ASTM F409-2002 Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings《可卸可更换的热塑性塑料管和管配件标准规范》.pdf
《ASTM F409-2002 Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings《可卸可更换的热塑性塑料管和管配件标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM F409-2002 Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings《可卸可更换的热塑性塑料管和管配件标准规范》.pdf(16页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F 409 02An American National StandardStandard Specification forThermoplastic Accessible and Replaceable Plastic Tube andTubular Fittings1This standard is issued under the fixed designation F 409; the number immediately following the designation indicates the year oforiginal adoption or,
2、 in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.
3、1 This specification covers requirements and test methodsfor materials, dimensions and tolerances, hydrostatic pressure,joint integrity, and solvent cement for thermoplastic tube andfittings for accessible and replaceable domestic waste connec-tions. Marking requirements are also included. Plastic w
4、hichdoes not meet the material requirements specified in Section 5is excluded.1.2 The text of this specification references notes, footnotes,and appendixes which provide explanatory material. Thesenotes and footnotes (excluding those in tables and figures) shallnot be considered as requirements of t
5、he specification.1.3 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.1.4 The following safety hazards caveat pertains only to thetest methods portion, Section 8, of this specification: Thisstandard does not purport to a
6、ddress all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:D 618 Practice
7、 for Conditioning Plastics for Testing2D 1600 Terminology for Abbreviated Terms Relating toPlastics2D 1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC) Compounds2D 2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and Fitting
8、s3D 2235 Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings3D 2564 Specification for Solvent Cements for Poly(VinylChloride) (PVC) Plastic Piping Systems3D 2609 Specification for Plastic Insert Fittings for Polyeth-ylene (PE) Plastic Pipe3D 2657 Prac
9、tice for Heat Joining of Polyolefin Pipe andFittings3D 2661 Specification for Acrylonitrile-Butadiene-Styrene(ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipeand Fittings3D 2665 Specification for Poly(Vinyl Chloride) (PVC) Plas-tic Drain, Waste, and Vent Pipe and Fittings3D 3965 Specification fo
10、r Rigid Acrylonitrile-Butadiene-Styrene (ABS) Compounds for Pipe and Fittings4D 4101 Specification for Propylene Plastic Injection andExtrusion Materials4F 402 Practice for Safe Handling of Solvent Cements,Primers, and Cleaners Used for Joining Thermoplastic Pipeand Fittings3F 412 Terminology Relati
11、ng to Plastic Piping Systems3F 1498 Specification for Taper Pipe Thread 60 for Ther-moplastic Pipe and Fittings32.2 Federal Standard:Fed. Std. No. 123 Marking for Shipment (Civil Agencies)52.3 Military Standard:MIL-STD-129 Marking for Shipment and Storage52.4 ANSI/ASME Standard:B1.20.1 Pipe Threads,
12、 General Purpose (Inch)62.5 Other Document:Uniform Plumbing Code73. Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F 412, and abbreviations are in accordance with Ter-minology D 1600, unless otherwise specified.1This specification is under the jurisdiction of ASTM Committe
13、e F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.Current edition approved Apr. 10, 2002. Published June 2002. Originallypublished as F 409 75. Last previous edition F 409 99a.2Annual Book of ASTM Standards, Vol 08.01.3Annual Book of ASTM Standards, Vol 08
14、.04.4Annual Book of ASTM Standards, Vol 08.02.5Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5098, Attn: NPODS.6Available from the American National Standards Institute, 25 W. 43rd St., 4thFloor, New York, NY 10036.7Available from the
15、 International Association of Plumbing and MechanicalOfficials, 20001 E. Walnut Drive, South Walnut, CA 91789-2825.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.1.1 The plumbing terminology used in this specification isin accorda
16、nce with the definitions given in the UniformPlumbing Code, unless otherwise indicated.4. Significance and Use4.1 The requirements of this specification are intended toprovide accessible and replaceable tube and fittings to conveydomestic waste from fixtures to the drain, waste, and vent(DWV) system
17、.5. Materials and Manufacture5.1 TubeThe tube shall be made of one of the followingmaterials:5.1.1 Virgin acrylonitrile-butadiene-styrene (ABS) plasticwhich shall meet the requirements of Specification D 3965,Cell Classification 4-2-2-2-2.5.1.2 Virgin poly(vinyl chloride) (PVC) plastic which shallme
18、et the requirements for 12454C materials in accordance withSpecification D 1784, or5.1.3 Virgin polypropylene plastic which shall meet therequirements of Specification D 4101, Cell ClassificationPP0110B55140 and PP0105G20A33350.5.2 Fittings and Mechanical Joint ComponentsThe fit-tings and components
19、 of mechanical joints shall be comprisedof one or more of the following materials:5.2.1 Virgin ABS plastic which shall meet the requirementsof Specification D 3965, Cell Classification 2-0-2-1-1.5.2.2 Virgin PVC plastics which shall meet the requirementsof 12454C materials as defined in Specificatio
20、n D 1784, or5.2.3 Virgin polypropylene plastic which shall meet therequirements of Specification D 4101, Cell ClassificationPP0110B55140, and PP0105G20A33350.5.3 Rework MaterialThe manufacturers shall use onlytheir own clean rework tube and fitting material and the tube orfittings produced shall mee
21、t all the requirements of thisspecification. The different types of material shall not bemixed.5.4 Solvent CementThe solvent cement shall meet therequirements of Specification D 2235 or Specification D 2564.No cement joining of propylene plastic (PP) is permissible.6. Mechanical Connections6.1 Compr
22、ession or threaded connections shall incorporateAmerican National Straight Pipe Thread, Mechanical Joints forFixtures (NPSM). The thread form shall be the form ofAmerican National Straight Pipe Thread and the dimensionsshall be in accordance with ANSI B1.20.1 (NPSM). All threadsshall have a minimum
23、three-thread engagement for fittings andplastic nuts.6.2 Taper Pipe ThreadsFor all fittings having taper pipethreads, threads shall conform to Specification F 1498 and begaged in accordance with 8.5.6.3 Straight Pipe Threads (NPSM)For all fittings havingstraight pipe threads, threads shall conform t
24、o ANSI B1.20.1(NPSM) and be gaged in accordance with 8.6.6.4 All tube and fittings made from propylene plastic shallbe assembled by either mechanical connections or by heatfusion, in accordance with Practice D 2657.7. Requirements7.1 GeneralThe tube and fittings shall be homogeneousthroughout and fr
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF4092002STANDARDSPECIFICATIONFORTHERMOPLASTICACCESSIBLEANDREPLACEABLEPLASTICTUBEANDTUBULARFITTINGS
链接地址:http://www.mydoc123.com/p-536596.html