ASTM F2599-2006 Standard Practice for The Sectional Repair of Damaged Pipe By Means of An Inverted Cured-In-Place Liner《借助反向现场固化衬套的损坏管部分修理标准实施规程》.pdf

《ASTM F2599-2006 Standard Practice for The Sectional Repair of Damaged Pipe By Means of An Inverted Cured-In-Place Liner《借助反向现场固化衬套的损坏管部分修理标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2599-2006 Standard Practice for The Sectional Repair of Damaged Pipe By Means of An Inverted Cured-In-Place Liner《借助反向现场固化衬套的损坏管部分修理标准实施规程》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 2599 06Standard Practice forThe Sectional Repair of Damaged Pipe By Means of AnInverted Cured-In-Place Liner1, 2This standard is issued under the fixed designation F 2599; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revisi

2、on, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers requirements and test methods forthe sectional cured-in-place lining (SCIPL) rep

3、air of a pipe line(4 in, through 60 in. ) by the installation of a continuousresin-impregnated-textile tube into an existing pipe by meansof air or water inversion and inflation. The tube is pressedagainst the host pipe by air or water pressure and held in placeuntil the thermo set resins have cured

4、. When cured, thesectional liner shall extend over a predetermined length of thehost pipe as a continuous, one piece, tight fitting, corrosionresistant and verifiable non-leaking cured-in-place pipe.1.2 The values stated in inch-pound units are to be regardedas the standard.The values given in paren

5、theses are mathemati-cal conversions to SI units that provided for information onlyand are not considered standard.1.3 There is no similar or equivalent ISO Standard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of t

6、he user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. Particular attentionis drawn to those safety regulations and requirements involvingentering into and working in confined spaces.2. Referenced Docume

7、nts2.1 ASTM Standards:3D 790 Test Methods for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating MaterialsD 1600 Terminology for Abbreviated Terms Relating toPlasticsD 3681 Test Method for Chemical Resistance of “Fiber-glass” (GlassFiberReinforced Thermosetting-Resi

8、n)Pipe in a Deflected ConditionD 5813 Specification for Cured-In-Place ThermosettingResin Sewer Piping SystemsF 412 Terminology Relating to Plastic Piping SystemsF 1216 Practice for Rehabilitation of Existing Pipelines andConduits by the Inversion and Curing of a Resin-Impregnated Tube,2.2 NASSCO Gu

9、idelines:4Recommended Specifications for Sewer Collection SystemRehabilitation.3. Terminology3.1 Definitions:3.1.1 Unless otherwise indicated, definitions are in accor-dance with Terminology F 412, and abbreviations are inaccordance with Terminology D 1600.3.2 Definitions of Terms Specific to This S

10、tandard:3.2.1 access point, nupstream or downstream manholes,that serve as the point of entrance or exit for the liner assemblyinto the existing pipe.3.2.2 bladder, na translucent plastic apparatus that whenpressurized, causes the tube to be inverted through the dam-aged pipe section and pressed aga

11、inst the pipe walls. Thebladder joined with the tube creates a liner/bladder assembly.3.2.3 frangible connection, na joining or combining oftwo objects that can be easily disconnected or separated bymeans of force.3.2.4 inversion, nthe process of turning the resin-impregnated tube inside out by the

12、use of air or water pressure.3.2.5 launcher, nan elongated flexible pressure vessel(hose apparatus) with one open end and one closed end capableof receiving air pressure to cause a liner/bladder assembly toinvert forward out from the launcher.3.2.6 lift, na portion of the cured liner that has cured

13、in aposition such that it has pulled away from the existing pipewall.3.2.7 liner/bladder assembly, na combination of a tubeand bladder that are frangibley connected.1This practice is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommitte

14、e F17.67 onTrenchless Plastic Pipeline Technology.Current edition approved Aug. 15, 2006. Published August 2006.2The sectional repair of damaged pipe by means of inversion of a cured in placeliner is covered by patents (LMK Enterprises, Inc. 1779 Chessie Lane, Ottawa, IL61350). Interested parties ar

