ASTM F406-2013 Standard Consumer Safety Specification for Non-Full-Size Baby Cribs Play Yards《非实际大小的婴儿床 玩耍场地的标准消费者安全规范》.pdf

《ASTM F406-2013 Standard Consumer Safety Specification for Non-Full-Size Baby Cribs Play Yards《非实际大小的婴儿床 玩耍场地的标准消费者安全规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F406-2013 Standard Consumer Safety Specification for Non-Full-Size Baby Cribs Play Yards《非实际大小的婴儿床 玩耍场地的标准消费者安全规范》.pdf（46页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F406 12aF406 13Standard Consumer Safety Specification forNon-Full-Size Baby Cribs/Play Yards1This standard is issued under the fixed designation F406; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, the year of last re

2、vision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONThis consumer safety specification addresses incidents associated with non-full-size cribs/playyards that were identified by the

3、U.S. Consumer Product Safety Commission (CPSC).Incidents identified by the CPSC and addressed in this standard include asphyxiation due toentrapment in mesh drop side units left with a side down, strangulation by entanglement on protrudinghardware, strangulation by button entrapment in mesh openings

4、, strangulation due to failure of thecenter hinge on a top rail, collapse or failure of the locking devices, collapse of the floor or sides, andchoking on vinyl bitten from the top rail. This specification also addresses wooden non-full-size cribinjuries or deaths due to entanglement on corner post

5、extensions, dislodgment of slats resulting frombreakage or failure of glue joints, collapse of mattress support, detachment of screws, dislodgementof teething rails, and entanglement on cords or strings.This specification is not intended to cover non-full-size cribs/play yards that are either blatan

6、tlymisused or abused. This specification is written within current state-of-the-art of non-full-sizecrib/play yard technology and is intended to be updated if substantive information becomes availablethat necessitates additional requirements or justifies revision of existing requirements.1. Scope1.1

7、 This consumer safety specification establishes testing requirements for structural integrity and performance requirements fornon-full-size cribs/play yards, both rigid sided and mesh/fabric assemblies. It also provides requirements for labeling andinstructional material. The term unit or product wi

8、ll refer to a non-full-size crib/play yard.1.2 This specification covers a framed enclosure with a floor made for the purpose of providing sleeping and playingaccommodations for a child who cannot climb out and is less than 35 in. (890 mm) in height. It also covers bassinet, changingtable, or simila

9、r accessories to a non-full size crib/play yard. These accessories shall also comply with the applicable requirementsofASTM standards addressing those accessories. For example, a changing table that attaches to a play yard shall also comply withthe applicable requirements in Specification F2388. Thi

10、s specification does not cover inflatable products.1.3 No product produced after the approval date of this consumer safety specification shall, either by label or other means,indicate compliance with this specification unless it conforms to all applicable requirements contained herein, before and af

11、ter alltesting.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information only and are not considered standard.1.5 The following safety hazards caveat pertains only to the test me

12、thod portion, Section 8, of this specification:This standarddoes not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health practices and determine the applicability of regulatory

13、 limitations prior to use.NOTE 1This consumer safety specification includes the following sections:Title SectionScope 1Referenced Documents 2ASTM Standards 2.11 This consumer safety specification is under the jurisdiction of ASTM Committee F15 on Consumer Products and is the direct responsibility of

14、 Subcommittee F15.18on Cribs, Toddler Beds, Play Yards, Bassinets, Cradles and Changing Tables.Current edition approved May 1, 2012May 1, 2013. Published May 2012May 2013. Originally approved in 1977. Last previous edition approved in 2012 asF406 12.F406 12a. DOI: 10.1520/F0406-12A.10.1520/F0406-13.

15、This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior edi

16、tions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1Federal Regulations 2.4Terminology 3Definitions

17、of Terms Specific to This Standard 3.1Conspicuous 3.1.2Conspicuous 3.1.4Cord 3.1.3Cord 3.1.5Corner Post 3.1.4Corner Post 3.1.6Dropside/Dropgate 3.1.5Dropside/Dropgate 3.1.7Dynamic Load 3.1.6Dynamic Load 3.1.8Fabric 3.1.7Fabric 3.1.9Foldable Side or End 3.1.8Foldable Side or End 3.1.10Key Structural

18、Elements 3.1.9Key Structural Elements 3.1.11Manufacturers Recommended Use Position 3.1.10Manufacturers Recommended Use Position 3.1.12Mattress 3.1.11Mattress 3.1.13Mesh 3.1.12Mesh 3.1.14Mesh/Fabric Crib 3.1.13Mesh/Fabric Crib 3.1.15Nonpaper Label 3.1.16Nonpaper Label 3.1.18Occupant 3.1.17Occupant 3.

