ASTM F2453 F2453M-2014 Standard Specification for Welded Wire Mesh Fence Fabric &40 Metallic-Coated or Polymer Coated&41 for Meshes of 6 in 2&8201 [3871 mm2] or Less in Panels or R.pdf

《ASTM F2453 F2453M-2014 Standard Specification for Welded Wire Mesh Fence Fabric &40 Metallic-Coated or Polymer Coated&41 for Meshes of 6 in 2&8201 [3871 mm2] or Less in Panels or R.pdf》由会员分享，可在线阅读，更多相关《ASTM F2453 F2453M-2014 Standard Specification for Welded Wire Mesh Fence Fabric &40 Metallic-Coated or Polymer Coated&41 for Meshes of 6 in 2&8201 [3871 mm2] or Less in Panels or R.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F2453/F2453M 05 (Reapproved 2011)1F2453/F2453M 14Standard Specification forWelded Wire Mesh Fence Fabric (Metallic-Coated or PolymerCoated) for Meshes of 6 in.2 3871 mm2 or Less, in Panelsor Rolls, with Uniform Meshes1This standard is issued under the fixed designation F2453/F2453M; the

2、 number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1 NO

3、TEReapproved and editorially revised throughout in February 2011.1. Scope1.1 This specification covers welded wire mesh fence fabric produced from steel wire or metallic-coated steel wire. Themetallic-coated fabric may be polymer coated after fabrication.1.2 Welded wire mesh fence fabric is produced

4、 in four types, based on the kind of coating, as described in Section 4.1.3 This specification is applicable to orders in either inch-pound units or SI units. Values stated in either inch-pound or SI unitsare to be regarded separately as the standard. Within the text, the SI units are shown in brack

5、ets. The values in the two systemsare not exact equivalents; therefore, each system shall be used independent of the other, without combining values in any way.1.4 This specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excludingthose in tabl

6、es and figures) shall not be considered as requirements of this specification.1.5 The following safety hazards caveat pertains only to the test methods portion, Section 13, of this specification: This standarddoes not purport to address all of the safety concerns, if any associated with its use. It

7、is the responsibility of the user of thisstandard to establish appropriate safety and health practices and determine the applicability of regulatory limitations proper touse.2. Referenced Documents2.1 ASTM Standards:2A82/A82M Specification for Steel Wire, Plain, for Concrete Reinforcement (Withdrawn

8、 2013)3A90/A90M Test Method for Weight Mass of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy CoatingsA123/A123M Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel ProductsA185/A185M Specification for Steel Welded Wire Reinforcement, Plain, for Concrete (Withdrawn 201

9、3)3A641/A641M Specification for ZincCoated (Galvanized) Carbon Steel WireA853 Specification for Steel Wire, Carbon, for General UseA856/A856M Specification for Zinc-5 % Aluminum-Mischmetal Alloy-Coated Carbon Steel WireA902 Terminology Relating to Metallic Coated Steel ProductsB117 Practice for Oper

10、ating Salt Spray (Fog) ApparatusD1499 Practice for Filtered Open-Flame Carbon-Arc Exposures of PlasticsF934 Specification for Colors for Polymer-Coated Chain Link Fence Materials2.2 ISO Standard:4ISO 2178 Non-Magnetic Coatings on Magnetic SubstratesMeasurement of Coating ThicknessMagnetic Method1 Th

11、is specification is under the jurisdiction of ASTM Committee F14 on Fences and is the direct responsibility of Subcommittee F14.35 on Architectural Metal FenceSystems.Current edition approved Feb. 1, 2011April 1, 2014. Published March 2011April 2014. Originally approved in 2005. Last previous editio

12、n approved in 20052011 asF2453/F2453M - 05.F2453/F2453M - 05(2011)1 DOI:10.1520/F2453_F2453M-05R11E01 DOI:10.1520/F2453_F2453M-14.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume informati

13、on, refer to the standards Document Summary page on the ASTM website.3 The last approved version of this historical standard is referenced on www.astm.org.4 Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http:/www.ansi.org.This document is