15、e invited to submit information regarding the identifi-cation of acceptable alternatives to this patented item to the Committee onStandards, ASTM Headquarters, 100 Barr Harbor Drive, West Conshohocken, PA19428-2959. Your comments will receive careful consideration at a meeting of theresponsible tech

16、nical committee which you may attend.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4NASSCO, 1314 Bedford Av

17、enue, Suite 201, Baltimore, MD 212081Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.2.8 nominal thickness, nthe finished liner thicknessafter curing.3.2.9 resin, npolyester, vinyl ester, epoxy or silicate resinsystems being ambient

18、 or steam cured.3.2.10 sectional cured in place lining (SCIPL), na textiletube impregnated by a thermo setting resin, which is formedwithin a portion of the existing pipe, thereby taking the shapeof, and fitting tightly to the existing pipe.3.2.11 tube, na textile tube capable of absorbing a thermos

19、et resin.4. Significance and Use4.1 This practice is for use by designers and specifiers,regulatory agencies, owners, and inspection organizations whoare involved in the rehabilitation of pipes through the use of aresin-impregnated tube installed within a damaged existingpipe. As for any practice, m

20、odifications may be required forspecific job conditions.5. Materials5.1 Tube5.1.1 The textile tube shall consist of one or more layers ofabsorbent textile, for example, needle punched felt or circularknit, fiberglass or similar textile materials that meet therequirements of Practice F 1216 and Requi

21、rements and TestMethods sections of Specification D 5813. The tube shall beconstructed to withstand installation pressures, have sufficientstrength to bridge missing pipe segments, and flexibility to fitirregular pipe sections. The wetout tube shall meet ResinImpregnation Requirements of Practice F

22、1216, and shall havea uniform thickness and with excess resin distribution thatwhen compressed at installation will meet or exceed the designthickness after cure.5.1.2 The tube shall be surrounded by an impermeableflexible translucent bladder that will contain the resin andfacilitate visual monitori

23、ng of the vacuum impregnation(wetout) procedure.5.1.3 The tube shall be continuous. No intermediate orencapsulated elastomeric layers shall be in the textile that maycause de-lamination in the finished cured in place pipe. Thetube shall be sized accordingly to create a circular lining equalto the in

24、side of the main pipe.5.1.4 The tube shall be fabricated with a 2 inch ring ofcompressible textile material at the upstream and downstreamends, to create a smooth transition. The compressible textilematerial will compress to meet the host pipe at its leading endand match the wall thickness of the tu

25、be at its opposite end.5.2 Resin5.2.1 The resin/liner system shall conform to Test Methodssection of Specification 5813- 10,000-hour test and TestMethod D 3681 using a 10,000 hour test period.5.2.2 The resin shall be a corrosion resistant polyester, vinylester, epoxy resin, or silicate and catalyst

26、system that whenproperly cured within the composite liner assembly, meets therequirements of Practice F 1216, the physical properties herein,and those, which are to be utilized in the design of the SCIPLfor this project.5.2.3 The resin shall produce a SCIPL, which will complywith the structural and

27、chemical resistance requirements ofPractice F 1216.6. Design Considerations6.1 The SCIPL shall be designed per Practice F 1216,Appendix X1, Section X1.1.2.6.2 The SCIPLdesign for the sectional liner shall assume nobonding to the original pipe.7. Installation Recommendations7.1 Access SafetyPrior to

28、entering access areas such asmanholes or excavation pits, perform inspection or cleaningoperations, an evaluation of the atmosphere shall be conductedto determine the presence of toxic or flammable vapors or lackof oxygen in accordance with local, state, or federal safetyregulations.7.1.1 Cleaning a

29、nd Inspection as per NASSCO Guidelines.7.1.2 Inspection of PipelinesThe interior of the pipelineshall be carefully inspected to determine the location of anycondition that shall prevent proper installation, such as roots,and collapsed or crushed pipe. These conditions shall be noted.Experienced pers