19、1.19Paper Label 3.1.18Paper Label 3.1.20Play Yard 3.1.19Play Yard 3.1.21Protrusion 3.1.20Protrusion 3.1.22Rigid Sided Crib 3.1.21Rigid Sided Crib 3.1.23Seam 3.1.22Seam 3.1.24Static Load 3.1.23Static Load 3.1.25Stationary Side 3.1.24Stationary Side 3.1.26Structural Failure 3.1.26Structural Failure 3.

20、1.28Calibration and Standardization 4General Requirements 5Corner Posts 5.1Scissoring, Shearing, or Pinching 5.6Latching and Locking Mechanisms 5.8Openings 5.9Protective Components 5.10Labeling 5.11Stability 5.12Cord/Strap Length 5.13Coil Springs 5.14Entrapment in Accessories 5.15Mattress 5.16Mattre

21、ss for Rigid Sided Products 5.17Protrusions 5.18Bassinet/Cradle Accessories MissingAccessory Attachment Components5.19Record Keeping 5.20Performance Requirements for Rigid Sided Units 6Crib-Side Height 6.2Spacing of Unit Components 6.3Hardware 6.4Fasteners 6.5Construction and Finishing 6.6Requiremen

22、ts for Cutouts 6.7Plastic Teething Rail 6.11Cyclic Test 6.12Side(s) or End(s) Latch Testing, or Both 6.13Dropgate Latch Testing 6.13.1Foldable Side or End Latch Testing 6.13.2F406 132Mattress Support System Vertical Impact TestRequirements6.14Mattress Support System Vertical Impact TestRequirements6

23、.14Mattress Support System Testing 6.15Crib Side Test Requirements 6.16Spindle/Slat Strength Testing 6.17Performance Requirements for Mesh/Fabric Units 7Height of Sides 7.2Side Deflection and Strength 7.3Floor Strength 7.4Top Rail Covering Material 7.5Mesh Requirements 7.6Mesh Openings 7.6.1Mesh Str

24、ength 7.6.2Fabric Material Requirements 7.7Fabric Strength 7.7.1Mesh/Fabric Assembly Requirements 7.8Sewn Assembly 7.8.1Seam Strength 7.8.2Mesh/Fabric Attachment Strength 7.8.3Mattress Vertical Displacement 7.9Top Rail Configuration 7.10Top Rail to Corner Post Attachment 7.11Test Methods 8Component

25、Spacing Test Apparatus 8.1Component-Spacing Test Method 8.2Test Requirements for Cutouts 8.3Plastic Teething Rail Test for Rigid SidedProducts8.4Plastic Teething Rail Test for Rigid SidedProducts8.4Cyclic Test 8.5Side or End Latch Test, or Both, for Rigid SidedProducts8.6Side or End Latch Test, or B

26、oth, for Rigid SidedProducts8.6Movable Side Latch Tests 8.6.3Hinged Drop Gate Latch Test 8.6.4Test Procedure for Latches to Prevent Foldingof a Foldable Side or End8.6.5Test Procedure for Latches to Prevent Foldingof a Foldable Side or End8.6.5Mattress Support System Vertical Impact Test forRigid Si

27、ded Products8.7Mattress Support System Vertical Impact Test forRigid Sided Products8.7Mattress Support System Test for Rigid SidedProducts8.8Mattress Support System Test for Rigid SidedProducts8.8Crib Side Test 8.9Crib Side Cyclic Tests 8.9.4Crib Side Static Test 8.9.5Crib Side Spindle/Slat Torque T

28、est 8.9.6Spindle/Slat Static Load Strength 8.10Side Deflection and Strength Tests forMesh/Fabric Cribs8.11Side Deflection and Strength Tests forMesh/Fabric Cribs8.11Floor Strength Test for Mesh/Fabric Cribs 8.12Locking Mechanism Test 8.13Dropgate Locking Device Test Method 8.13.1Folding Latch Test M

29、ethod 8.13.2Mesh Opening Test 8.14Test for Strength of Mesh and Integrity ofAttachment8.15Test for Strength of Mesh and Integrity ofAttachment8.15Mesh/Fabric Attachment Strength Test Method 8.16Test for Stability of Product 8.17Permanency of Labels and Warnings 8.18Adhesion Test 8.19Nonpaper Labels

30、8.20Removal of Protective Components 8.21Torque Test 8.21.3Tension Test 8.21.4Vinyl Thickness Measurement 8.22F406 133Test for Attachment of Storage Pouch or OtherParts with Printed Warnings8.23Test for Attachment of Storage Pouch or OtherParts with Printed Warnings8.23Cord/Strap Length Test Method

31、8.24Protrusions 8.25Entrapment Tests 8.26False Latch 8.27Mattress Vertical Displacement Test 8.28Top Rail Configuration Test 8.29Minimum Space when Folded 8.29.1Top Rail V-Shape Configuration Test 8.29.2Top Rail to Corner Post Attachment Test 8.30Load Application Procedure 8.30.3Bassinet and Cradle

