ASTM F718-2007 Standard for Shipbuilders and Marine Paints and Coatings Product Procedure Data Sheet《造船厂和船舶漆及涂层制品 程序数据单的标准》.pdf

《ASTM F718-2007 Standard for Shipbuilders and Marine Paints and Coatings Product Procedure Data Sheet《造船厂和船舶漆及涂层制品 程序数据单的标准》.pdf》由会员分享，可在线阅读，更多相关《ASTM F718-2007 Standard for Shipbuilders and Marine Paints and Coatings Product Procedure Data Sheet《造船厂和船舶漆及涂层制品 程序数据单的标准》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 718 07An American National StandardStandard Specification forShipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet1This standard is issued under the fixed designation F 718; the number immediately following the designation indicates the year oforiginal adoption or,

2、in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1

3、 The Shipbuilders and Marine Paints and CoatingsProduct/Procedure Data Sheet2provides on one sheet neededinformation concerning the characteristics of a specific paint orcoating to include generic description, physical properties,surface preparation requirements, application requirements,and safety.

4、 The front side of the sheet contains four major,numbered paragraphs and a highlighted section for SpecialSafety Precautions. These paragraphs are as follows:I. Generic Type and DescriptionII. Manufacturers DataIII. PropertiesIV. Surface Preparation Minimum RequirementsThe back side of the page cont

5、ains the following paragraphs:V. Mixing ProcedureVI. Application.1.2 The completed data sheets can be used by technicalpersonnel to help evaluate the technical acceptability of aproposed material, by production personnel to evaluate pro-duction compatibility of proposed materials and to provideappli

6、cation instructions for selected paints and coatings mate-rials, and by quality control personnel to verify attributes ofmaterials.2. Referenced Documents2.1 ASTM Standards:3D 56 Test Method for Flash Point by Tag Closed Cup TesterD 93 Test Methods for Flash Point by Pensky-MartensClosed Cup TesterD

7、 523 Test Method for Specular GlossD 1475 Test Method For Density of Liquid Coatings, Inks,and Related ProductsD 1640 Test Methods for Drying, Curing, or Film Forma-tion of Organic Coatings at Room TemperatureD 1650 Test Methods of Sampling and Testing ShellacVarnish4D 2697 Test Method for Volume No

8、nvolatile Matter inClear or Pigmented CoatingsD 3278 Test Methods for Flash Point of Liquids by SmallScale Closed-Cup Apparatus2.2 ASTM Adjunct:Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheets22.3 U.S. EPA Method:524 U.S. Environmental Protection Agency, 40 CFR Ch. 1,Part 60

9、, Appendix A, Determination of Volatile MatterContent, Density, Volume Solids, and Weight Solids ofSurface Coatings3. Instructions for Completing Data Sheet3.1 When filling out the Product/Procedure Data Sheet (seeFigs. 1 and 2) remember that the information contained thereinwill be utilized by both

10、 technical and production personnel.Keep it simple and brief but complete. The following instruc-tions are organized by paragraph numbers contained within thedata sheet.3.2 Paragraph IGeneric Type and DescriptionUse onlyknown and industry-accepted generic descriptions. Also, listany specification sp

11、ecific terminology (for example, MIL-PRF-23236 Type I, Class 2, etc.) See Fig. 1.3.3 Paragraph IIManufacturers DataThis section isself-explanatory with the possible exception of subparagraph(f). This can be as complete or as brief as the concerned partiesdesire. For example, a separate attached list

12、 of compatible andincompatible topcoats or acceptable cargo exposures could beincluded. See Fig. 1.1This standard is under the jurisdiction of ASTM Committee F25 on Ships andMarine Technology and is the direct responsibility of Subcommittee F25.01 onStructures.Current edition approved March 1, 2007.