14、 not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropr

15、iate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13. Terminology3.1 DefinitionsRefer to Terminology A902 for gener

16、al terminology relating to metallic-coated steel products.3.2 Definitions of Terms Specific to This Standard:3.2.1 welded wire mesh fence fabricmaterial composed of a series of longitudinal and transverse steel wires arrangedsubstantially at right angles to each other, and welded together at the poi

17、nts of intersection by electrical resistance welding to formfabricated sheets or rolls. See Tables 1 and 2 for list of standard mesh sizes.4. Classification4.1 Welded wire mesh fence fabric is classified in accordance with coating as follows:4.1.1 Type 1, consists of welded wire fabric made from wir

18、e which is zinc-coated, as per Specification A641/A641M Class 3minimum, before being welded into fabric, known as galvanized before welding.4.1.2 Type 2, consists of welded wire fabric which is made from uncoated wire and the fabric is subsequently zinc-coated afterfabrication, in accordance with Sp

19、ecification A123/A123M, Coating Grade 35, known as galvanized after welding.4.1.3 Type 3, consists of welded wire fabric made from wire which is coated with zinc-5 % aluminum-mischmetal alloy(Zn-5A1-MM), in accordance with Specification A856/A856M, Class A, before being welded into fabric, known as

20、zinc 5 %aluminum mischmetal alloy-coated steel before welding.4.1.4 Type 4, consists of welded wire fabric made from wire which is zinc-coated, in accordance with SpecificationA641/A641M, Class 1 minimum, before being welded into fabric, known as galvanized before welding, and subsequently polymerco

21、ated.4.1.5 In agreement between buyer and supplier Type 1, 2 or 3 can be used to produce polymer coated welded wire fabric.5. Ordering Information5.1 Orders for material purchased under this specification shall include the following information:5.1.1 Quantity (number of units of rolls or panels)5.1.

22、2 Mesh description: wire spacing and size (gage)5.1.3 Panel (height by length) or Roll (height by length)5.1.4 Type of coating (Section 4), including the specific type to be furnished.5.1.5 ASTM designation and year of issue.5.1.6 Any special requirements (see Section 8).5.1.7 Certification, if requ

23、ired (see 15.1)NOTE 1A typical ordering description, when same mesh and gage, is as follows: 500 panels0.5 in. by 3 in. by 8.5 gage/120 in. by 99 in. Type 2,TABLE 1 Panel SizesAMesh Size as Produced in PanelsPanels Vertical MeshSpacing (in.)Horizontal MeshSpacing (in.)Wire Diameter Panel Width for P

24、ostSpacings 6, 7, 8, and 10 ft(in.)Panel Length (Height) (ft)Gage in. mm0.5 2.0 11 0.120 3.06 74, 86, 98, 122 6 - 210.5 3.0 8.5 0.155 3.93 75, 87, 99, 123 6 - 210.5 3.0 11 0.120 3.06 75, 87, 99, 123 6 - 212.0 2.0 11 0.120 3.06 74, 86, 98, 122 6 - 212.0 2.0 8.5 0.155 3.93 74, 86, 98, 122 6 - 212.0 2.

25、0 6.5 0.185 4.70 74, 86, 98, 122 6 - 21TABLE 1 Panel SizesAVertical MeshSpacing (in.)Horizontal MeshSpacing (in.)Wire Diameter Panel Width for PostSpacings 6, 7, 8, and 10 ft(in.)Panel Length (Height) (ft)Guage in. mm2.0 2.0 11 0.120 3.06 74, 86, 98, 122 6 - 212.0 2.0 8.5 0.155 3.93 74, 86, 98, 122

26、6 - 212.0 2.0 6 0.192 4.88 74, 86, 98, 122 6 - 212.0 2.0 6.5 0.185 4.70 74, 86, 98, 122 6 - 210.5 2.0 10.5 0.128 3.25 74, 86, 98, 122 6 - 210.5 2.0 11 0.120 3.06 74, 86, 98, 122 6 - 210.5 3.0 11 0.120 3.06 75, 87, 99, 123 6 - 210.5 3.0 10.5 0.128 3.25 75, 87, 99, 123 6 - 210.5 3.0 9 0.148 3.77 75, 8

