13.4, of this specification: This standarddoes not purport to address all of the safety concerns, if any,associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety, health, and enviro

7、n-mental practices and determine the applicability of regulatorylimitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards

8、, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2A82/A82M Specification for Steel Wire, Plain, for ConcreteReinforcement (Withdrawn 2013)3A90/A90M Test Method for Weight Mass of Coating onIron a

9、nd Steel Articles with Zinc or Zinc-Alloy CoatingsA123/A123M Specification for Zinc (Hot-Dip Galvanized)Coatings on Iron and Steel ProductsA185/A185M Specification for Steel Welded WireReinforcement, Plain, for Concrete (Withdrawn 2013)3A641/A641M Specification for ZincCoated (Galvanized)Carbon Stee

10、l WireA853 Specification for Steel Wire, Carbon, for General UseA856/A856M Specification for Zinc-5 % Aluminum-Mischmetal Alloy-Coated Carbon Steel WireA902 Terminology Relating to Metallic Coated Steel Prod-uctsA1064/A1064M Specification for Carbon-Steel Wire andWelded Wire Reinforcement, Plain and

11、 Deformed, forConcreteB117 Practice for Operating Salt Spray (Fog) ApparatusD1499 Practice for Filtered Open-Flame Carbon-Arc Expo-sures of PlasticsF934 Specification for Standard Colors for Polymer-CoatedChain Link Fence Materials2.2 ISO Standard:ISO 2178 Non-Magnetic Coatings on MagneticSubstrates

12、Measurement of Coating ThicknessMagnetic41This specification is under the jurisdiction of ASTM Committee F14 on Fencesand is the direct responsibility of Subcommittee F14.35 on Architectural MetalFence Systems.Current edition approved March 1, 2018. Published March 2018. Originallyapproved in 2012.

13、Last previous edition approved in 2012 as F2919/F2919M12.DOI:10.1520/F2919_F2919M-12R18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summa

14、ry page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C7

15、00, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the W

16、orld Trade Organization Technical Barriers to Trade (TBT) Committee.13. Terminology3.1 DefinitionsRefer to Terminology A902 for generalterminology relating to metallic-coated steel products.3.2 Definitions of Terms Specific to This Standard:3.2.1 welded wire mesh fence fabricmaterial composed ofa se

17、ries of longitudinal and transverse steel wires arrangedsubstantially at right angles to each other, and welded togetherat the points of intersection by electrical resistance welding toform fabricated panels.NOTE 1See Tables 1-3 for a list of typical standard mesh sizes. Thislist does not cover all

18、options that may be available.3.2.2 wirereferred to as plain wire and welded plain wireused in the fabrication of the fence panels.4. Classification4.1 Welded wire mesh fence fabric is classified according tocoating as follows:4.1.1 Type 1, consists of welded wire fabric made from wirewhich is zinc-

19、coated, in accordance with A641/A641M, Class3 minimum, before being welded into fabric, known asgalvanized before welding.4.1.2 Type 2, consists of welded wire fabric which is madefrom uncoated wire and the fabric is subsequently zinc-coatedafter fabrication, in accordance with Specification A123/A1

20、23M, Coating Grade 35, known as galvanized after welding.4.1.3 Type 3, consists of welded wire fabric made from wirewhich is coated with zinc-5 % aluminum mischmetal alloy(Zn-5Al-MM), in accordance with Specification A856/A856M, before being welded into fabric, known as zinc 5 %aluminum mischmetal a

21、lloy-coated steel before welding.4.1.4 Type 4, consists of welded wire fabric made from wirewhich is zinc-coated, in accordance with Specification A641/A641M, 0.3 oz/ft2minimum, before being welded into fabric,known as galvanized before welding, and subsequently poly-mer coated.4.1.5 In agreement be

22、tween buyer and supplier Types 1, 2,3, or 4 can be subsequently polymer coated to produce polymercoated welded wire fabric.4.2 Welded wire mesh fence fabric is classified in accor-dance with the method of fabrication, as follows:4.2.1 Model A: Panels fabricated with single wires inhorizontal and ver

23、tical direction. With horizontal reinforcingfolds (beams). (See Table 1 and Fig. 1).4.2.2 Model B: Panels fabricated with two horizontal wireswith a vertical wire placed between them. (See Table 2 and Fig.1).4.2.3 Model C: Panels fabricated with single wires inhorizontal and vertical directionflat i