13、 Published May 2007. Originallyapproved in 1981. Last previous edition approved in 2005 as F 718 99 (2005)e1.2Available from ASTM International Headquarters. Order Adjunct No.ADJF0718. Original adjunct produced in 1993.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact A

14、STM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4Withdrawn.5Available from U.S. Government Printing Office Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC

15、20401.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.FIG. 1 Data Sheet (Front)F718072FIG. 2 Data Sheet (Back)F7180733.4 Paragraph IIIPropertiesThis section is also self-explanatory with the following exceptions:3.4.1 Subparagraph (a

16、)If agreed upon by the concernedparties, a different method for determining volume solids(theoretical coverage) may be substituted. The form should beamended to show method.3.4.2 Subparagraph (e)If the specification requires anedge-retentive paint to be used, the % edge retention and testmethod used

17、 should be listed.3.4.3 Subparagraph (g)Use an agreed upon standard forviscosity (for example, ASTM, etc.). Also, for two partcoatings, state whether the requirement is for each individualcomponent, the mixed coating, or all three.3.4.4 Subparagraph (n)any special properties (for ex-ample, stain res

18、istance, low temperature cure, etc.) should belisted, and any specific differences in handling, application ormaintenance procedures to maintain that property should belisted. See Fig. 1.3.5 Special Safety PrecautionsThis section should con-tain specific instructions of what to do in the event of sk

19、in oreye contact or accidental ingestation, or both. Reference shouldalso be made to the appropriate manufacturers Material SafetyData Sheet. See Fig. 1.3.6 Paragraph IVSurface Preparation Minimum Require-ments:3.6.1 Subparagraphs (a) and (b)Use an agreed-uponstandard for example, ASTM, SSPC, Swedis

20、h, NACE,SNAME, etc. See Fig. 1.3.6.2 Subparagraph (c)Surface profile data is required.The profile listed must be given as a range for the average ofall profile measurements. The method of measurement must beagreed upon by all parties concerned.3.6.3 Subparagraph (d)Any specific requirements for, orp

21、rohibitions on, the type of abrasives that can be used shall beentered in subparagraph (d), Special Instructions. See Fig. 1.3.6.4 Subparagraph (f) and (g)List commercial industrystandard(s), or test method(s), or both, for conductivity andflash rust.3.7 Special Safety PrecautionsThis section should

22、 con-tain specific instructions of what to do in the event of skin oreye contact or accidental ingestion, or both. Reference shouldalso be made to the appropriate manufacturers Material SafetyData Sheet. See Fig. 1.3.8 Paragraph VMixing ProcedureThis section is self-explanatory with the possible exc

23、eptions of subparagraphs (c)and (f). Subparagraph (c) should preferably contain a genericsolvent as opposed to a proprietary one. Subparagraph (f)should, as a minimum, contain the mesh size of the strainingmaterial and special procedures governing which componentshould be added to the other. Subpara

24、graph (b), if appropriate,should include length of induction time given as a function ofvarious temperatures. See Fig. 2.3.9 Paragraph VIApplicationThis section is one of themost important of the entire form. It must be filled outaccurately and completely using all blocks in every paragraph.3.9.1 Su

25、bparagraph (c), “Dry Times”Provide either agraph or a chart showing the following cure times at aminimum:(1) dry to recoat(2) dry to handle (that is, time until personnel can walk on,inspect, touch-up coat)(3) maximum recoat(4) cure to full serviceThe graph or chart shall have at a minimum each of t

26、hesefour cure times at the stated minimum and maximum ambienttemperatures, and at least one data point in between (forexample, if a product can be applied as low as 40F, and ashigh as 100F, the chart or graph may need to dry to recoat, dryto handle, max recoat and cure to full service times for 40F,

27、100F, and 70F).Maximum recoat times should be expressed in hours, days,weeks, or months.3.9.2 Subparagraph (d)Equipment requirements shouldbe brief.3.9.3 Subparagraph (e)Special Instructions should in-clude mitigation steps to be followed when above conditionsnot met (for example, if max overcoat wi

28、ndow is missed), andrequire special handling to correct. See Fig. 2.4. Keywords4.1 data sheet; marine coatings; marine paints; proceduredata sheet; product data sheetASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin thi

29、s standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be

30、 reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresp

31、onsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F718074