ASTM F2390-2012 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain Waste and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content《含有后工业化回收内容的聚氯乙烯 (P.pdf
《ASTM F2390-2012 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain Waste and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content《含有后工业化回收内容的聚氯乙烯 (P.pdf》由会员分享,可在线阅读,更多相关《ASTM F2390-2012 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain Waste and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content《含有后工业化回收内容的聚氯乙烯 (P.pdf(9页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F2390 07F2390 12 An American National StandardStandard Specification forPoly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent(DWV) Pipe and Fittings Having Post-Industrial RecycleContent1This standard is issued under the fixed designation F2390; the number immediately following the
2、designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope Scope*1.1 This specification
3、covers requirements and test methods for materials, dimensions and tolerances, pipe stiffness, crushresistance, impact resistance, hydrostatic burst resistance, and solvent cement for poly(vinyl chloride) plastic drain, waste, and vent(DWV) pipe and fittings.1.2 The values stated in inch-pound units
4、 are to be regarded as the standard. The metric equivalents of inch-pound units valuesgiven in parentheses may be approximate.are mathematical conversions to SI units that are provided for information only and arenot considered standard.1.3 The text of this specification references notes, footnotes,
5、 and appendixes which provide explanatory material. These notesand footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This
6、standarddoes not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.NOTE 1Pressurized (compres
7、sed) air or other compressed gases contain large amounts of stored energy which present serious safety hazards shoulda system fail for any reason.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1599 Test Method for Resistance to Short-Time Hydraulic Pre
8、ssure of Plastic Pipe, Tubing, and FittingsD1600 Terminology for Abbreviated Terms Relating to PlasticsD1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)CompoundsD2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fitting
9、sD2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (FallingWeight)D2564 Specification for Solvent Cements for Poly(Vinyl Ch
10、loride) (PVC) Plastic Piping SystemsF2135 Specification for Molded Drain, Waste, and Vent (DWV) Short-Pattern Plastic FittingsD3311 Specification for Drain, Waste, and Vent (DWV) Plastic Fittings PatternsD4396 Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (C
11、PVC) Compounds forPlastic Pipe and Fittings Used in Nonpressure ApplicationsF402 Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and FittingsF412 Terminology Relating to Plastic Piping SystemsF1498 Specification for Taper Pipe Threads 60 for T
12、hermoplastic Pipe and FittingsF1866 Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings1 This specification is under the jurisdiction ofASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV. Curr
13、entedition approved Feb. 1, 2007Nov. 1, 2012. Published February 2007January 2013. Originally approved in 2007. Last previous edition approved in 2007 as F239007. DOI:10.1520/F2390-07.10.1520/F2390-12.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Servic
14、e at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous
15、version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes
16、section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13. Terminology3.1 Definitions Definitions are in accordance with Terminology in F412, and abbreviations are in accordance withTerminology in D1
17、600, unless otherwise specified.3.2 Definitions of Terms Specific to This Standard:3.2.1 certificate of composition disclosure, na certificate describing certain properties of an external recycled material, itsformulation and source, and the specific material shipment to which it applies.3.2.1.1 Dis
18、cussionExamples include polymer(s), molecular weight, percentage (and type) of inorganic material, tensile strength, modulus ofelasticity, and izod impact; code or designation identifying the formulation and source information.3.2.2 post-industrial recycle, nrecycled PVC material generated by a comp
19、any or manufacturing plant that is different thanthe location producing products to this specification.3.2.2.1 DiscussionMaterial used for a different product produced by the same manufacturer shall be considered as post-industrial recycle material forthe product of this standard, unless the differe
20、nt product is made from the same compound.3.2.3 post-consumer recycle, nPVC plastic material used in products that have proceeded into the chain of commerce beyondthe control of the original manufacturer.3.2.3.1 DiscussionThese materials are generally recycled by the users or consumers of the produc
21、t, and have no specific identity or specificity of thecompound.3.2.3.2 DiscussionPost-consumer recycled material is NOTpost-industrial recycle and is prohibited from use in products within this specification (see5.4.1)4. Significance and Use4.1 The requirements of this specification are intended to
22、provide pipe and fittings suitable for the drainage and venting ofsewage and certain other liquid wastes.NOTE 2This standard specifies dimensional, performance and test requirements for plumbing and fluid handling, but does not address venting ofcombustion gases.NOTE 3Industrial waste disposal lines
23、 should be installed only with the specific approval of the cognizant building code authority since chemicalsnot commonly found in drains and sewers and temperatures in excess of 180 F (82.2 C) may be encountered.5. Materials5.1 Basic MaterialsThe pipe and fittings shall be made from a uniform blend
24、 containing virgin PVC compound and between10 % by weight and 50 % by weight of post-industrial recycle material. The finished compound shall meet or exceed the minimumcell classification material requirements specified in 5.2, Virgin PVC Compounds.5.2 Virgin PVC CompoundsVirgin PVC pipe compounds s
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF23902012STANDARDSPECIFICATIONFORPOLYVINYLCHLORIDEPVCPLASTICDRAINWASTEANDVENTDWVPIPEANDFITTINGSHAVINGPOSTINDUSTRIALRECYCLECONTENT

链接地址:http://www.mydoc123.com/p-538587.html