24、n structure. (See Table 3and Fig. 1).4.2.4 Models A and B: Panels may be bent along the lengthto form a bent section at 45 degrees. (See Fig. 2).4.2.5 All panels have to be fabricated so that they do notexceed 4 in. on centers in one dimension (length, width, orheight) so they meet the maximum permi

25、tted dimensionbetween wires in one direction which is 4 in. on centers.4.2.6 All panels have to fabricated from wire with aminimum diameter of 9.0 gage (0.148 in. 3.76 mm metalliccoated core.5. Ordering Information5.1 Orders for material purchased under this specificationshall include the following

26、information:5.1.1 Quantity (number of panels).5.1.2 Mesh Description: Mesh spacing(s) and wire sizes(gages) in metallic core diameter for polymer coated panels.5.1.3 Panel size (height by width).5.1.4 Type of coating (Section 4), including the specific typeto be furnished.5.1.5 ASTM designation and

27、year of issue.5.1.6 Any special requirements (see Section 8).5.1.7 Certification, if required (see 15.1).NOTE 2A typical ordering description, with single wires in verticaland horizontal direction, would be as follows: 500 panels Model A: 6 in.by 2 in. mesh by 6 gage horizontal and vertical wires, t

28、hen height by width(length) conforming to F2919-XX. Where single wires with different gagein vertical and horizontal direction, then as follows: 500 panels Model A:6 in by 2 in. mesh by 4 gage horizontal and 6 gage vertical wires; thenheight by width (length) conforming to F2919-XX. Where panels wit

29、hdouble horizontal wires are required it would be: 500 panels Model B: 8in. by 2 in. mesh, 2 by 0 gage horizontal wires with 4 gage vertical wireswelded between them conforming to F2919-XX. Where panels withvariable openings in height are required, it would be: 500 panels Model C:Variable mesh by 3.

30、5 in. clear mesh, 4 gage horizontal, and 7 gage verticalwires conforming to F2919-XX. In each case the vertical mesh opening(height measured from top to bottom) is designated first, followed by thehorizontal mesh opening (width measured from left to right).6. Material and Manufacture6.1 The wire use

31、d in the manufacture of welded wire meshfence fabric shall conform to the specifications in 6.1.1 asTABLE 1 Panel Sizes Model ASingle wire in each direction with horizontal reinforcing folds (or beams). (See Fig. 1, Model A)NOTE 1These are examplesOther meshes and wire diameters are available. These

32、 are acceptable providing they meet all the requirements of thisASTM specification and are acceptable to the purchaser and client. Not all panels have horizontal reinforcing folds (beams) as shown in Fig. 1, ModelA, if mounted within a frame.VerticalWireSpacing(nominal)HorizontalWireSpacing(nominal)

33、AWire Diameter(Metallic-coated core: nominal)Panel HeightVertical Horizontalin. mm in. mm Gage in. mm Gage in. mm in. (approx.) mm (approx.)2 50 6 150 6.0 0.192 4.88 6.0 0.192 4.88 48607296 12001500180024002 50 4 100 7.0 0.177 4.50 7.0 0.177 4.50 4248607284 105012001500180021002 50 8 200 5.75 0.196

34、4.98 5.75 0.196 4.98 424860728496 1050120015001800210024002 50 8 200 6.25 0.188 4.80 6.25 0.189 4.80 39607896 1000150020002400AWhere panels have horizontal folds (beams) small spacing of horizontal wires may apply.F2919/F2919M 12 (2018)2appropriate for the type ordered, except the tensile strengthsh

35、all conform to 7.1. The wire may be produced from anygrade of steel listed in Specification A1064/A1064M or A853.6.1.1 Type 1 welded wire fabric shall be manufactured fromzinc-coated steel wire conforming to Specification A641/A641M, Class 3 coating (minimum). Type 2 welded wirefabric shall be manuf

36、actured from uncoated steel wire con-forming to Specification A82/A82M or A853, and the fabricsubsequently zinc-coated by the hot-dip process, confirming toSpecification A123/A123M, Coating Grade 35 (minimum).Type 3 welded wire fabric shall be manufactured from zinc-5 % aluminum-mischmetal coated st