27、7, 99, 123 6 - 210.5 3.0 8.5 0.155 3.94 75, 87, 99, 123 6 - 210.5 3.0 8 0.162 4.12 75, 87, 99, 123 6 - 210.5 3.0 6 0.192 4.88 75, 87, 99, 123 6 - 210.75 3.0 4 0.225 5.72 75, 87, 99, 123 6 - 21APanels available up to 10 ft 6 in. in width (not all meshes) and 21 ft in length.The vertical mesh spacing

28、is the distance measured from the top to the bottom.The horizontalmesh opening is the distance measured from left to right.F2453/F2453M 142conforming to Specification F2453 or 100 rolls of 2 in. by 2 in. 8.5 gage/96 in. by 100 ft, Type 1, conforming to Specification F2453. The vertical meshopening (

29、height measured from top to bottom) is designated first followed by the horizontal mesh opening (width measured from left to right).6. Material and Manufacture6.1 The wire used in the manufacture of welded wire mesh fence fabric shall conform to the specifications in 6.1.1 asappropriate for the type

30、 ordered, except the tensile strength shall conform to 7.1. The wire may be produced from any grade ofsteel listed in Specification A82/A82M or Specification A853.6.1.1 Type 1 welded wire fabric shall be manufactured from zinc-coated steel wire conforming to Specification A641/A641MClass 3 coating (

31、minimum). Type 2 welded wire fabric shall be manufactured from uncoated steel wire conforming to SpecificationA82/A82M or Specification A853, and the fabric subsequently zinc-coated by the hot-dip process, conforming to SpecificationA123/A123M, Coating Grade 35 (minimum). Type 3 welded wire fabric s

32、hall be manufactured from zinc-5 % a1uminum-mischmetal coated steel wire conforming to Specification A856/A856M, Class A coating (minimum). Type 4 welded wire fabricshall be manufactured from zinc-coated steel wire conforming to Specification A641/A641MClass 1 coating.6.2 Wire for welded wire mesh f

33、ence fabric shall be assembled by automatic machines or other suitable mechanical means thatwill ensure accurate spacing and alignment of all members of the finished fabric. Longitudinal and transverse members of thewelded wire fabric shall be connected at every intersection in accordance with the r

34、equirements of 13.4 by the process of electricresistance welding, which employs the principle of fusion combined with pressure.6.3 The polymer coating used in the manufacture of polymer-coated welded wire mesh fence fabric shall conform to theproperties in 8.2 and 8.3.6.3.1 The polymer-coated welded

35、 wire mesh fence fabric shall have the polymer coating fused and adhered onto themetallic-coated welded wire fabric after fabrication of mesh.7. Mechanical PropertiesTensile Strength7.1 Tensile StrengthThe tensile strength of the wire used for the welded wire mesh fence fabric shall be soft, medium

36、or hardin accordance with the requirements of Specifications A641/A641M (Type 1 and 4), A856/A856M (Type 3) and hard drawn inaccordance with Specification A82/A82M or Specification A853 (Type 2). The cross-sectional area of the test specimen shall bebased on the diameter of the metallic coated wire.

37、 (See Table 3.)8. Physical Properties8.1 Metallic CoatingThe minimum metallic coating weight shall conform to the requirements of Specification A641/A641M,Class 3 coating for Type 1 and Type 2 and Specification A856/A856M Class A coating for Type 3.8.2 Polymer CoatedThe minimum coating weight of the

38、 metallic coated wire shall conform to the requirements ofSpecification A641/A641M Class 1 for Type 4.8.3 Polymer Coating on WireThe initial properties of the polymer coating on the wire and welded wire fabric shall have ademonstrated ability to conform to the following requirements:8.3.1 Salt Spray

