ASTM F2536-2006b Standard Guide for Installing Plastic DWV Piping Suspended from On-Grade Slabs《安装悬浮在高级厚板上塑料排气管道的标准指南》.pdf

《ASTM F2536-2006b Standard Guide for Installing Plastic DWV Piping Suspended from On-Grade Slabs《安装悬浮在高级厚板上塑料排气管道的标准指南》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2536-2006b Standard Guide for Installing Plastic DWV Piping Suspended from On-Grade Slabs《安装悬浮在高级厚板上塑料排气管道的标准指南》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 2536 06bStandard Guide forInstalling Plastic DWV Piping Suspended from On-GradeSlabs1This standard is issued under the fixed designation F 2536; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revisi

2、on. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.Note Sections 2 and 5 were revised from the previous 2006a version and the year date was changed on Sept. 29, 2006.1. Scope1.1 This guide pr

3、ovides procedures for the installation ofDWV piping in buildings that are built where soil conditionsrequire the use of pier or piling supported grade beamconstruction or in filled ground where the soil compaction isless than 95 %. These procedures are intended to ensure thatthe DWV piping suspended

4、 from the on grade concrete slabs isnot damaged or destroyed by movement of the soil or fill underthe slab after the building is completed and occupied.1.2 In this type of construction, the area within the gradebeams is filled with soil up to a level that allows the concreteslab to be poured directl

5、y on the fill without a supporting form.In this process the sanitary waste piping is installed bytrenching into the fill, and then putting hangers with supportrods on the pipes as they are installed. The hanger rodsextending upward must be long enough so that the top of therod will be embedded in an

6、d anchored in the concrete.1.3 The hanger rods are intended to provide adequatestrength and corrosion resistance to assure long term service.1.4 The details of installation are intended to ensure that therods remain vertical, that they extend into the concrete anadequate amount and that the upper en

7、ds are terminated so thatthey have adequate “pull out”strength.1.5 The details of backfill are intended to limit or minimizethe loads on the a suspended piping. These loads result fromconsolidation or movement of the soil/fill beneath the slab.1.6 This standard does not purport to address all of the

8、safety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 653 Terminology Relating t

9、o Soil, Rock, and ContainedFluidsD 2665 Specification for Poly(Vinyl Chloride) (PVC) Plas-tic Drain, Waste, and Vent Pipe and FittingsF 412 Terminology Relating to Plastic Piping Systems3. Terminology3.1 GeneralDefinitions used in this guide are in accor-dance with Terminologies in F 412 and D 653 u

10、nless otherwiseindicated.3.2 Definitions of Terms Specific to This Standard:3.2.1 grade beamsconcrete beams around the perimeterof a building and within the building. They support the slabs,the exterior walls and interior bearing walls.3.2.2 piers suspended DWV; underslabTABLE 1 Hanger RodsPipe Size

11、s Minimum Rod Size2 in. and smaller38 in.3 in. and 4 in.12 in.6in.58 in.8 in. and larger34 in.F 2536 06b2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that

12、 determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapprov

13、ed or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you fee

14、l that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).FIG. 1 Load Limiting MethodsF 2536 06b3