37、eel wire conforming toSpecification A856/A856M, Class 80 coating (minimum).Type 4 welded wire fabric shall be manufactured from zinc-coated steel wire conforming to Specification A641/A641M0.3 oz/ft2, minimum weight coat.TABLE 2 Panel Sizes Model BSingle vertical wire. Double horizontal wire. (See F

38、ig. 1, Model B)NOTE 1These are examplesOther meshes and wire diameters are available. These are acceptable providing they meet all the requirements of thisASTM specification and are acceptable by the purchaser and client.VerticalWireSpacing(nominal)HorizontalWiresSpacing(nominal)Wire Diameter(Metall

39、ic-coated core: nominal)Panel HeightVerticalOne (1) WireHorizontalTwo (2) Wirein. mm in. mm Gage in. mm Gage in. mm in. (approx.) mm (approx.)2 50 8 200 4.0 0.225 5.72 4.0 0.225 5.72 487296 1200180024002 50 8 200 4.0 0.225 5.72 0.0 0.303 7.70 487296 1200180024002 50 8 200 5.75 0.196 4.98 3.5 0.236 6

40、.00 424854667284 1000120014501650180020002 50 8 200 3.5 0.236 6.00 00.75 0.315 8.00 424854667296 100012001450165018002400TABLE 3 Panel Sizes Model CSingle wire in each direction. Flat construction and variable wire spacing in panel height. (See Fig. 1,Model C)NOTE 1These are examplesOther meshes and

41、 wire diameters are available. These are acceptable providing they meet all the requirements of thisASTM specification and are acceptable by the purchaser and client.VerticalWireClear MeshSpacing(nominal)HorizontalWireSpacing(nominal)Wire Diameter(Metallic-coated core: nominal)Panel HeightVertical H

42、orizontalin. mm in. mm Gage in. mm Gage in. mm in. (approx.) mm (approx.)1.75 45 Variable 9.0 0.148 3.77 9.0 0.148 3.77 486072 1200150018001.75 45 Variable 6.0 0.192 4.88 6.0 0.192 4.88 486072 1200150018003.50 45 Variable 4.0 0.255 5.72 6.0 0.192 4.88 486072 1200150018003.50 45 Variable 2.0 0.262 6.

43、67 6.0 0.192 4.88 486072 120015001800NOTE 1Model A panels normally have horizontal reinforcing folds (or beams) to increase horizontal rigidity. Number of folds (beams) increase withthe height of the panel. Generally two folds for panels shorter than 5 ft 1525 mm, three folds if shorter than 6 ft 6

44、in. 1980 mm and four folds fortaller panels up to 8 ft 2430 mm.NOTE 2Model B panels have vertical wires sandwiched between two (2) horizontal wires.NOTE 3Model C panels have straight wire in both directions. Panels have variable wire spacing in panel height.FIG. 1 Examples of Model A, B, and C Panel

45、sF2919/F2919M 12 (2018)36.2 Wire for welded wire mesh fence fabric shall beassembled by automatic machines or other suitable mechanicalmeans that will ensure accurate spacing and alignment of allmembers of the finished fabric. Longitudinal and transversemembers of the welded wire fabric shall be con

46、nected at everyintersection in accordance with the requirements of 13.4 by theprocess of electric resistance welding, which employs theprinciple of fusion combined with pressure.6.3 Horizontal reinforcing folds (beams) may be incorpo-rated into Model A panels. Sufficient folds (beams) shall beincorp

47、orated in the panel to ensure straightness and lessflexibility, if panel is not used within frame. (See recommen-dation table in Fig. 1).6.4 Model C type panels should be fitted to steel frameworkto ensure rigidity in the panel length (width).6.5 The polymer coating used in the manufacture ofpolymer

48、-coated welded wire mesh fence fabric shall conformto the properties in 8.2 and 8.3.6.5.1 The polymer coated welded wire mesh fence fabricshall have the polymer coating fused and adhered onto themetallic-coated welded wire fabric after fabrication of themesh.7. Mechanical Properties7.1 Tensile Stren

49、gthThe tensile strength of the wire usedfor the welded wire mesh fence fabric shall be soft, medium orhard in accordance with the requirement of SpecificationsA641/A641M (Type 1 and 4), A856/A856M (Type 3) and harddrawn in accordance with Specification A82/A82M or A853(Type 2). The cross-sectional area of the test wire specimenshall be based on the diameter of the