39、 Exposure and Ultraviolet Light Exposure:8.3.1.1 The polymer coating shall show no effect after 1000 h of salt spray exposure in accordance with Practice B117.TABLE 2 Roll SizesAMesh Size as Produced in RollsVertical Mesh Spacing Horizontal Mesh Spacing Wire Diameter Roll Height (Width)in. mm in. mm

40、 Gage in. mm ft1.0 25 1.0 25 12.5 0.99 2.51 3 - 10.51.0 25 1.0 25 11 .120 3.06 3 - 10.51.5 38 1.5 38 12.5 .099 2.51 3 - 10.51.5 38 1.5 38 11 .120 3.06 3 - 10.52.0 50 2.0 50 11 .120 3.06 3 - 10.52.0 50 2.0 50 10 .135 3.43 3 - 10.52.0 50 2.0 50 8.5 .155 3.93 3 - 10.52.0 50 2.0 50 6.5 .185 4.70 3 - 10.

41、52.4 60 2.4 60 10 .135 3.43 3 - 10.52.4 60 2.4 60 8.5 .155 3.93 3 - 10.52.0 50 0.5 13 11 .120 3.06 3 - 10.52.0 50 1.0 25 11 .120 3.06 3 - 10.52.0 50 1.0 25 10 .135 3.43 3 - 10.53.0 75 1.0 25 12.5 .099 2.51 3 - 10.53.0 75 1.0 25 11 .120 3.06 3 - 10.5ARolls available up to 10 ft 6 in. in width (not al

42、l meshes) in foot increments up to 100 ft in length. The vertical mesh spacing is the distance measured from the top to thebottom. The horizontal mesh opening is the distance measured from left to right.F2453/F2453M 1438.3.1.2 The polymer coating shall show no effect of exposure to ultraviolet light

43、 with test exposure of 1000 h using apparatusType E and 63C, when tested in accordance with Practice D1499.8.3.1.3 Evaluation of Coating after Salt Spray and Ultraviolet Exposure TestAfter 1000 h salt spray test and exposure toultraviolet light as specified in 8.3.1.1 and 8.3.1.2, the polymer coatin

44、g shall not show cracks, blisters or splits. The change in color,measured in terms of E, shall not be more than ten.8.3.2 AdhesionThe polymer coating shall adhere to the wire such that the coating breaks rather than separates from the wirewhen tested in accordance with 13.3.8.3.3 Mandrel BendThe pol

45、ymer-coated wire when subjected to a single 360 bend at 0F 18C around a mandrel tentimes the diameter of the wire, shall not exhibit breaks or cracks in the polymer coating.8.3.4 ColorUnless otherwise agreed upon between buyer and supplier, the color of the polymer-coated wire shall conform toSpecif

46、ication F934.9. Dimensions and Tolerances9.1 The diameter of metallic-coated wire shall conform to Table 3.9.2 The minimum thickness of the polymer coating, not to be considered the finished gage, shall be as shown in Table 4.9.3 Welded wire mesh fence fabric shall have mesh openings as designated i

47、n Tables 1 and 2. Mesh opening shall be consideredto be center-to-center distance between two consecutive longitudinal or transverse wires as designated inFig. 1. The permissible tolerance is 618 in. 3.2 mm on meshes 2 in. and above and 116 in. 1.6 mm on meshes under 2 inches.9.4 In panel or roll le

48、ngth, the permissible tolerance shall not exceed 614 in. 6.3 mm when measured over a 6 ft direction.In all cases, the mesh count must be correct.9.5 The width and height of the mesh openings for welded wire mesh fence fabric as installed on fence posts shall be as shownin Fig. 2.9.6 The flatness of

49、panels shall conform to the following: when a panel is laid on a flat surface, such that any lift is in the middleof the panel, the maximum lift shall not exceed 2 in. 50.8 mm.10. Workmanship10.1 Wire of proper grade and quality, when fabricated in the manner herein required, shall result in a strong, serviceablemesh-type product having substantially square or rectangular openings. It shall be fabricated and finished in a workmanlikemanner, as determined by visual inspection, and shall conform to this specification.TABLE 3 Bre