ASTM F452-1976(2014) Standard Specification for Preformed Cranioplasty Plates《预制颅骨板的标准规格》.pdf

《ASTM F452-1976(2014) Standard Specification for Preformed Cranioplasty Plates《预制颅骨板的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM F452-1976(2014) Standard Specification for Preformed Cranioplasty Plates《预制颅骨板的标准规格》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F452 76 (Reapproved 2014)Standard Specification forPreformed Cranioplasty Plates1This standard is issued under the fixed designation F452; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, the year of last revision. A nu

2、mber in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers preformed cranioplasty plateswhich do not require further alteration for covering skulldefects. This specificat

3、ion covers compositional and physicalperformance and packaging requirements, but does not covertoxicity nor biocompatibility of the materials.2. Referenced Documents2.1 ASTM Standards:2F56 Specification for Stainless Steel Sheet and Strip forSurgical Implants (Withdrawn 1989)3F75 Specification for C

4、obalt-28 Chromium-6 MolybdenumAlloy Castings and Casting Alloy for Surgical Implants(UNS R30075)F86 Practice for Surface Preparation and Marking of Metal-lic Surgical ImplantsF139 Specification for Wrought 18Chromium-14Nickel-2.5Molybdenum Stainless Steel Sheet and Strip for Sur-gical Implants (UNS

5、S31673)2.2 American Society for Quality (ASQ) Standard:ASQ C1 Specifications of General Requirements for a Qual-ity Program43. Materials3.1 Cranioplasty plates conforming to this specificationshall be fabricated from materials described in the latest issueof Specifications F56, Grade 2, F75,orF139,

6、Grade 2. Thecondition of the material (such as, annealed, cold finished, andso forth) should be specified in the purchase order.4. Dimensions and Tolerances4.1 Cranioplasty plates conforming to this specificationshall be fabricated in a variety of dimensions to accommodate,without further alteration

7、, various sized skull defects.4.2 Shape shall be contoured so as to re-establish the normalconfiguration and symmetry of the skull at various anticipatedsites of defect such as the parietal bosses, the inion, the brow,the linea temporalis, and so forth.4.3 Plates shall contain multiple perforations

8、(see Fig. 1).4.4 Thicknesses and individual shapes shall vary with need.Thickness tolerances shall be as follows:Specified Thickness, in. (mm)Thickness Tolerances,in. (mm)0.005 (0.13) to 0.010 (0.25), incl 10 %0.010 (0.25) to 0.020 (0.51), incl 0.0015 (0.04)0.020 (0.51) to 0.035 (0.89), incl 0.002 (

9、0.05)0.035 (0.89) to 0.050 (1.27), incl 0.0025 (0.06)0.050 (1.27) to 0.100 (2.54), incl 0.003 (0.08)5. Finish and Identification5.1 Cranioplasty plates conforming to this specificationshall have their surfaces prepared in accordance with the latestissue of Practice F86. Specific requirements of surf

10、ace finish (ifany) shall be stated in the purchase order.5.2 The method of marking the plates shall be one of thosespecified in Practice F86.6. Precautions6.1 Cranioplasty plates covered by this specification shallnot be reshaped in any manner after manufacture.6.2 Material used to fasten the cranio

11、plasty plates coveredby this specification shall be the same alloy as the material usedto make the specific plate being installed.7. Packaging and Labeling7.1 Cranioplasty plates conforming to this specificationshall be supplied, packaged in accordance with the appropriaterecommended practice being

12、developed by ASTM CommitteeF04. Minimum packaging and labeling for cranioplasty platesshall include the following:7.1.1 An insert shall be included in the package for the plateshowing the material from which it was fabricated and include1This specification is under the jurisdiction of ASTM Committee

13、 F04 onMedical and Surgical Materials and Devices and is the direct responsibility ofSubcommittee F04.31 on Neurosurgical Standards.Current edition approved Oct. 1, 2014. Published November 2014. Originallyapproved in 1976. Last previous edition approved in 2008 as F452 76 (2008).DOI: 10.1520/F0452-

14、76R14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard

15、is referenced onwww.astm.org.4Available from American Society for Quality (ASQ), 600 N. Plankinton Ave.,Milwaukee, WI 53203, http:/www.asq.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1a recommendation against using fasteners ot

16、her than the samematerial or a recommended substitute to secure the plate whenimplanted.7.1.2 Labeling shall include the nominal thickness of theplate.8. Quality Program Requirements8.1 The manufacturer of cranioplasty plates covered by thisspecification shall maintain a quality program such as, for

17、example, defined in ASQ C1.9. Keywords9.1 cranioplasty plates; neurosurgical medical devices/applications; orthopaedic medical devices; bone platesASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users o

18、f this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every fiv

19、e years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical c

20、ommittee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA

21、 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 1 Preformed Cranioplasty PlateF452 76 (2014)2