32、Accessory SleepSurface Collapse/Tilt8.31Marking and Labeling 9Labeling 9.1Warning Statements 9.2Instructional Literature 10Warning Statements 10.1.2Water Mattress Use 10.3.3Keywords 11Design Guidelines for Protrusions Annex A22. Referenced Documents2.1 ASTM Standards:2D1424 Test Method for Tearing S

33、trength of Fabrics by Falling-Pendulum (Elmendorf-Type) ApparatusD1683 Test Method for Failure in Sewn Seams of Woven Apparel FabricsD3359 Test Methods for Measuring Adhesion by Tape TestD5034 Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)F963 Consumer Safety Specifi

34、cation for Toy SafetyF1004 Consumer Safety Specification for Expansion Gates and Expandable EnclosuresF1487 Consumer Safety Performance Specification for Playground Equipment for Public UseF2388 Consumer Safety Specification for Baby Changing Tables for Domestic Use2.2 EN Standards:3EN 7161:1995 Cot

35、s and Folding Cots for Domestic UseEN 122271:1999 Playpens for Domestic Use2.3 ISO Standard:4IS0 8124-1:2000 Safety Aspects Related to Mechanical and Physical Properties2.4 Federal Regulations:516 CFR 1303 Ban of Lead-Containing Paint and Certain Consumer Products Bearing Lead-Containing Paint16 CFR

36、 1500 Hazardous Substances Act Regulations including sections:1500.3 (c) (6) (vi) Definition of “Flammable Solid”1500.44 Method for Determining Extremely Flammable and Flammable Solids1500.48 Technical Requirements for Determining a Sharp Point In Toys and Other Articles Intended for Use By Children

37、Under Eight Years of Age1500.49 Technical Requirements for Determining a Sharp Metal or Glass Edge in Toys or OtherArticles Intended for Use ByChildren Under Eight Years of Age1500.50-.52 Test Methods for Simulating Use and Abuse of Toys and Other Articles Intended for Use By Children16 CFR 1501 Met

38、hod for Identifying Toys and Other Articles Intended for Use By Children Under Three Years of Age WhichPresent Choking, Aspiration, or Ingestion Hazards Because of Small Parts16 CFR 1509 Requirements for Non-Full-Size Baby Cribs3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 a

39、ccessory, ncomponent with a rigid frame such as a bassinet or changing table that attaches to a non-full size crib/playyard and that, because of its structure, location, or movement, may expose a non-full size crib/play yard occupant to an openingpresenting an entrapment hazard. It does not include:

40、 (1) items that hang outside the occupant areas, such as organizers and storage2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on

41、 the ASTM website.3 Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036.4 Available from International Organization for Standardization (ISO), 1 rue de Varemb, Case postale 56, CH-1211, Geneva 20, Switzerland.5 Available from U.S. Government Pri

42、nting Office Superintendent of Documents, 732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401.F406 134bags, (2) canopies that have no rigid frame members running alongside any top rail, and (3) accessories that attach only to anotherattachment and not directly to the non-full size crib/play

43、 yard.3.1.1.1 DiscussionRationale: Definition applies only to accessories that attach to non-full size crib/play yard, not accessories that attach to bassinetor changing table. This would exclude a changing table that attaches only to a bassinet, since a bassinet occupant is not able topush up on ha

44、nds and knees, and therefore is not at risk from an entrapment hazard.3.1.2 accessory attachment components, nthe components that provide the means of attachment for a bassinet/cradleaccessory to a play yard. (See Fig. A1.1.)3.1.3 bassinet/cradle accessory, nan elevated sleep surface that attaches t

45、o play yard designed to convert the product into abassinet/cradle intended to have a horizontal sleep surface while in a rest (non-rocking) position.3.1.4 conspicuous, adjDescribes a label that is visible, when the unit is in a manufacturers recommended use position, to aperson standing near the uni

46、t at any one position around the unit but not necessarily visible from all positions.3.1.5 cord, nlength of slender flexible material including monofilaments, rope, woven and twisted cord, plastic and textiletapes, ribbon, and those materials commonly called string.3.1.6 corner post, nvertical post

47、located at the corner of a product.3.1.7 dropgate, nside that is intended to pivot with respect to the frame when the product is in the manufacturersrecommended use position to provide easier access to the occupant.3.1.7.1 DiscussionRationale: The word “telescope” was deleted because telescoping sid

48、es are really covered under the definition of movable sides.Dropgates are products that pivot only. For reference, the definition of movable side in Consumer Safety Specification F406 is “topportion of an otherwise stationary side that is intended to move with respect to the frame (other than a fold

49、able side) when theproduct is in the manufacturers recommended use position to provide easier access to the occupant.3.1.8 dynamic load, napplication of an impulsive force through free fall of a weight.3.1.9 fabric, nany woven, knit, coated, laminated, extruded or calendered flexible material that is intended to be sewn, welded,heat sealed, or glued together as an assembly.3.1.10 foldable side or end, nside or end panel intended to be stationary with respect to the frame when a product is in themanufacturers recommended use position, but that folds