ASTM F2509-2015 Standard Specification for Field-assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene and Polyamide-11 (PA11) Gas Distribution Pipe an.pdf
《ASTM F2509-2015 Standard Specification for Field-assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene and Polyamide-11 (PA11) Gas Distribution Pipe an.pdf》由会员分享,可在线阅读,更多相关《ASTM F2509-2015 Standard Specification for Field-assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene and Polyamide-11 (PA11) Gas Distribution Pipe an.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F2509 12F2509 15Standard Specification forField-assembled Anodeless Riser Kits for Use on OutsideDiameter Controlled Polyethylene and Polyamide-11 (PA11)Gas Distribution Pipe and Tubing1This standard is issued under the fixed designation F2509; the number immediately following the desig
2、nation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope Scope*1.1 This specification cover
3、s requirements and test methods for field-assembled anodeless riser kits for use with outsidediameter controlled polyethylene and PA11 gas distribution pipe and tubing in sizes through 2 IPS as specified inspecificationSpecification D2513. polyethylene and Specification F2945 for PA11.1.2 The test m
4、ethods described are not intended to be routine quality control tests.1.3 This specification covers the types of field-assembled anodeless riser kits described in 3.3.2.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematicalconversio
5、ns to SI units that are provided for information only and not considered standard.1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes(excluding those in tables and figures), shall not be considered as requirements of the standard
6、.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatorylimitations prior to use.2. Referenced
7、 Documents2.1 ASTM Standards:2A513A513/A513M Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical TubingA53/A53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and SeamlessD638 Test Method for Tensile Properties of PlasticsD1600 Terminology for Abb
8、reviated Terms Relating to PlasticsD2513 Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and FittingsF412 Terminology Relating to Plastic Piping SystemsF1948 Specification for Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas DistributionPipe and Tu
9、bingF2897 Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing,Fittings, Valves, and Appurtenances)F2945 Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings2.2 ASME Standards:3ASME Boiler and Pressure Vessel Code3ASME B1.
10、20.1 Pipe Threads, General Purpose (Inch)4B31.8 Gas Transmission and Distribution Piping Systems1 This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.60 on Gas.Current edition approved Aug. 1, 2012Nov. 1, 2
11、015. Published October 2012December 2015. Originally approved in 2006. Last previous edition approved in 2012 asF250906(2012).F250912. DOI: 10.1520/F2509-12.10.1520/F2509-15.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For A
12、nnual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3 Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http:/www.asme.org.4 Available from the Superi
13、ntendent of Documents, U.S. Government Printing Office, Washington, DC 20402.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequatel
14、y depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM Inter
15、national, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States12.3 Federal Regulations:4United States CFR, Title 49, Part 192 Pipeline Safety Regulations2.4 UL Standard:5UL 360 Standard for Liquid-Tight Flexible Steel Conduit3. Terminology3.1 The gas industry terminolo
16、gy used in this specification is in accordance with ASME B31.8 or the United States CFR, Title49, Part 192, unless otherwise indicated.3.1.1 pipeused herein refers to both “pipe” and “tubing” unless specifically stated otherwise.3.1.2 gasused herein refers to any fuel gas unless specifically stated
17、otherwise.3.2 DefinitionsDefinitions are in accordance with Terminology F412 unless otherwise specified. Abbreviations are inaccordance with Terminology D1600 unless otherwise specified.3.3 Definitions:3.3.1 anodeless riser, na type of mechanical fitting which is designed to transport gas from under
18、ground polyethylene or PA11piping to above-ground metallic piping. When properly installed, polyethylene pipe the polyethylene or PA11 piping is the gascarrier in the below ground portion of an anodeless riser and is protected by a metallic riser casing when it extends above groundlevel.3.3.2 field-
19、assembled anodeless riser kit, nA kit containing all of the elements required to assemble an anodeless riser at thepoint of installation with the exception of the gas-carrying polyethylene pipe. or PA11 piping. It consists of, at a minimum, a risercasing and a riser adapter.These components may be e
20、ither integrally combined or include provisions for attachment to one anotherat the point of installation.3.3.3 mechanical fitting, na device for making a connection between piping components that employs physical force todevelop a leak-tight seal, produce alignment, and provide resistance to pullou
21、t caused by axial loads.3.3.4 riser adapter, na type of mechanical fitting used to join polyethylene and PA11 pipe to a metallic piping connection(typically a pipe thread). Riser adapters are sometimes referred to as service head adapters.3.3.5 riser casing, nthe metallic, non-gas carrying portion o
22、f an anodeless riser that serves as a protective conduit for thepolyethylene pipe. or PA11 piping. It may be either rigid, flexible, or a combination of both.3.3.6 qualified installation instructions, na written procedure for making a plastic mechanical joint that has been demonstratedwill meet the
23、requirements set forth in the United States CFR, Title 49, Part 192.283(b), and this standard.4. Materials and Manufacture4.1 General:4.1.1 All materials of the riser kit shall meet the performance requirements of this specification and applicable referencedspecifications. Specific materials referen
24、ced in this section are common materials used in these types of products. Alternatematerials proven to provide equal or better performance shall be acceptable.4.1.2 All burrs on metal components which could damage the polyethylene or PA11 piping during assembly shall either beremoved or suitably cov
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF25092015STANDARDSPECIFICATIONFORFIELDASSEMBLEDANODELESSRISERKITSFORUSEONOUTSIDEDIAMETERCONTROLLEDPOLYETHYLENEANDPOLYAMIDE11PA11GASDISTRIBUTIONPIPEANPDF
链接地址:http://www.mydoc123.com/p-538882.html