30、onnel trained in locating breaks, obstacles,and service connections by closed circuit television shallperform inspection of pipelines.7.1.3 Line ObstructionsThe existing host pipe shall beclear of obstructions that prevent the proper insertion andexpansion of the lining system. Changes in pipe size

31、shall beaccommodated according to the pipe diameter and condition.Obstructions may include dropped or offset joints of more than20 % of inside pipe diameter.7.2 Resin ImpregnationThe tube encapsulated within thetranslucent bladder (liner/bladder assembly) shall be vacuum-impregnated with resin (wet-

32、out) under controlled conditions.The volume of resin used shall be sufficient to fill all voids inthe tube material at nominal thickness and diameter. Thevolume shall be adjusted by adding excess resin for the changein resin volume due to polymerization and to allow for anymigration of resin into th

33、e cracks and joints in the original pipe.No dry or unsaturated area in the main tube shall be acceptableupon visual inspection.7.3 Liner InsertionThe bladder and tube (liner/bladderassembly) is drawn inside the launcher through the open end.The liner/bladder assembly is contained within the launcher

34、,protecting the tube from resin loss. The launcher is insertedinto the pipe and towed to the beginning of the damagedsection. When positioned, pressurized air is introduced causingthe liner/bladder assembly to project out of the launchersimultaneously inverting and inflating the resin impregnatedtub

35、e against the host pipe. When fully inverted, the tube iscontinuous in length covering the damaged section and extendsa minium of 189 on each side of the damaged section of thehost pipe.7.4 CuringAfter liner placement is completed; pressure ismaintained pressing the liner firmly against the inner pi

36、pe wall.The liner is cured at ambient temperatures or by a suitable heatsource. The heating equipment shall be capable of delivering amixture of steam and air throughout the liner bladder assemblyto uniformly raise the temperature above the temperatureF2599062required to cure the resin. The curing o

37、f the SCIPL shall takeinto account the existing pipe material, the resin system, andground conditions (temperature, moisture level, and thermalconductivity of the soil). The temperature shall be monitoredand logged during the cure and cool down cycles.7.5 Curing ProcessingCuring shall be done withou

38、t pres-sure interruption with air or a mixture of air and steam for theproper duration of time per the resin manufacturers recom-mendations. When the heat source is removed and the tem-perature of the SCIPL reaches 100 degrees F or less, theprocessing shall be finished. For an ambient cured method,

39、acoupon suspended in the manhole will determine curing time.7.6 Bladder RemovalA visual inspection during bladderremoval will verify the completion cure.8. Finish8.1 The finished SCIPL shall be continuous over the entirelength of the rehabilitated section of pipe. The SCIPL shall befree of dry spots

40、, lifts, and delamination. The cured liner shalltaper at each end so as to accept video equipment and maintaina proper flow. After the work is completed, the installer willprovide the owner with video footage documenting the com-pleted work, as per NASSCO Guidelines.9. Recommended Inspection Practic

41、es9.1 SamplingAs designated by the purchaser in the pur-chase agreement, the preparation of a SCIPL sample is re-quired. The sample shall be the same textile tube material andresin system as used for the rehabilitated pipe.9.1.1 The minimum length of the sample must be able toproduce at least five s

42、pecimens for testing in accordance withTest Method D 790.9.2 Short-Term Flexural (Bending) PropertiesThe initialtangent flexural modulus of elasticity and flexural strengthshall be measured for gravity pipe applications in accordancewith Test Method D 790 and shall meet the minimum require-ments of

43、Table 1.10. Keywords10.1 Sectional cured-in-place lining; tube; sheet; vacuumimpregnate; continuous; bladder; textile; felt; knit; resin; in-version; inflation; ambient cure; steam cure; launcher; liner/bladder assemblyASTM International takes no position respecting the validity of any patent rights

44、 asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any ti

45、me by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will

46、receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM

47、International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 SCIPL Initial Physical PropertiesProperty ASTM Test Minimum valuepsi (MPa)Flexural strength D 790 4,500 (31)Flexural modulus D 790 250,000 (1,724)F2599063