ASTM F410-2008(2017) Standard Test Method for Wear Layer Thickness of Resilient Floor Coverings by Optical Measurement《光学测量法对弹性地板覆盖物磨损层厚度的标准试验方法》.pdf
《ASTM F410-2008(2017) Standard Test Method for Wear Layer Thickness of Resilient Floor Coverings by Optical Measurement《光学测量法对弹性地板覆盖物磨损层厚度的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM F410-2008(2017) Standard Test Method for Wear Layer Thickness of Resilient Floor Coverings by Optical Measurement《光学测量法对弹性地板覆盖物磨损层厚度的标准试验方法》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F410 08 (Reapproved 2017)Standard Test Method forWear Layer Thickness of Resilient Floor Coverings byOptical Measurement1This standard is issued under the fixed designation F410; the number immediately following the designation indicates the year of originaladoption or, in the case of r
2、evision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This test metho
3、d covers the determination of the thick-ness of the wear layer of resilient non-textile floor coverings, intile or sheet form, with or without felt backing or foam layer,by optical measurement.1.2 This test method is applicable for wear layers with aminimum thickness of 0.0004 in. (0.01 mm) to a max
4、imumthickness of 0.1 in. (2.54 mm), where measurements within0.0001 in. or 0.0025 mm are tolerable.1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not consid
5、ered standard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitation
6、s prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization Techn
7、icalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2E691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method3. Significance and Use3.1 This test method is applicable for wear layers with aminimum thickness of 0.001 in. (0.02 mm) to
8、 a maximumthickness of 0.1 in. (2.54 mm), where measurements within0.0005 in. or 0.01 mm are tolerable.4. Apparatus4.1 Compound Microscope, having a magnification of atleast 40, equipped with an eyepiece micrometer of the ruleddisk or filar type. The scale shall cover approximately 0.1 in.(2.54 mm)
9、and each division shall be equal to approximately0.0004 in. (0.01 mm) at the object. Either a binocular orstandard microscope may be used.4.2 Vertical Illuminator (recommended), to illuminate thespecimen. If another source is used, the light should fall on thespecimen from as nearly vertical directi
10、on as possible.4.3 Stage Micrometer, for calibrating the eyepiece microm-eter. The scale shall have the smallest division equal to 0.0004in. (0.01 mm) and shall cover at least 0.1 in. (2.54 mm). Thereference standard used for calibration shall be traceable to aNational Standard.4.4 HolderA means for
11、 holding the specimen, withoutdistortion, so that the cut edge is perpendicular to the opticalaxis of the microscope.4.5 Sharp Knife, or razor blade in a holder, for cutting thespecimen.4.6 Cutting Board of plastic, hardboard or fine-grainedhardwood.4.7 Straightedge, for guiding the cutting edge.5.
12、Test Specimen5.1 The specimen shall be cut from a properly selectedsample, representing the area to be measured. It shall beapproximately 2 in. (50 mm) long on the edge to be measuredby about 0.5 in. (13 mm) in width.6. Procedure6.1 Preparation of SpecimenPlace the sample on thecutting board with th
13、e face side up. Hold the cutting instrument1This test method is under the jurisdiction ofASTM Committee F06 on ResilientFloor Coverings and is the direct responsibility of Subcommittee F06.20 on TestMethods - Products Construction/Materials.Current edition approved Nov. 1, 2017. Published January 20
14、14. Originallyapproved in 1975. Last previous edition approved in 2013 as F41008 (2013). DOI:10.1520/F0410-08R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the
15、 standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in th
16、e Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1so that the plane of the blade is perpendicular to the face of thesample. The cutting edge of the blade should be at
17、an angle tothe horizontal that produces a clean cut. It is essential that thecut is perpendicular to the face of the sample. Apply sufficientpressure so that a clean cut can be made completely through thesample in one stroke, being careful not to distort the sample orturn the knife from the perpendi
18、cular. The cut should bestraight, and at least 2 in. (50 mm) long. Make a similar cutparallel to the first cut, about 0.5 in. (13 mm) apart. Cut eachend, so the specimen can be removed from the sample.6.2 Thickness Measurement:6.2.1 Mount the specimen with the long edge up, the cutsurface perpendicu
19、lar to the optical axis of the microscope (seeAppendix X1).6.2.2 CalibrationCalibrate the eyepiece micrometeragainst the stage micrometer, and record the calibration factor.If a variable magnification (zoom) instrument, or one withadjustable tube length is used, be sure that these adjustmentsare not
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF41020082017STANDARDTESTMETHODFORWEARLAYERTHICKNESSOFRESILIENTFLOORCOVERINGSBYOPTICALMEASUREMENT
链接地址:http://www.mydoc123.com/p-536603.html